ページ1に含まれる内容の要旨
INSTALLATION / OPERATION
EDR-920
9-channel Digital Video Recorder
EDR-1640
16-channel Digital Video Recorder
Rev 1.00
ページ2に含まれる内容の要旨
Safety warnings Safety warnings To avoid any damage, please consider the following safety warnings: Never place the recorder near to heaters, furnaces, other heat sources or under direct solar irradiation. Operate the device only in locations providing the tolerable operating temperature range 0 °C~40 °C. Make sure that the device‘s ventilation slots are not covered or sheeted. For cleaning, make sure the device is plugged off and only use a damp cloth without acid detergent. Install the dev
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. Introduction 4 1.1 Features 4 1.2 Delivery scope 4 1.3 Technical data 5 1.4 Front panel operating elements 7 1.5 Connections 10 1.6 Screen displays 12 2. Installation 15 2.1 Delivery scope 15 2.2 Video connection installation, DVR cascading 15 2.3 Audio connection installation 17 2.4 RS-485 keyboard installation 18 2.4.1 General RS-485 bus installation 18 2.4.2 RS-485 connection assignment 20 2.4.3 EKB-500 connection through network patch cable 20 2.4.4 EKB-500 connection
ページ4に含まれる内容の要旨
TABLE OF CONTENTS 4. Recording 56 4.1 Normal recording 56 4.2 Timer – scheduled recording 56 4.3 Event recording 57 5. Playback 58 5.1 Playback without search function 58 5.2 Recording search 60 6. Video export 62 7. Call- / matrix monitor setup 64 8. Display settings 65 9. Screen display 66 10. EDA 966 infrared remote control (optional) 67 11. Network access 68 Appendix A: EDR viewer software 73 Appendix B: Interface specification 75 Appendix C: Serial remote control protocol 76 Appendix D: Re
ページ5に含まれる内容の要旨
1. INTRODUCTION The latest EverFocus digital video recorder generation is based on MPEG-4 compression technology, resulting in enhanced recording capacity and improved network image transmission speed with high image quality. Comprehensive features and extended event recording settings enable the almost universal application of this DVR series. 1.1 FEATURES • Duplex operation: simultaneous recording and playback •MPEG4 compression method with configurable quality • variable recording rate
ページ6に含まれる内容の要旨
1.3 TECHNICAL DATA Video format PAL/CCIR EDR920: 9 x 1 Vpp FBAS, BNC, 75 Ohm Video input EDR1640: 16 x 1 Vpp FBAS, BNC, 75 Ohm Main monitor: 1 Vpp FBAS, BNC at 75 Ohm Video output CALL/MATRIX monitor: 5 x 1 Vpp FBAS, BNC at 75 Ohm 9/16 x loop-through outputs 1 Vpp FBAS, BNC at 75 Ohm Video compression MPEG4 Recording resolution 720x288, 720x576 or 360x288 Main monitor: full screen, PiP, 4,7,9,10*,13*,16* , 2 x zoom, sequence Display modes Call/matrix monitor: full screen, seque
ページ7に含まれる内容の要旨
Title generator Max. 12 characters per camera Network RJ45 socket Image export USB 2.0 interface RS-232 9-pin Sub-D socket RS-485 2 x RJ45 4 x input 500 mV max /10KOhm, Audio 1 x output 500 mV max at 10KOhm Power source 100 ~ 240 VAC Power consumption 185 W max. Dimensions 430 (W) x 88 (H) x 300 (D) mm Weight 6,24 KG o o Ambient temperature 0 C ~ +40 C Remote control optional: IR remote control, RS-485 keyboard 6
ページ8に含まれる内容の要旨
1.4 FRONT PANEL OPERATING ELEMENTS 9 11 13 21 19 17 8 10 12 14 15 20 18 1 3 5 7 23 22 2 4 6 16 Keys 1 REC: recording key 2 STOP: recording / playback stop 3 PLAY: playback PAUSE: image freeze, stops playback for freeze mode 4 5 SEARCH: opens on-screen display for playback search COPY: opens image export menu. In playback mode, the current playback position is 6 stored as image export start position. 7 ENTER: Enter key for input confirmation 8 DISPLAY: main monitor status display switchin
ページ9に含まれる内容の要旨
SELECT: In multiscreen mode: selection of the camera to be displayed in a partial screen. 9 ENTER switches to the following partial screen. In full screen mode: brightness, contrast and colour adjustment for this video channel. 10 MODE: Multiscreen display switching, repeated actuation switches between the individual displays. 11 ZOOM: In full screen mode: 2x electronical zoom. Zoom screen can be moved through JOG . ENTER key changes the direction. Further zoom key actuation switches the el
ページ10に含まれる内容の要旨
20 HDD LEDs: LEDs for HDD power (green) and HDD activity (red) LCD display: Status, time/date display 21 IR receiver: Receiver for infrared remote control 22 USB socket: USB-2.0 port for image export via USB stick resp. external DVD-R EPR200 23 9
ページ11に含まれる内容の要旨
1.5 CONNECTIONS 5 1 10 8 6 4 11 12 2 7 3 9 14 15 13 EDR1640 back panel (EDR920 identical, 9 video inputs) Main switch: Power switch, below IEC socket for 100~240 VAC power source 1 Audio inputs: Audio inputs 1 ~ 4 2 Audio output: Audio output 3 MAIN monitor: Main monitor for live and playback display and on-screen display CALL monitor: CALL monitor output. Spotmonitor for full screen live display, sequence 4 mode and alarm camera switching 5 Video inputs: EDR920: VIDEO IN(1~9): BNC video inp
