ページ1に含まれる内容の要旨
Cyber 2S1P PCIe
Quick Installation Guide
Introducing the Cyber 2S1P PCIe
The Cyber 2S1P PCIe high-speed serial I/O card
provides two 9-pin serial ports and one parallel
port.
Key Features and Benefits
• Adds 2 RS-232 9-pin serial ports and 1
ECP/EPP parallel port to your PCIe enabled
system
• Compliant with PCI Express Base
Specification, Revision 1.1
• Supports ECP, EPP and Buffered SPP
parallel port modes
System Requirements
• PCI Express enabled system with an
available PCI Express slot
®
• W
ページ2に含まれる内容の要旨
Package Contents • Cyber 2S1P PCIe board • 2-Port DB9 serial port cable • Driver CD • Quick installation guide Layout 2-Port DB9 serial port cable Stripe Parallel port Figure 1: Board Layout Note: When connecting the 2-Port DB9 serial port cable, position the ribbon cable(s) so that the stripe is on the side closest to the parallel port. See Figure 1. 2
ページ3に含まれる内容の要旨
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the pow
ページ4に含まれる内容の要旨
Skip this step if you don't need any serial ports. 6. To install the card, carefully align the card's bus connector with the selected PCIe slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 7. Replace the slot bracket holding screw to secure the card. 8. Mount the second serial port and secure it with the slot bracket holding the screw. Skip this step if you don't need any serial ports. 9. Replace the computer cover and reconnect the power cord. Driver Ins
ページ5に含まれる内容の要旨
3 . Insert the driver CD. Right click PCI Parallel Port, click Update Driver Software. 4. Click Browse my computer for driver software. For 32-bit: Type D:\32bit, then click Next. (Change D: to match your CD-ROM drive) For 64-bit: Type D:\64bit, then click Next. (Change D: to match your CD-ROM drive) 5. At Windows has successfully updated your driver software, click Close. 6. Right click PCI Serial Port, click Update Driver Software. 7. Repeat steps 4-5. 8. Right click PCI Serial Port, click U
ページ6に含まれる内容の要旨
3. Click Don't search online. Skip this step and go directly to step 4 if not prompted. 4. Click I don't have the driver disc. Show me other options. 5. Click Browse my computer for driver software (advanced). For 32-bit: Type D:\32bit, then click Next. (Change D: to match your CD-ROM drive letter) For 64-bit: Type D:\64bit, then click Next. (Change D: to match your CD-ROM drive letter) 6. At The sofware for this device has been successfully installed, click Close to complete the installation
ページ7に含まれる内容の要旨
3. Insert the driver CD, check Include this location in the search, uncheck the other box. For 32-bit: Type D:\32bit, then click Next. (Change D: to match your CD-ROM drive letter) For 64-bit: Type D:\64bit, then click Next. (Change D: to match your CD-ROM drive letter) 4. Click Finish to complete the installation. Windows Server 2003 (32-/64-bit) 1. At the Found New Hardware Wizard, select No, not this time, click Next. Skip this step and go directly to step 2 if not prompted. 2. Select Instal
ページ8に含まれる内容の要旨
For 64-bit: Type D:\64bit, then click Next. (Change D: to match your CD-ROM drive letter) 4. Click Finish to complete the installation. Windows Server 2008 (32-/64-bit) 1. At Found New Hardware window, click Locate and install driver software (recommended). 2. Click Don't search online. Skip this step and go directly to step 3 if not prompted. 3. Click I don't have the disc. Show me other options. 4. Click Browse my computer for driver software. 5. Insert the driver CD. For 32-bit: Type D:\32b
ページ9に含まれる内容の要旨
To Verify Windows Installation 1. Check in Device Manager to verify installation. For Windows 7: Right click Computer, click Manage, then click Device Manager. For Windows Vista: Right click Computer, click Manage, click Continue, then click Device Manager. For XP / Server 2003: Right click My Computer, click Manage, then click Device Manager. For Server 2008: Right click Computer, click Manage, double click Diagnostics, click Device Manager. 2. Click on the + (plus sign) in front of Ports (COM
ページ10に含まれる内容の要旨
1. From the Device Manager window double click Ports (COM & LPT), then double click PCIe to.... port. 2. Click Port Settings tab, then click Change Port Number. 3. Click the down arrow next to the COM Port number box, select a COM port that is not in use. Click OK, OK. Close Device Manager to save the changes. Changing Parallel Port Address (LPT) Some parallel devices need a specific parallel port in order to work. If your parallel device works properly, do not change this setting. 1. From th
ページ11に含まれる内容の要旨
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product. This warranty covers the original purchaser and guarantees the p
ページ12に含まれる内容の要旨
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufac
