ページ1に含まれる内容の要旨
TOSHIBA
Storage Device Division
DVD-RAM
DRIVE
SD-W2002
Installation Instructions
with VOB InstantWrite
and
TM
CyberLink PowerDVD Software
VERSION 3.0
JANUARY 2002
ページ2に含まれる内容の要旨
Limited Warranty Toshiba America Information Systems, Inc. Storage Device Division 9740 Irvine Boulevard, Irvine, California 92618 1-949-457-0777 What does my limited warranty cover? Toshiba America Information Systems, Inc. (“Toshiba”) warrants the Toshiba Storage Product (“Product”) you have purchased from Toshiba or from a Toshiba authorized dealer is free from defects in materials or workmanship under normal use during the warranty period. This limited warranty extends only to the original p
ページ3に含まれる内容の要旨
Disclaimer and limitation of remedy ALL OTHER EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND/OR NONINFRINGEMENT OF THIRD PARTY RIGHTS, ARE HEREBY DISCLAIMED. TOSHIBA EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE TERM OF THIS EXPRESS LIMITED WARRANTY. SOME COUNTRIES, STATES OR JURISDICTIONS DO NOT
ページ4に含まれる内容の要旨
Table of Contents Kit Packaging .............................................................................................. 1 System Requirements .................................................................................. 1 Setting Jumpers ........................................................................................... 2 Connecting Cables ....................................................................................... 3 Completing Installation.........................
ページ5に含まれる内容の要旨
Congratulations on your purchase of a Toshiba DVD-RAM drive and Kit. The following information will help you in the simple installation of your new DVD- RAM drive. CHECKINGYOUR KIT PACKAGING Please unpack your DVD-RAM kit, and assure that you have the following items: ! Toshiba SD-W2002 DVD-RAM Drive ! Blank Media - Single Sided/Type 1 DVD-RAM ™ ! CyberLink PowerDVD Software ! VOB InstantWrite Software CD ! DVD-RAM Installation Instructions (this manual) ! Quick Start Guide ! Mounting screws (4
ページ6に含まれる内容の要旨
The following steps must be performed to properly install your DVD-RAM. ● Set drive’s jumpers ● Connect audio cable ● Attach IDE BUS cable ● Connect power cable ● Mount DVD-RAM ™ ● Install CyberLink PowerDVD software (used for viewing DVD movies) ● Install VOB InstantWritesoftware (used for recording CDs) SETTING JUMPERS The mode select jumpers are six (6) straight angle pins located on the rear of the DVD-RAM. By placing a jumper on the pins, you can select the following func- tions: CS: – Driv
ページ7に含まれる内容の要旨
1. Remove computer cover and faceplate if required (refer to your computer system’s manual for removal information). 2. If the DVD-RAM is replacing a CD-ROM, disconnect all connectors and re- move the CD-ROM presently installed in your system. 3. Your Toshiba DVD-RAM can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) 4. Carefully start sliding the DVD-RAM into the opening with the disc tray facing the front of the compu
ページ8に含まれる内容の要旨
cable (side with red stripe) is connected to pin 1 on the drive. • If the DVD-RAM is the only drive connected on the secondary IDE BUS cable: connect drive to the last set of pins on IDE BUS cable. If there is a device (i.e. CD-ROM) connected to the secondary IDE BUS cable: connect DVD-RAM to the open middle connector . The DVD-RAM drive should then be jumpered to SL (slave) position. If the DVD-RAM is to be the slave on the Primary BUS: connect the DVD-RAM to the open connector on the primar
ページ9に含まれる内容の要旨
COMPLETING INSTALLATION After you have connected all the necessary cables, push the DVD-RAM com- pletely into the computer’s drive slot. Mount the drive per your computer’s in- structions using the screws included in your kit. If you are using other screws, assure that the screw length does not exceed 3±0.5mm (measured from outside surface of side or bottom of DVD-RAM to tip of screw). Replace the computer cover and all outer screws. ATAPI CD/DVD Software Driver: Toshiba’s DVD-RAM drives do not
ページ10に含まれる内容の要旨
DVD-RAM FRONT PANEL The photo below illustrates the following features of the SD-W2002 DVD-RAM’s front panel: Emergency Eject Hole: The emergency eject hole is to be used only when the DVD tray will not open when the Load/Unload button is pressed. Insert solid bar (i.e. paper clip) into hole, applying gentle presure, until tray opens. Do not use Emer- gency Eject Procedure while the drive is in operation. Loading Tray: Load disc using tray or recording cartridge Load/Unload Button: Used to open
ページ11に含まれる内容の要旨
OPERATING THE DVD LOADING TRAY To open the DVD loading tray, just press the Load/Unload button. After inserting or removing a disc or recording cartridge, press the Load/Unload button again. You must use a DVD-RAM recording cartridge when recording DVD-RAM media. Vertical Disc Installations When placing a disc into a DVD-RAM drive that has been mounted vertically, be assured that the disc in installed under the two front tabs. DVD-RAM MEDIA After installing the VOB and CyberLink software your s
ページ12に含まれる内容の要旨
SPECIFICATIONS DVD CD DATA CAPACITY 2,048bytes/block mode 1: 2,048bytes/block mode 2: 2,336bytes/block ROTATIONAL DVD-RAM (2.0): 1,380 - 3,300 CD-ROM, CD-R: 5,100 SPEED (RPM) 2,100 - 3,300 CD-RW: 3,400 DVD-RAM (1.0): 1,080 - 2,400 Video CD: 900 - 2,000 DVD-ROM (single): 2,400 CD-DA: 1,800 - 4,200 DVD-ROM (double): 3,800 DVD-R,DVD-RW: 1,100 - 2,800 SUSTAINED DATA DVD-RAM(2.1) 2,704 mode 1: 1,557 - 3600 TRANSFER RATE DVD-RAM (1.0) 1,352 mode 2: 1775 - 4,140 (kbytes/sec) DVD-ROM: 2,812 - 6,760 ACCE
ページ13に含まれる内容の要旨
9
ページ14に含まれる内容の要旨
460020-C0 P/N 460020-C0
