ページ1に含まれる内容の要旨
DVD-Video Player DVD963SA
DVD963SA /001 /171 /691
CL 26532105_000.eps
280802
Contents Page Contents Page
1 Technical Specs and Connection Facilities 2 8 Alignments (Not Applicable) 77
2 Safety Instructions, Warnings, and Notes 3 9 Circuit Descriptions 77
3 Directions for Use 4 List of Abbreviations 86
4 Mechanical-, Dismantling Instructions, and Service IC Data 87
Hints 18 10 Spare Parts List 91
5 Diagnostic Software, Trouble Shooting and Test
Instructions 21
6 Block-, Wiring Diagram and Testpo
ページ2に含まれる内容の要旨
Technical Specifications and Connection Facilities EN 2 1. DVD963SA 1. Technical Specifications and Connection Facilities Specifications PLAYBACK SYSTEM DVD Video AUDIO PERFORMANCE (Without upsampling) SACD multi channel and SACD stereo DA Converter 24 bits Video CD & SVCD DVD fs 96 kHz 4 Hz - 44 kHz CD (CD-Recordable and CD-Rewritable) CD/Video CD fs 44.1 kHz 4 Hz - 20 kHz MP3 CD S-Video CD fs 48 kHz 4 Hz - 22 kHz fs 44.1 kHz 4 Hz - 20 kHz Signal-Noise (1kHz) < -120 dB TV STANDARD (PAL/50Hz) (N
ページ3に含まれる内容の要旨
Safety Instructions, Warnings and Notes DVD963SA 2. EN 3 2. Safety Instructions, Warnings and Notes 2.1 Safety Instructions 2.2 Warnings 2.1.1 General Safety 2.2.1 General Safety regulations require that during a repair: All ICs and many other semi conductors are susceptible to • Connect the unit to the mains via an isolation transformer. electrostatic discharges (ESD, symbol ). Careless Replace safety components, indicated by the symbol , handling during repair can reduce life drastical
ページ4に含まれる内容の要旨
Mechanical-, Dismantling Instructions, and Service Hints EN 18 4. DVD963SA 4. Mechanical-, Dismantling Instructions, and Service Hints 4.1 Dismantling Instructions Figure 4-1 Dismantling Instructions DISMANTLING INSTRUCTIONS See exploded view of DVD963SA for item numbers Mounting TopCover 300 Remove 7 screws 305. Lift cover from rear side to Dismounting remove. Front cabinet 002 DVD Module 146 Double Scart board 1003 P-scan board 1004 Power supply un
ページ5に含まれる内容の要旨
Mechanical-, Dismantling Instructions, and Service Hints DVD963SA 4. EN 19 4.2 Exploded View Figure 4-2 Exploded View CL 26532105_003.eps 270802
ページ6に含まれる内容の要旨
Mechanical-, Dismantling Instructions, and Service Hints EN 20 4. DVD963SA 4.3.3 ComPair 4.3 Service Hints For assistance with the repair process of the monoboard an 4.3.1 Switched Mode Power Supply electronic fault finding guidance has been developed. This program is called ComPair. The power supply unit has to be replaced in case of failure. The This ComPair program is available on CDROM. schematic provided in the manual is only for information and no The version of the CDROM for repair of
ページ7に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 21 5. Diagnostic Software, Trouble Shooting and Test Instructions 5.1.2 Contents of Dealer Script 5.1 Dealerscript The dealer script executes all diagnostic nuclei that do not 5.1.1 Purpose of Dealer Script need any user interaction and are meaningful on a standalone DVD player. The dealer script can give a diagnosis on a standalone DVD The nuclei called in the dealer script are the following (the player, no other equ
ページ8に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 22 5. DVD963SA Press the OPEN/CLOSE key to proceed to the next test. 5.2 Player Script 5.2.4 Survey 5.2.1 Purpose of Player Script The Player script will give the opportunity to perform a test that Press 2 keys simultaneously will determine which of the DVD player's modules are faulty, to + read the error log and error bits and to perform an endurance Connect to mains loop test. To successfully perform the test
ページ9に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 23 5.3 Display PCB KEY ID KEY 5.3.1 Display Test 0 PLAY 1 STOP The display test is performed by nucleus DispDisplay. By 2 OPEN/CLOSE putting a serie of test patterns on the local display, the local display is tested. To step through all different patterns, the user 3 STANDBY must either press OPEN/CLOSE (pattern is ok) or STOP 4 NEXT (pattern was incorrect) to proceed to the next pattern. The 5 PREVIOUS display of pat
ページ10に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 24 5. DVD963SA pressed the PLAY key. Pressing the PLAY key, before pressing a key on the remote control, gives an error in the remote control test (note that the remote control test will also fail if a key on the remote control was pressed but no code was received). The remote control test does not check upon the contents of the received code, that is it will not be checked if the CL 96532065_013.eps 120799 received code match
