ページ1に含まれる内容の要旨
's I
I Horsepower (continuous duty)
2 Horsepower (maximum developed)
650 C°FoM°
3450 R.P.M. (no _oad R.P.M.)
ST COLL
Mode_ No.
152.213361
C
CAUTION:
FOR YOUR OWN SAFETY; Read
and follow all of the Safety and
Operating instructions before
Operating this Dust Collector.
Customer Helpline
1-800-897-7709
Please have your Model No.
and Sedal No. available.
Sears, Roebuck and Co., Hoffman Estates, JL (}0179 U.S.A.
Part No. OR92136
Revision A
Espa5olpg. 21
ページ2に含まれる内容の要旨
SECTmON PAGE Warranty ..................................................................................... 2 Product Specifications ......................................................................... 2 Safety mnstructions ............................................................................ 3 Grounding mnstructions ......................................................................... 5 Specific Safety mnstructions for Dust Collectors ............................................
ページ3に含まれる内容の要旨
9, GENERAL SAFETY iNSTRUCTiONS ALWAYS WEAR EYE PROTECTION. Any power tool can throw debris into the eyes during opera- Operating a Dust Collector can be dangerous if safety tions, which could cause severe and permanent and common sense are ignored. The operator must be eye damage. Everyday eyeglasses are NOT safety familiar with the operation of the tool. Read this manual glasses. ALWAYS wear Safety Goggles (that to understand this Dust Collector. DO NOT operate this comply with ANSi standard Z8
ページ4に含まれる内容の要旨
21,EACHANDEVERY TmME,CHECK FOR DAM- The smaller the gauge number, the larger diameter of AGED PARTS PRmOR TO USmNGTHE TOOL, the extension cord, if in doubt of the proper size of an extension cord, use a shorter and thicker cord, An Carefully check all guards to see that they operate properly, are not damaged, and perform their undersized cord will cause a drop in line voltage resulting in a loss of power and overheating, USE intended functions, Check for alignment, binding or ONLY A 3-WIRE EXTEN
ページ5に含まれる内容の要旨
The motor supplied with your Dust Collector is a 120°volt, singb-phase motor, It is shipped wired for THINSTOOL MUST BE GROUNDED WHmLE mNUSE 120°volt application, Never connect the green wire to a TO PROTECT THE OPERATOR FROM ELECTRmC live terminal, See OPERATING DUST COLLECTOR SHOCK. section for directions on changing motor voltage, mNTHE EVENT OF A MALFUNCTmON OR BREAK- USE ONLY A 3-WIRE EXTENSION CORD THAT HAS DOWN, grounding provides the path of bast resistance A 3-PRONG GROUNDING PLUG AND A
ページ6に含まれる内容の要旨
12, SPECiFiC SAFETY iNSTRUCTiONS USE only as described in this manual, USE acces- sories only recommended by Sears, FOR DUST COLLECTORS 13, DO NOT pull the dust collector by the power cord, The operation of any Dust Colbctor can result in debris NEVER allow the power cord to come in contact being thrown into your eyes, which can result in severe with sharp edges, hot surfaces, oil or grease, eye damage, ALWAYS Wear Safety Goggbs (that com- ply with ANSi standard Z87,1) when operating the Dust 14
ページ7に含まれる内容の要旨
AVAILABLE ACCESSORIES Sears may recommend other accessories not Hsted in this manual Visit your Sears Hardware Department or see the Sears See your nearest Sears Hardware Department or Sears Power and Hand Tool CataUog for the following acces- Power and Hand Tool CataUog for other accessories, sories, Do not use any accessory unUess you have compUeteUy ITEM STOCK NUMBER read the Owner's ManuaUfor that accessory, 21376 30 micron filter bag (top) 21377 5 micron filter bag (top) 21378 PUasticcollec
ページ8に含まれる内容の要旨
