ページ1に含まれる内容の要旨
1 HP MINI DUST COLLECTOR
31810
SET UP aND OPERa TINg INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVE THIS MaNUaL.
© ®
Copyright 2001, 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may no
ページ2に含まれる内容の要旨
3. Keep bystanders, children, and PRODUCT SPECIFICaTIONS visitors away while operating a Electrical Input 120V / 60 Hz / 1 HP power tool. Distractions can cause 3 Prong Power Plug you to lose control. Protect others 6’-5” Power Cord Length in the work area from debris such as Intake Diameter 4” OD chips and sparks. Provide barriers or Collection Capacity 13 Gallons Maximum Air Flow 660 CFM shields as needed. ELECTRICaL SaFETY SaVE THIS MaNUaL 1. grounded tools must be plugged You will
ページ3に含まれる内容の要旨
4. Do not expose power tools to rain 4. Remove adjusting keys or wrench- or wet conditions. Water entering es before turning the power tool a power tool will increase the risk of on. A wrench or a key that is left at- electric shock. tached to a rotating part of the power tool may result in personal injury. 5. Do not abuse the Power Cord. Never use the Power Cord to carry 5. Do not overreach. Keep proper the tools or pull the Plug from an footing and balance at all times. outlet. Keep
ページ4に含まれる内容の要旨
5. Store idle tools out of reach of chil- SPECIFIC SaFETY RULES dren and other untrained persons. 1. Wear aNSI-approved safety impact Tools are dangerous in the hands of eye goggles, hearing protection, untrained users. and a dust mask or respirator 6. Maintain tools with care. Keep cut- when operating this product. ting tools sharp and clean. Prop- 2. The Housing contains a high speed erly maintained tools with a sharp Impeller that can amputate fingers, cutting edge are less likely
ページ5に含まれる内容の要旨
Electromagnetic fields in close prox- remove the grounding prong imity to heart pacemaker could cause from the plug. Do not use the pacemaker interference or pacemak- tool if the power cord or plug er failure. is damaged. If damaged, have it repaired by a service facility 8. WARNING: This product contains before use. If the plug will not or, when used, produces a chemi- fit the outlet, have a proper cal known to the State of California outlet installed by a qualified to cause cancer
ページ6に含まれる内容の要旨
3. The tool must be plugged into an 7. Make sure the extension cord is prop- appropriate outlet, properly installed erly wired and in good electrical con- and grounded in accordance with all dition. Always replace a damaged codes and ordinances. The plug and extension cord or have it repaired by outlet should look like those in the a qualified electrician before using it. preceding illustration. (See 3-Prong 8. Protect the extension cords from Plug and Outlet.) sharp objects, excessive he
ページ7に含まれる内容の要旨
UNPaCKINg aSSEMBLY INSTRUCTIONS When unpacking, check to make sure NOTE: For additional information regard- all that all the parts listed in the Parts List ing the parts mentioned in the fol- near the end of the manual are included. lowing pages, refer to the assembly If any parts are missing or broken, please Diagram near the end of the man- call Harbor Freight Tools at 1-800-444- ual. 3353 as soon as possible. 1. Remove the Lock Washers (33a) and Nuts (34) from the Caster (25) Studs. 35 33
ページ8に含まれる内容の要旨
OPERaTINg INSTRUCTIONS INSPECTION, Ma INTENa NCE, aND CLEaNINg NOTE: For additional information regard- ing the parts mentioned in the fol- WaRNINg! Always make sure the Power lowing pages, refer to the assembly Switch is in its “OFF” position, and Diagram near the end of the man- unplug the Power Cord/Plug from its ual. 120 volt electrical outlet before per- forming any inspection, adjustments, 1. Turn the Power Switch off. Then, maintenance, or cleaning. plug the Power Cord Plug int
ページ9に含まれる内容の要旨
PLEaSE REaD THE FOLLOWINg CaREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEM
ページ10に含まれる内容の要旨
8 47 38 13 4 40 14 3 1 42 45 33 30 41 46 29 38 40 33 9 32 28 10 41 27 41 11 26 15 12 32 37 36 24 40 2 37 23 29 35 31 22 21 36 33a 34 19 18 37 25 17 44 28 16 aSSEMBLY DIagRaM SKU 31810 For technical questions, please call 1-800-444-3353. Page 10
ページ11に含まれる内容の要旨
LIMITED 1 YEaR / 90 Da Y WaRRaNTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Har- bor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that al