ページ11に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 25 The test can be left by pressing the PLAY key for more than 5.4 Mono PCB Digital Part one second. 5.4.1 Picture Test 5.4.3 Sound 2 Test The picture test is performed by putting a predefined picture The second soundtest is performed by producing a sine sound (colour bar) on the display (nucleus VideoColDencOn), and (nucleus AudioSineOn). The signal can be stopped by pressing asking the user for confirmation. the ST
ページ12に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 26 5. DVD963SA 5.5 Basic Engine 5.5.1 Version Number In the basic engine tests, the version number of the Basic CL 16532162_043.eps Engine will be shown first, as the following example: 080102 Figure 5-25 By pressing OPEN/CLOSE the user confirms that the disc motor is running. Pressing STOP indicates the disc motor does CL 16532162_040.eps not work. Pressing PLAY proceeds to the next test, after a reset 080102 of the disc motor
ページ13に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 27 CL 16532162_046.eps CL 16532162_048.eps 080102 080102 Figure 5-28 Figure 5-31 The user can switch between the three different types of Only the identification number (decimal) representing set groove settings by pressing OPEN/CLOSE (forward to next errorbits will be shown. By pressing OPEN/CLOSE or STOP, nucleus in the list In-Mid-Out), or STOP (backward in the list In- the user can move forward or backward (respect
ページ14に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 28 5. DVD963SA After one loop cycle: Display the 3-digit module bits together Error with the last error code which occured in the loop test. The 4 Number Error name Explanation digits at the right side of the display (fig. 5-34) show the last 0103 S2B_SLEDGE Sledge could not be moved to error that was found during the loop test. The leftmost two digits home position. (54) of this code indicates which nucleus resulted in a fault
ページ15に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 29 SMA Error Codes Error Code Error name Explanation Error 0008 SP_CONTINU Sequence of sectors coming Number Error name Explanation ITYERROR from disc is incorrect. Reason: 0000 SMA_TIMEO Data coming from disc not in see SP_SYNCERROR UTERROR time. Reason: damaged disc or 0009 DMX_CONTI Sequence of sectors is incorrect. engine problem. NUITYERRO Reason: problem with buffer R RAM 000A LLD_ERROR An illegal audio format
ページ16に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 30 5. DVD963SA 5.6.3 Trade Mode When the player is in Trade Mode, the player cannot be controlled by means of the front key buttons, but only by means of the remote control. TO ACTIVATE TRADE MODE TO DEACTIVATE TRADE MODE POWER ON POWER ON DURING STOP MODE AND W/O DISC. DURING STOP MODE AND W/O DISC. PRESS REMOTE KEYS COMBINATION PRESS REMOTE KEYS COMBINATION <259> <259> PLAYER IS IN TRADE MODE WHEN PLAYE
ページ17に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 31 Table 5-2 Processor and peripherals Ref. # Reference Name Remark 80d DAC_ModeDSD Sets DAC to DSD mode Ref. # Reference Name Remark 81a DAC_LowPowerStandby Enable Low Power 6 PapChksFl Checksum FLASH On Standby 7a PapUclkAclkCdda uClock A_CLK in CD-DA 81b DAC_LowPowerStandby Disable Low Power mode Off Standby 7b PapUclkAclkDvd uClock A_CLK in DVD mode 82a DAC_UpsamplingFreq19 Sets Upsampling 7c PapUclkAclkDvd96 uClo
ページ18に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 32 5. DVD963SA Table 5-7 Log (Error logging in Nvram) Ref. # Reference Name Remark 84a Furore_High Sets Furore output pins Ref. # Reference Name Remark DSD_PCM0-9 to high 31 LogReadErr Read last Errors 84b Furore_Low Sets Furore output pins 32 LogReadBits Read errors Bits DSD_PCM0-9 to low 33 LogReset Reset Table 5-11 Karaoke (not available) Table 5-8 Miscellaneous Ref. # Reference Name Remark 48a KaraokeModeOff Switch Karaoke mode
ページ19に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 33 4 Basic Engine... MAIN > AUDIO > SINE WAVE MENU 5 Processor Peripherals... 1 Audio Sine On [21a] 6 Error Log... 2 Audio Burst On [21b] 7 Furore... 8 Miscellaneous... MAIN > AUDIO > DIGITAL PORTS MENU 1 No tets available First Level Submenus MAIN > AUDIO > EXT DAC BOARD MENU MAIN > AUDIO MENU 1. DAC Reset [79] 1 Mute... 2. I2C Test... 2 Pink Noise... 3. Clock... 3 Sine Wave... 4. Audio... 4 Digital Ports... 5. Low Power
ページ20に含まれる内容の要旨
Diagnostic Software, Trouble Shooting and Test Instructions EN 34 5. DVD963SA 4 NVRAM Modify [36] 3 Jump To Outside Grooves [42c] 5 NVRAM Read/Wr Test [15] 5.8 Nuclei Error Codes MAIN > MISCELLANEOUS > STATISTICS INFO MENU 1 Total Nr Of Times Tray Open [47a] In the following tables the error description of the error codes 2 Total Time Power On [47b] will be described. 3 Total Play-Time CDDA & VCD [47c] 4 Total Play-Time DVD [47d] 5.8.1 Audio Nuclei Third Level Submenus Error Error text MAIN > A
