ページ13に含まれる内容の要旨
overview monitor Available after switching to Monitor mode by pressing the [monitor ] button on the remote control. auto id reset Selects the screen status automatically ． Initializes the ID value to 01. p.mode Selects the screen mode ． ! power monitor Turns the monitor power on/off ． Activates the monitor function. numBer [0~9] Changes the system ID. id Sets the ID. Select 2 digits from 0 ~ 9 while pressing the ID Key. +/- mute Adjusts the audio volume ． Mutes the audio out. menu Displays the
ページ14に含まれる内容の要旨
installation Please be noticed with the followings before you use the product. ~ Do not use the product outdoor. ~ Do not spill water or liquid in the connection part of the product. ~ Do not impose the system to excessive shock or force. ~ Do not pull out the power plug forcefully. ~ Do not disassemble the product on your own. ~ Do not exceed the rated input/output range. ~ Use a certifi ed power cord only. ~ For the product with an input ground, use a grounded power plug. checKing the instaLL
ページ15に含まれる内容の要旨
instaLLation racK instaLLation Loosen the screws on both sides (4 screws on each side) and install the Bracket-Rack as shown in the fi gure, and then fasten the screws on both sides (4 screws on each side). ` Fix the screws not to be loosened by vibrations. ! hdd addition You can install additional HDDs. Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product damage. Please consult your provider for further information on HDD installation
ページ16に含まれる内容の要旨
installation adding a hdd ` Make sure to unplug the power cord from the wall outlet before proceeding with the installation. M ` Number of HDDs to install : SHR-7082/7162/8082/8162 : Default 1 HDD + Up to 4 HDDs added SHR-7080/7160/8080/8160 : Default 1 HDD + Up to 5 HDDs added ` By factory default, the master unit is equipped with one HDD. The following instructions are when you have installed the maximum number of HDDs on the master unit. 1. First, loosen the screws in the left and right side
ページ17に含まれる内容の要旨
instaLLation . When the installation of additional HDDs is done, insert the lower and upper brackets into the DVR Upper Bracket and fi x them with the provided screws. Lower Bracket ! . When the installation of additional HDDs is done, connect the power cable and connect the HDD signal cables (SATA Cable) to connectors ~ on the main board. ` You can check the HDD map directly on the DVR. Refer to “S St to or ra ag ge e D De ev viic ce e > H HD DD D M Ma ap p” ”.. ((P Pa ag ge e
ページ18に含まれる内容の要旨
installation . Install a HDD (x1) on the lower bracket and fi x it with screws. Upper Bracket . Install HDDs (x3) on the upper bracket and fi x them Add with screws. Add Add Lower Bracket Installed by default Add . When the installation of additional HDDs is done, insert the lower and upper brackets into the DVR Upper Bracket and fi x them with the provided screws. Lower Bracket . When the installation of additional HDDs is done, connect the power cable and connect the HDD data cables
ページ19に含まれる内容の要旨
connecting with other device connecting with other device ` The following figures are based on Model SHR-8162. M connecting the video, audio, and monitor ! LOOP OUT AUDIO IN SPOT VIDEO IN AC 100-240V~IN NETWORK USB 2.0 AUDIO OUT CONSOLE RS-232 SATA VIDEO OUT (composite) RS-485 / ALARM VIDEO OUT HDMI (VGA) connecting the networK connecting to internet through ethernet (10/100/1000Baset) RJ45 Ethernet Cable (Direct Cable) Back Bone Hub/Switcher Hub/Switcher Windows NET-i English _19 00769B_SHR-81
ページ20に含まれる内容の要旨
connecting with other device connecting to internet through adsL RJ45 Ethernet Cable (Direct Cable) Phone(ADSL) Line ADSL MODEM Hub/Switcher Windows NET-i connecting the usB 1. There are two USB ports at the front and one at the back of the product. . You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port. . If a USB HDD is connected to the system, recognition and settings are available in “menu > setting the device > storage device”. (Page 43) . This product suppo
ページ1に含まれる内容の要旨
SHR-7080/7082/7160/7162
SHR-8080/8082/8160/8162
8 Channel/16 Channel DVR
User’s Manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please
register your product at
www.samsungsecurity.com
