ページ1に含まれる内容の要旨
MP-4100/4200 Mobile DVR
INSTRUCTION GUIDE
www.datavideo-tek.com
ページ2に含まれる内容の要旨
Table of contents Warnings and Precautions --------------------------------------------------------------2 Radio and Television Interference-----------------------------------------------------3 Tech support---------------------------------------------------------------------------------4 The difference between model nos. MP-4100 & MP-4200----------------------4 Features --------------------------------------------------------------------------------------5 System Installation-----------
ページ3に含まれる内容の要旨
Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6. Slots and openings on the cabinet top, back, and bottom are
ページ4に含まれる内容の要旨
Radio and Television Interference UNITED STATES: The equipment described in this manual generates and uses radio frequency energy. If it is not installed and used in accordance with the instructions in this manual, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful int
ページ5に含まれる内容の要旨
Tech support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo-tek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300-U East Washington Blvd., Whittier, CA 90606 USA Tel: +1 562 696 2324 www.datavideo.us Datavideo Technologies Europe BV Californiedreef 263565 B
ページ6に含まれる内容の要旨
FEATURES 20 seconds of pre-event recording Stand alone NON-PC embedded system offering maximum stability Simple, easy to use control & user interface Near DVD quality MPEG2 recording and playback Video recording with Digital Watermark MP3-level high quality audio recording (32KHz sampling rate) Remote control panel Removable 2.5 ” Hard Drive facility Multiple recording modes - alarm event recording and instant recording Video loss detection with alarm and pre-al
ページ7に含まれる内容の要旨
INSTALLATION Connect a RMC-110 10-Key Remote Control key pad for system configuration. N.B. Ensure that your camera connected and working, or you will get a “Video Loss” event. RMC-110 6
ページ8に含まれる内容の要旨
INSTALLATION Connect a RMC-80 5-Key Remote Control key pad for the application in a vehicle. N.B. Ensure that your camera connected and working, or you will get a “Video Loss” event. RMC-80 7
ページ9に含まれる内容の要旨
Introduction of RMC-110 10-Key Remote Control Key Pad 1. LCD: No Function 2. Turn ON / OFF Main Menu 3. Start / End Instant recording, Stop playback, Switch to Monitoring state 4. Turn ON / OFF Main Menu 5. Turn ON / OFF Event List Menu 6. Page down 10% of the entire list, instant Replay, instant Review 7. Select ZOOM in, GO back 8. Move the highlight up, Increase numbers, Switch characters upwards, Play / Pause ZOOM in 9. Move the highlight down, decrease numbers
ページ10に含まれる内容の要旨
Configure MP-4100 by RMC-110 Check Box serial number, firmware version and Box IP address Press on the “MENU” key on RMC-100 to Pop Up the “Main Menu”. Select “Information” and press on the key. You will enter the Information menu. Select “Box Information” and press on key to find the Box serial number. Press on key to Exit Information 9
ページ11に含まれる内容の要旨
Check Hard Disk Info, Video System and Resolution Press on the key to pop up “Main Menu” Select “Information” and press on the key, you will enter the Information menu. Use the key to move the highlight and Select “Hard Disk Information”. Press on the key to check Hard Disk and Video Information Press on the key to exit Information 10
ページ12に含まれる内容の要旨
Check Log Information Press on the key to popup the “Main Menu”. Select “Information” and press on the key to enter “Information menu”. Use the key to move the highlight and select “Log Information”. Press on the key. You will see Log Information Press on the key to exit Information 11
ページ13に含まれる内容の要旨
Video recording setting Press on the key to pop up “Main Menu” Use the key to move the highlight and select “Recording Settings” Press on the key to enter “Recording Settings” Menu Select “Recording Quality”, and then press Enter key Use the key to move around. Use the key to specify each item. Use the key to highlight the “Save” button and press on the key to save and pop up the System Settings menu. Press on the “MENU” key to end the setup, 12
ページ14に含まれる内容の要旨
Recording Video Quality There are 4 different bit-rates offered in MP-4100 (directly related to video quality) Recording Bit-rate Quality Level Quality High 3Mbps Near-DVD quality Fine 2Mbps Super VCD quality Normal 1.2Mbps VCD quality Low 800Kbps VCR-like quality Recording Frame Rate? There are 4 selectable frame rates in MP-4100 which are 30,10, 2 or1 fps for NTSC Video and 25,8.5,1.2,0.8 fps for PAL Video Frame-rate Quality Description (fps) 30fps_NTSC Completely smo
ページ15に含まれる内容の要旨
Recording Time in a 60GB or 80GB HDD The estimated recording time on a 60GB HDD is about 46 hours with 30fps (NTSC video) and highest video recording quality (D1 resolution of 704 x 480) The estimated recording time on a 80GB HDD is about 61 hours with 30fps (NTSC video) and highest video recording quality (D1 resolution of 704 x 480) The estimated recording time on a 120GB HDD is about 92 hours with 30fps (NTSC video) and highest video recording quality (D1 resolution of 704 x 480)
ページ16に含まれる内容の要旨
Alarm Settings Press on the key on RMC-110 to pop up “Main Menu”. Use key to move the highlight and select “Recording Settings”. Press on the key to enter “Recording Settings” Menu Use the key to move the highlight and select “Alarm Settings”. Press on the key to enter “Alarm Settings” Menu Use the key to move around. Use the key to specify each item. Use the key to highlight the “Save” button and press the key to save and pop up the System Settings menu. Press on the “MENU” key to en
ページ17に含まれる内容の要旨
Change Network IP and MASK settings Press the key on the RMC-110 Remote key to pop up the Main Menu. Use the key to move the highlight and select “System Settings”. Press on the key to enter System Settings menu and select “Connection Settings”. Select “Ethernet Settings” and press on the key. 16
ページ18に含まれる内容の要旨
Use the key or key to enable or disable. Once DHCP is enabled, DVR can obtain the IP address automatically from your DHCP server. Otherwise, you need specify the following 3 items manually. Use the key or key to specify the 32-bit IP address manually, if DHCP is disabled. Use the key or key to specify the 32-bit subnet mask manually, if DHCP is disabled. Use the key or key to specify the 32-bit default gateway manually, if DHCP is disabled. Use the key or key to specify the 32-
ページ19に含まれる内容の要旨
Format Hard Disk? Press on the “MENU” key to pop up “Main Menu”. Use key to move the highlight and select “System Settings”. Press on the key to enter “System Settings” menu and select “Format Hard Disk”. Select Format Hard Disk, then press Enter key Press on the “left” key to proceed Format HDD and press Enter key to confirm. 18
ページ20に含まれる内容の要旨
Change DVR Serial Number Press on the key to pop up Main Menu and use the key to move the highlight. Select “System Settings” and press on the key to enter System Settings menu. Select “Display Settings” and press on key. Use the right key to select DVR serial number Use the key to move around and use the key to specify each item Use the key to highlight the “Save” button and press on the key to pop up “System Settings” menu. Press on the “MENU” key to end the setup, 19
