ページ1に含まれる内容の要旨
DMR-EZ47 Firmware Installation Instructions
Table of Contents
Table of Contents ............................................................................................. 1
1 Firmware History.............................................................................................. 2
1.1 Applicable Models ........................................................................................ 2
1.2 Purpose...........................................................................
ページ2に含まれる内容の要旨
1 Firmware History 1.1 Applicable Models DMR-EZ47, DMR-EZ475 Includes models with suffix K, S, V, VK, VP, or VS 1.2 Purpose UJ-225 Improved playback DVD+R media which was recorded by SONY DVD Recorder. Optimization of track jump control for CD-RW. Improvement of recording quality for DVD-R DL. UJ-217 Enhances Closed Captioning display. Enables the unit to the download the New V-Chip/Regional Rating Table (RRT). UJ-205 Modification to improve VHS Timer Recording.
ページ3に含まれる内容の要旨
2 Download Firmware 1) Left click on the DOWNLOAD icon for the DMR-EZ47 Firmware. - DMR-EZ47, DMR-EZ475 DVD Recorder Firmware 2) Left click on SAVE. The file name displayed should be PANA_DVD.FRM. 3) Left click on DESKTOP, and then left click on SAVE. NOTE: The PANA_DVD.FRM file will be placed on the DESKTOP. DMR-EZ47 DVD Recorder Firmware Installation Instructions Page 3 of 8
ページ4に含まれる内容の要旨
3 Burn Firmware Use one of the below procedures to burn firmware to a CD-R disc. 3.1 Windows® OS CD Writing Program 1) Insert a blank CD-R disc into a CD Burner Drive installed in or attached to the computer. 2) If the below (or similar) screen appears (Windows XP), left click on CANCEL. 3) Right click on the PANA_DVD.FRM file on the DESKTOP, mouse over SEND TO, and then left click on the CD BURNER DRIVE. 4) If the below screen appears, left click on YES. NOTE: T
ページ5に含まれる内容の要旨
5) Lift click on the YOU HAVE FILES WAITING TO BE WRITTEN TO THE CD icon in the SYSTEM TRAY. 6) Left click on WRITE THESE FILES TO CD. 7) Type a name for the CD, check the CLOSE THE WIZARD AFTER THE FILES HAVE BEEN WRITTEN check box, and then left click on NEXT. NOTE: The below screen will appear during the burning process. 8) After the PANA_DVD.FRM file has been burned to the CD, the disc should automatically eject from the CD Burner Drive. If it doesn’t, manual
ページ6に含まれる内容の要旨
3.4 Dragging & Dropping If an icon for the CD Burner Drive has been placed on the DESKTOP, left click on the firmware file, hold the left mouse button down, drag the file to the CD Burner Drive icon and release the left mouse button. If using the Windows XP operating system, use procedure from STEP 5 of SECTION 3.1 on PAGE 5 of 8. DMR-EZ47 DVD Recorder Firmware Installation Instructions Page 6 of 8
ページ7に含まれる内容の要旨
4 Install Firmware CAUTION: Do not turn the DVD Recorder OFF or press any buttons on the DVD Recorder while the firmware update is in progress. 1) Power the DVD Recorder on. 2) Press the [OPEN/CLOSE] button to OPEN the disc tray. 3) Place the CD-R with the firmware update into the disc tray with the label side facing up. 4) Press the [OPEN/CLOSE] button to CLOSE the disc tray. NOTE: If the firmware version in the unit is the same or higher than the firmware CD, UNSUPPORT ma
ページ8に含まれる内容の要旨
When the DVD Recorder is powered back on, the FIRST TIME SETUP screen should be displayed. 9) Follow the on-screen prompts to complete the FIRST TIME SETUP. DMR-EZ47 DVD Recorder Firmware Installation Instructions Page 8 of 8
