ページ1に含まれる内容の要旨
Volume
1
Instruction Manual
EDSR400F/600F/
EDSR400F/600F/
EDSR900F/1600F
EDSR900F/1600F
ページ2に含まれる内容の要旨
EVERFOCUS ELECTRONICS CORPORATION EDSR 400F / EDSR600F EDSR 900F / EDSR1600F Instruction Guide © 2004 Everfocus Electronics Corp 2445 Huntington Drive Phone 626.844.8888 • Fax 626.844.8838 All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the Everfocus Electronics Corporation. QuickTime is a registered trademark of the Apple Computer, Inc. Windows is a registered tr
ページ3に含まれる内容の要旨
Table of Contents Introduction I System Setting Menu 39 CHAPTE R 4 CHAPTE R 1 Recording Overview 42 Product Overview 1 Basic Recording Setup 42 Features 1 Timer Recording Setup 43 Specifications 2 Motion Recording Setup 44 Front Panel Keys 3 Alarm Recording Setup 45 Back Panel Keys 5 CHAPTE R 5 CHAPTE R 2 Playback Overview 47 Installation 7 Basic Playback 47 Basic Wiring Instructions 8 Search Playback 47 Hard Disk Drive Installation 9 Segment List Playback 47 Final Ins
ページ4に含まれる内容の要旨
Subnet Masks 58 Gateway Address 59 APPENDI X D Virtual Ports 59 RJ45 (RS485) Pin Assignment 99 Pre-Installation 60 What type of Network Connection 61 TROUBL E SHOOTIN G Simple One to One Connection 62 Troubleshooting 100 Direct High Speed Modem Connection 68 Router or LAN Connection 70 CHAPTE R 10 Linksys Port Forwarding 73 Dynamic DNS 77 CHAPTE R 11 D-Link Port Forwarding 79 Dynamic DNS 82 CHAPTE R 12 DDNS 84 Creating a DDNS Account 84 CHAPTE R 13 Viewing through Internet Ex
ページ5に含まれる内容の要旨
Currently, some Internet Service Providers (ISPs) may be blocking certain internet ports, disabling remote access to your EDSR unit over the internet. Due to certain security risks, your ISP may refuse to unblock these specific ports. EverFocus now offers a firmware update specifically for the EDSR line of digital recorders which directly addresses this issue: firmware version 1.09 allows you to change the default HTTP and Data ports used by the DVR. This will provide a wo
ページ6に含まれる内容の要旨
Note: Once the Ports have been changed, these will be the ports that will need to be Forwarded if a NAT router (Linksys, Netgear, Dlink, etc.) is in use. Due to all internet Browsers (Internet Explorer, Netscape Navigator, etc.) defaulting to use port 80 as the HTTP port; if the HTTP port number is changed from 80 to something else, the HTTP port must be specified when connecting to the DVR. Example: IP address of the DVR is 146.82.96.172. ISP is blocking port 80, so H
ページ7に含まれる内容の要旨
EDSR PTZ setup. Once the data cables are connected, the EDSR recorder is configured to communicate with PTZ camera or cameras. Please Note: you need to determine what Protocol and Baud Rate is used for the cameras. (Note: All cameras connecting to the same DVR MUST be on the same Protocol and Baud Rate.) SETTINGS: 1.) Access the Setup menu by pressing [MENU] on the front of the unit. 2.) Use the Jog Wheel to highlight the PTZ menu. Press[ENTER] 3.) In PTZ SETTINGS sub-menu, use [ENT
ページ8に含まれる内容の要旨
VIEWING Once you access the unit via the web-page. The option for the PTZ controls will be on the Right Panel.
ページ9に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Chapter 1 Product Overview DVRs are the industry’s first full-featured digital video recorder designed specifically for use within the security industry. The Digital Video Recorder incorporates all the benefits of digital video recording, is simple to install, and operates just like a VCR. Highly efficient compression technology and superior resolution of recorded images make the Digital Video Recorder stand out from the competition as the best choic
ページ10に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Specifications 2
ページ11に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Front Panel Keypads Keys: 3
ページ12に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON 4
ページ13に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Back Panel Connections 5
ページ14に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON 6
ページ15に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Chapter 2 Installation The installations described below should be made by qualified service personnel or system installers. Please refer to the following diagram for the basic wiring connections. Please Note: Monitors and Cameras must be purchased separately. EDSR400: Camera 1~4 / EDSR600: Camera 1~6 EDSR900: Camera 1~9 / EDSR1600: Camera 1~16 Diagram 1 7
ページ16に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Basic Wiring Instructions Please refer to diagram 1 on page 9 to assist you with this portion of the installation. Power: Connect the power source or adapter into the power socket shown in diagram 1. Please Note: Do not plug the digital video recorder into the same power source as the cameras. Cameras: Connect each cameras video output to the video input on the digital video recorder shown in diagram 1. Please Note: At least one camera must be co
ページ17に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Hard Disk Drive Installation The first step in installing the hard drive is to insert the hard drive sleeve into the machine. The hard disk drive default setting is initially set to master. The second step is to insert the key provided and turn the tray key to the lock position. If this process is ignored the hard disk drive will not be detected. Follow the previous steps for the second hard drive or second empty sleeve. Please Note: If the Hard Disk
ページ18に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Chapter 3 DVR Menu Setup Assuming you have completed the first two chapters of this manual. You are now ready to begin setting up the digital video recorder menu. To begin this process, press the MENU key. Once inside the main menu you will find there are 15 setup option pages as follows. Diagram 2 Turning the jog dial clockwise or counter clockwise will allow you to scroll through the different menu setup option pages.
ページ19に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Clock Setting Menu Diagram 3 Diagram three is a screen shot of the Clock/Language Setting Menu. In the Clock/Language Setting Menu the following fields are defined as follows: Date: This field represents the current date on the DVR. To change this, simply use the Jog Dial on the DVR. Press the Enter key to make your selection. The date is represented as follows: Year: 2000~2099 / Month: 01~12 / Date: 01~31 (Day of Week) Time: This field
ページ20に含まれる内容の要旨
EVERFOCUS ELECTRONI CS CORPORATI ON Menu Language: This field is set to English from factory and can not be changed. Video System: This field is set to NTSC from factory which is the North American Video Standard and can not be changed. The European and Asian Video Standards are PAL. Version: This field represents the firmware version the digital video recorder is using. Please Note: New firmware versions are available for download from our ftp site. ftp://64.210.7.210 (see pa
