ページ1に含まれる内容の要旨
Installation and Operation
HIGH DEFINITION
CAT 5 MULTIDRIVER POWER
Model 1171
™
High Defi nition Cat 5 MultiDriver
ページ2に含まれる内容の要旨
Installation and Operation Manual Model 1171 ™ High Defi nition Cat 5 MultiDriver Audio Authority and the Double-A Symbol are registered trademarks of Audio Authority Corp. AutoSelect is a trademark of Audio Authority. Copyright November, 2006, all rights reserved. Audio Authority Corporation Lexington, Kentucky 2 Audio Authority Model 1171 User Manual
ページ3に含まれる内容の要旨
Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
Getting Started • Read these instructions. • Unpack the product and its accessories. • Connect associated equipment (detailed instructions are found in the Installation Section). • Connect the product to a suitable power outlet using only the power supply provided. General Information The Model 1171, when combined with Model 9878 Cat 5 HDTV Connection Plates (Wallplates), enables HDTV signals to be distributed to multiple locations from a single source. Component video (YPbPr), analog stereo a
ページ5に含まれる内容の要旨
Audio Authority Model 1171 User Manual 5 Panel Descriptions Shown below are the front and back views of the 1171. POWER INDICATOR A green LED indicates the presence of power. HIGH DEFINITION POWER CAT 5 MULTIDRIVER CAT 5 OUTPUT JACKS COMPONENT VIDEO INPUTS ANALOG AUDIO DIGITAL AUDIO POWER Two Cat 5 cables must be connected Connect the source’s YPbPr Connect Source’s Use EITHER op- Use only the to each Model 9878 Wallplate output cables here Left and Right out- tical or coaxial included 18V
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
b. Connect all the signals available from the source unit: Component Video, Digital Audio and Analog Audio. Use either, but NOT BOTH Optical and Coaxial Digital Audio. 5. Wallplate Hookup. Caution! Do not connect A and B cables incorrectly. Do not apply system power until cables are tested and A and B connections are verifi ed. a. Pull two lengths of good quality Category 5e or 6 UTP cable from the main system to each Wallplate location. Carefully mark cables of each pair A and B; if they ar
ページ8に含まれる内容の要旨
Troubleshooting Guide Symptom Possible Cause(s) Picture has artifacts or appears sparkly Excessive cable length compensation Digital audio inoperative Neither or both optical and coaxial cables connected to source Does not repeat an IR command Some remotes cannot be processed by this sytem; IR Output not connected to IR system One Wallplate inoperative Cables swapped or plugs incorrectly pinned out Wallplates inoperative on one Bus cable loose or power supply unplugged Model 1171 or 11
ページ9に含まれる内容の要旨
Model 1171 Specifi cations Subject to change without notice. Video Parameters Signal Type Component (YPbPr) Video Formats 480i/p, 576i/p 720p, 1080i/p* Input Impedance 75 ohms Input Ground Isolation No Gain 1 Gain Accuracy 2% 3dB Bandwidth 100MHz Input Coupling AC S/N Ratio 60dB Max Gain/Equalization 1 Audio Parameters Format Digital/Analog Digital Audio Input Type Coaxial/Optical Input Impedance 75 ohms/50K ohms Min Load Impedance 75 ohms/10K ohms Multi-channel Digital Yes Frequency Response 1
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
Using Compatible IR Products Receiver Pinout Emitter Pinout Receivers are powered A passive emitter usually Infrared signals may be transmitted from by 12 volts on the sleeve has a two-conductor plug. contact of the 9878 any Wallplate location back to the 1171 Wallplate IR jack. IR output by connecting a compatible IR receiver to the Wallplate’s IR jack. The Wallplate provides 12V power to the IR Tip = Signal Tip = Signal Ring = Ground receiver; do not use IR receivers that Sleeve = Ground
ページ12に含まれる内容の要旨
