ページ1に含まれる内容の要旨
Rear Observation System Package
Model RVMPKG2
Installation Manual
Features:
• Rearview Mirror with 4” LCD
• 2 Built in Speakers
• Rearview Camera Input
• Auxiliary Video Input
• Video System Auto Detection for PAL/NTSC
• Audiovox Navigation Input
• Cellular Phone Hands Free Input
• Hands Free Microphone Built-In
NOTE: Hands free feature may not operate with all cellular phones
and/or an adapter may be required. Rearview camera optional.
1
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Cautions!............................................................................................ 3 Preface ............................................................................................... 4 WARNING:.............................................................................. 4 Packing list ............................................................................... 4 1. Installation Instructions ................................................
ページ3に含まれる内容の要旨
Cautions! 1. The product is intended to assist in safe driving and to allow the driver to have a broader rearview while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to the country and their local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of yo
ページ4に含まれる内容の要旨
Preface There is a blind spot that exists at the back of a vehicle while the vehicle is in reverse. Equipped with a camera, this rearview mirror/monitor ensures safety by providing the driver with a clear and wide image of the area behind the vehicle while it is in reverse. WARNING: Backing up vehicle Do not back up vehicle while watching the mirror/monitor screen. Always look in the direction of vehicle motion. Use the mirror/monitor as an aid in safety confirmation. The distan
ページ5に含まれる内容の要旨
1. Installation Instructions (1) Mount the mirror/monitor onto the existing rearview mirror. a) Stick two adhesive foam backings on to the back of mirror in the two small rectangle indents. b) Take the two seven inch belts and slide them into the slots on the top rear of the mirror with grooved side of the belt facing down. Figure 1 c) Take the buckles and slide them into the lower slots on the rear of the mirror with the buckle facing down toward the seven-inch strap. Figure 2 N
ページ6に含まれる内容の要旨
Figure 3 e) Cut off the excess part of the 7-inch strap (2) Plug the Mitsumi connector from the Audiovox navigation monitor cable (part #112C3080) into the receptacle at the top backside of the mirror/monitor screen. Route the rest of the monitor cable to the Navigation computer. (3) Connect the control box monitor cable to the rearview mirror/monitor cable. Route the monitor cable behind the headliner of the windshield then down the A pillar behind the plastic shroud to the under dash
ページ7に含まれる内容の要旨
(2) Tear off the adhesive tape on the back of the hands free seat. Press tightly to seat on to the selected surface for 30 seconds till the two surfaces are tightly glued. NOTE: Make sure the two surfaces are glued tightly! (3) Clean a place on the back of the cell phone, keeping it dry. Remove the adhesive tape of the rounded metal sheet and stick it to the selected place on the back of the cell phone. NOTE: Do not attempt to move the phone within 24 hours after gluing. CAUTIO
ページ8に含まれる内容の要旨
3. Signal Inputs The signal input connections for the system include: (1) Rear Camera: By connecting rear camera with control box plug, users can see the rearview when the vehicle is in reverse. (2) Hands Free Jack: Put the hands free plug (3.5mm) into hands free jack and put the other side of plug into the headphone jack of the mobile phone. (If necessary, find a compatible adapter). (3) Navigation: The navigation signal is supplied via the connector plugged directly into t
ページ9に含まれる内容の要旨
Figure 5 Figure 6 4. Controls and Indicators Figure 6 illustrates the controls and indicators of the RVMPKG2 rear view mirror: A: Rearview mirror B: 4” LCD panel C: Hands free Microphone D: Brightness Control E: Power indicator (Red when ignition is on) F: Volume Control G: Switch 1 (see below) H: Switch 2 (see below) J: Switch 3 (see below) K: Speakers 9
ページ10に含まれる内容の要旨
L: Infra- RED receiver for M: 3-position switch for Navigation Navigation remote control voice command display timer on rear of mirror (30 sec., 150 sec., 300 sec.) N: 2-position switch for hands free microphone sensitivity High/Low select SW1, SW2 and SW 3: 1. Vehicle Reversing: SW 1: No function LCD automatically turns on SW 2: No function Rearview camera image appears on the mirror SW 3: No function 2. Vehicle driving: SW1: Turn o
ページ11に含まれる内容の要旨
3. Vehicle Parked: SW1: Used to turn the LCD on/off when using the AUX video and audio input. The parking brake must be engaged. SW2: Used to turn off and on the Navigation image. SW: 3 When pressed and held, the rear camera image appears on the mirror. When released the LCD will return back to its previous appearance. 11
ページ12に含まれる内容の要旨
Specifications General Power Supply 12VDC Power Consumption <12W Current Draw <500 mA Video Input 1Vp-p@ 75 Impedance Audio Input <=1V Audio Power Output 0.5W × 2 (16O) Operating Temperature -10°C to 60°C Overall Dimension 11W×3.75H×1.25D inch Display System Screen 4 ” TFT Color LCD Brightness 250 nit Contrast ratio 150:1 Viewing Angle Top-10°, Bottom 30°, Left 45°, Right 45° Resolution 480×234 Video Format PAL/NTSC auto detect Di
ページ13に含まれる内容の要旨
Maintenance Maintenance Your rearview mirror requires little care, however to maintain it in optimum condition follow the procedures below: 1. Keep your system away from excessive moisture, extreme heat or cold and magnetic fields. 2. Keep liquids away from the display. 3. Do not place external devices or other objects on the top of the mirror. Occasionally clean the surface of the mirror with a soft cloth moistened with water, or a window cleaner. Troubleshooting Table 1 Rearview
ページ14に含まれる内容の要旨
Table 2 Hands Free Phone Symptoms Solutions When the Hands Free Phone 1. Check the volume control knob Function is not working? whether the volume is set too low. 2. Check to see if the hands free cable plug to the phone hand set input jacket is properly connected. 3. Check whether the mobile phone hands free cable plug is properly connected to the control box. Figure 7 14
ページ15に含まれる内容の要旨
© 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6655 15
