ページ1に含まれる内容の要旨
OWNER'S MANUAL
DC-1200FS Dust Collector with Floor Sweep
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708629 09/00
ページ2に含まれる内容の要旨
Important Information 2-YEAR JET offers a two-year limited LIMITED WARRANTY warranty on this product REPLACEMENT PARTS Replacement parts for this tool are available directly form JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box. REPLACEMENT PART WARRANTY JET Equipment & Tools makes ever
ページ3に含まれる内容の要旨
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this machine until proper training and knowledge has been obtained. 2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before servicing. 3. Do not use outdoors or on wet surfaces. 4. Do not allow to be used as a toy. Close attention is necessary when used near children. 5. Use only as described in this manual. Use only manufacturer’s recommen
ページ4に含まれる内容の要旨
Grounding Instructions Caution! This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and o
ページ5に含まれる内容の要旨
Specifications: DC-1200FS Stock Number....................................................................................................................708629 Blower Wheel Diameter........................................................................................................... 12" Sound Rating at 3 feet.....................................................................................................70-80 db Hose Diameter.............................................................
ページ6に含まれる内容の要旨
WARNING Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1. Warranty Card 1. Owner's Manual 1. Motor/Fan Assembly 5. Plastic Collector Ba
ページ7に含まれる内容の要旨
Assembly WARNING The dust collector must be disconnected from the power source during assembly (unplug). Failure to comply may result in serious injury! 1. Position the base on its side. Mount the two front, fixed casters on the base with four M6 M6x12 hex cap screws, four lock washers and four M6 flat washers, Figure 1. 2. Thread two hex nuts onto the caster shaft. Mount the rear, pivot casters and supporting bars to the base with two M10 flat washers, two M10 lock washers and two acorn nuts,
ページ8に含まれる内容の要旨
4. Press the smaller gasket (o-ring type), into the groove of the lower stand, where the inlet mounts. Attach the inlet (A, Fig. 4) to the lower stand inlet hole using six M6x12 pan head screws (B, Fig. 4). 5. Press the larger gasket (o-ring type) into the groove of the upper stand. Attach the upper stand to the lower stand using eight M6x20 cap screws, eight flat washers, eight lock washers and eight M6 hex nuts (A, Fig. 5). 6. Attach the handle (A, Fig. 6) to the support tubing using four M6x5
ページ9に含まれる内容の要旨
7. With the assistance of another person lift the motor housing onto the upper stand. 8. From the underside attach the motor housing to the upper stand using eight M6x16 hex head bolts and eight M6 lock washers (A, Fig. 7). 9. Attach the supporting bars (A, Fig. 8) to the motor housing using two M8x16 cap screws, two M8 flat washers, two M8 lock washers and two M8 hex nuts (B, Fig.8). 10. Screw a M6 hex nut on the dust bag hanger. Slip a M6 lock washer and a M6 flat washer onto the rod and screw
ページ10に含まれる内容の要旨
11. Slide the hook on the bag hanger through the top loop on the filter bag. Thread the retainer strap (A, Fig. 10) through the loops on the filter bag (B, Fig.10), and tightly secure to the upper housing. The retainer strap should be tight enough to provide a good seal. 12. Place the plastic collector bag onto the lower part of the housing. Place the two holes in the bag over the two bolts (C, Fig. 10) sticking out of the housing. The retainer strap should be placed, and tightened over the foam
ページ11に含まれる内容の要旨
3. Loosen the bag clamp, and remove the collector bag from the dust collector. Empty the contents into a fire proof metal container. 4. Attach a new bag using the bag clamp to secure. 5. Connect the machine to the power source. Note: Use the proper type hose to connect the dust collector to the machine being operated. Dryer vent hose is not acceptable for this purpose. Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Motor Make frequent inspecti
ページ12に含まれる内容の要旨
Parts Breakdown 12
ページ13に含まれる内容の要旨
Parts List for the DC-1200FS Index Part No. No. Description Size Quantity 1..........427001......................... Upper Housing....................................... .................................. 1 2..........427074......................... Pad........................................................ .................................. 2 3..........427002......................... Impellar Guard....................................... .................................. 1 4..........427058..
ページ14に含まれる内容の要旨
55........ST039304 .................... Tapping Screw.......................................M3.5x12................... 11 56........ST040200 .................... Tapping Screw.......................................M4x10...................... 28 57........TS-1550041 ................. Flat Washer...........................................M6 ........................... 13 58........TS-1550061 ................. Flat Washer...........................................M8 ............................. 6
ページ15に含まれる内容の要旨
Wiring Diagram 15