00769B_SHR-8162_ENG-NEW.indb 1 2008-12-04 오전 10:13:18
ページ2に含まれる内容の要旨
overview Features This DVR (Digital Video Recorder) employs MPEG-4 video encoding for 8 or 16 channels of camera input and G.723 audio encoding for 16 channels, and supports simultaneous hard disc recording and playback. And also it supports network connectivity, providing remote monitoring from a remote PC by transferring video and audio data. ~ Provides convenient User Interface ~ 8/16 CH Composite Input Connectors ~ Supports CIF(S)/Half D1(M)/Full D1(L) recording formats ~ NTSC/PAL Compati
ページ3に含まれる内容の要旨
overview important saFety instructions Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. ! 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instruction
ページ4に含まれる内容の要旨
overview BeFore start This user’s manual provides Information for using DVR such as brief introduction, part names, functions, connection to other equipment, menu setup, and the like. You have to keep in mind the following notices: ~ SEC retains the copyright on this manual. ~ This manual cannot be copied without SEC’s prior written approval. ~ We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of instructions mentioned in this man
ページ5に含まれる内容の要旨
overview standards approvals ` This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 M of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
ページ6に含まれる内容の要旨
overview contents 2 Features overview 3 Important Safety Instructions 4 Before Start 6 Contents 2 8 Part Names and Functions (Front) 10 Part Names and Functions (Rear) 12 Remote Control 14 Checking the installation environment instaLLation 15 Rack Installation 15 HDD Addition 14 19 Connecting the Video, Audio, and Monitor connecting with other device 19 Connecting the Network 20 Connecting the USB 20 Connecting External SATA HDD 19 21 Connecting POS Device 21 Connecting the Alarm Input/Output
ページ7に含まれる内容の要旨
overview 68 Introducing Web Viewer weB viewer 69 Connecting Web Viewer 71 Using Live Viewer 77 Using Search Viewer 68 81 Viewer Setup 91 About ! 92 SEC Backup Viewer BacKup viewer 92 94 Product Specification appendix 97 Product Overview 98 Default Setting 101 Troubleshooting 94 103 Open Source License Report on the Product English _ 00769B_SHR-8162_ENG-NEW.indb 7 2008-12-04 오전 10:13:23
ページ8に含まれる内容の要旨
overview part names and Functions (Front) 7080/8080 1 10 7160/8160 1 10 7082/8082 1 10 9 7162/8162 1 10 9 _ overview 00769B_SHR-8162_ENG-NEW.indb 8 2008-12-04 오전 10:13:28
ページ9に含まれる内容の要旨
overview Part Names Functions ALARM : Lights on when an event occurs. HDD : Displays the normal access to HDD. Upon access to HDD, LED repeats on and off. LED Indicator NETWORK : Displays both network connection and data transfer status. BACKUP : Displays when Backup is in progress. REC : Lights on when recording is in progress. ! PTZ : Sets PTZ Mode ON/OFF. ZOOM(TELE) : Sets the screen to the x2 digital zoom. Runs the TELE function in the PTZ Mode. FREEZE(WIDE) : Runs the FREEZE functio
ページ10に含まれる内容の要旨
overview part names and Functions (rear) 7080/7082 r ear 1 9 10 11 1 1 1 7160/7162 r ear 1 9 10 11 1 1 1 8080/8082 r ear 1 9 10 11 1 1 1 8160/8162 r ear 1 9 10 11 1 1 1 10_ overview 00769B_SHR-8162_ENG-NEW.indb 10 2008-12-04 오전 10:13:35
ページ11に含まれる内容の要旨
overview Part Names Functions VIDEO OUT Composite Video Signal Output Port (BNC type connector). AUDIO OUT Audio Signal Output Port (RCA jack). VGA VGA Video Signal Output Port. HDMI HDMI connector port. Audio input signal port (RCA Jack) and port for optional audio extension cable. ! AUDIO IN SHR-716x/816x (Audio 5~16CH) SHR-808x/708x (Audio 5~8CH) USB USB connector port. SATA 1/2 Ports used for external storage device connections. (SATA HDD) NETWORK NETWORK connector port. A live screen out
ページ12に含まれる内容の要旨
overview remote controL dvr Available after switching to DVR mode by pressing the [dvr ] button on the remote control. search BacKup Displays the search menu ． Displays the Backup Menu. open/cLose Opens or closes the CD tray. mode Changes the screen mode ． dvr Activates the DVR function. power Displays the Exit pop up screen ． + numBer [0~ 10] Used as the numeric input keys, or displays a single channel ． id Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key. skip B