ページ12に含まれる内容の要旨
7 LAN: RJ45 network socket RS232 socket: 9-pin Sub-D control input for RS-232 remote control 8 RS485 socket: 2 x RJ45 socket (equal) for remote control via RS-485 9 keyboards and telemetry control (network-controlled) Fan: Fan air outlet, please do not cover 10 Matrix monitors 1~4: Matrix monitor outputs 1~4 11 12 SCSI-socket: EDA800s HDD expansion unit connection 13 Mouse: PS-2 mouse connection (optional) 14 S-Video: Main monitor Y/C output Cascade IN / OUT: Monitor input / output for EDR ca
ページ13に含まれる内容の要旨
1.6 SCREEN DISPLAYS Here’s an overview of the screen displays appearing on the MAIN monitor: 1. Channel display 2. Event (here: video loss) 3. Display selection 4. Playback status 5. Recording status 1 Channel display: shows the selected video channel’s description Event: Event display, may be channel-related or global 2 Channel-related types of event: Alarm: Display of an alarm triggered by alarm input contact A Motion: Motion detection of the respective camera M Video loss: Video signal los
ページ14に含まれる内容の要旨
SELECT: Within a multiscreen view, the SELECT key activates the camera selection mode. The 3 active camera field shows “S”. Use the JOG to switch between the camera fields. Use the channel keys 1~9 or 1~16 to switch the channel.. 4 PLAYBACK STATUS: The playback-relevant information are displayed in this status bar. Playback date Playback status Playback position 1. Playback date : Current playback date 2. Playback status: Playback operation mode “PAUSE”: Freeze image mode “>”: n
ページ15に含まれる内容の要旨
1. Current date: as set in time/date menu 2. Recording status: In case of activated recording, "R" + current HDD no. is displayed “R01”: R - RECORD, figure shows the currently recording HDD no., here: No. 1 3. Event: current event display 4. Current time: as set in time/date menu 5. HDD fan message: “No Disk”: no HDD available or detected “No Fan”: fan malfunction "HDD OT": HDD over temperature 14
ページ16に含まれる内容の要旨
2. INSTALLATION ATTENTION: The installation should be effected by qualified personnel only. Connect power source only after having finished the further installation. 2.1 Delivery scope Check the delivery scope (see 4.) before starting the installation. 2.2 Video connection installation, DVR cascading Sample installation with maximum camera and monitor configuration: Cameras and monitors have to be cabled with 75 Ohm video cable, e.g. RG-59, RG-12 and suitable BNC plugs. Due to inappropriate
ページ17に含まれる内容の要旨
DVR cascading The digital video recorders provide "CASCADE IN" and "CASCADE OUT" video connections. In combination with RS-485 remote control, up to 8 EDR920/1640 can be cascaded and administrated via one single main monitor. Cascading is effected by connecting the DVRs „CASCADE OUT“ to the „CASCADE IN“ of the following DVR, while the last „CASCADE OUT“ is connected to the monitor input. By means of the RS-485 address sent from the keyboard, the respective DVR is switched on the monitor. T
ページ18に含まれる内容の要旨
2.3 Audio connection installation Sample installation with audio connection to video cameras providing audio output: The EDR920/1640 DVRs provide 4 audio inputs and 1 audio output. The inputs are designed for max. 500 mV to 10 KOhm line audio signals. ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone amplifier is required). The installation has to be effected with audio coax cable and RCA plugs. The output provides a max. 500 mV to 10 KOhm line audi
ページ19に含まれる内容の要旨
2.4 RS-485 keyboard installation All EDR920/1640 functions can be remote-controlled by the EKB 500 universal keyboard. Using the EEPbus protocol, digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus. One system can comprise up to 8 keyboards. 2.4.1 General RS-485 bus installation EKB-500 uses an RS-485 simplex wiring; the signal is transferred via a single twisted pair line. CAT5 network cable is recommended, UPT version (unshielded) is sufficient for
ページ20に含まれる内容の要旨
A direct RS-485 bus star wiring is not supported; star wiring requires the use of signal distributors. Improper RS-485 bus star wiring If star wiring is inevitable, EDA 997A RS-485 signal distributors may be used. The maximum system cable length can also be expanded by using these distributors, physically providing a new RS-485 bus with 1200 m cable length each at every distributor output. Star wiring with RS-485 signal distributor In case the maximum number of 32 bus participants is exce