UNPACKING AN{) CHECKING CONTENTS (Figure3) if any parts are missing, do not attempt to plug in the power cord and turn "ON" the Dust Collector, The Dust This Dust Collector will require a minimal amount of Collector can only be turned "ON" after all the parts assembly, have been obtained and installed correctly, Remove all of the parts from the shipping box and lay them on a clean work surface, Compare the items to figure 3, verify that all items are accounted for before discarding the shipping
ページ9に含まれる内容の要旨
Fig. 4 D_ G A A, 4-inch Untake Port B B, 4-inch FUexibUe Hose C, FHter Bag Hanger D, FHter Bag E, Collection Bag F Locking Band G, BUower and Motor AssemMy H, Side Support J L Base J, Caster
ページ10に含まれる内容の要旨
SiDE SUPPORT ASSEMBLY DO NOT assembb the Dust Colbctor until you are sure the tool IS NOT plugged in, MAKE CERTAIN THE DUST COLLECTOR IS 2, DO NOT assembb the Dust Colbctor until you are DISCONNECTED FROM THE POWER SOURCE. sure the power switch is in the "OFF" position, 3, Fig. 6 For your own safety, DO NOT connect the machine to the power source until the machine is completely assembled and you read and understand the entire Owner's Manual, SWIVEL CASTER TO BASE ASSEMBLY C MAKE CERTAIN THE DUST
ページ11に含まれる内容の要旨
MOTOR AND BLOWER 5, Figure 9 shows the motor and blower assembly attached to the side supports, TO BASE ASSEMBLY SUPPORT ASSEMBLY MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE. MAKE CERTAIN THE DUST COLLECTOR IS 1, Place motor and blower assembly and base on DISCONNECTED FROM THE POWER SOURCE. their side with intake port pointing towards base, Fig. 8 Fig. 10 C B B _B B_ A c A 2, Align the four hobs, two shown (A) on the top of both side supports (B) with four holes in the
ページ12に含まれる内容の要旨
4, FILTER AND COLLECTION BAG Place the second IocMng band through all the loops of the collection bag, similar to the filter bag, TO DRUM ASSEMBLY 5, Place the collection bag over the lower lip of the drum, Make certain the Hocking band is positioned MAKE CERTAmN THE DUST COLLECTOR ms in the lower recessed channel of the drum and DmSCONNECTED FROM THE POWER SOURCE. fasten champ secureiy to drum, Fig. 11 iNTAKE PORT CAP AND HOSE ASSEMBLY MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE PO
ページ13に含まれる内容の要旨
Fig. 14 ! FOROPERATOR SAFETY, keepfingersandaHH foreign objectsoutoftheintakeports,Therotating faninside theMowerhousing isaccessibHe through theintake portsandishazardous, DonotwearHoose cHothing or jeweHry, Makecertain thateachintakeportwhichisnot A beingusedorattached to a dustcoHHection systemis covered withanintakeportcap, CONNECTING TOOL TO POWER SOURCE B A separate eHectricaHcircuit shouHd be used for your tooHs,This circuit shouHd not be Hessthan #14 A, W, G, wire and shouHd be protected
ページ14に含まれる内容の要旨
HELPFUL HINTS: Belowaresometermsthatwiiihelpyouto understand andsetupyourDustCollector anddesign yourown , Alwaysrunthelargestappropriate diameter hose DustCollection System, asfaraspossible, Running asmaller diameter hose wiiigreatlyreducetheC,F,M, at thetool,yielding DustCollector- A machine usedto collectfinewood marginal dustcollection, dustandchips, Theuseof a lowratedmicronfilterandcollection bagcanincrease theeffectiveness ofyourdust DustCollectionSystem- Adustcollector connected collecto
ページ15に含まれる内容の要旨
C.F.M. REQUIREMENTS FORTOOLS Machine Minimum C.F._,_.Required Minimum Duct Diameter Band Saw (12 to 16qnch) 350 C,F,M, 4qnch BeWDbc Sander 450 C,F,M, 5qnch DrHUPress 350 - 400 C,RM, 4qnch Drum Sander (12 to 24qnch) 550 - 700 C,RM, 5qnch Fbor Sweep 350 - 400 C,RM, 4 to 5qnch Jointer (up to 8qnch) 350 - 400 C,RM, 4 to 5qnch Jointer (over 8qnch) 450 - 550 C,RM, 5qnch RadiaUArm Saw 450 - 600 C,RM, 5qnch Miter Saw 450 - 600 C,RM, 5qnch Router TaMe 200 C,F,M, 3qnch Scroll Saw 200 C,F,M, 3qnch Spindb S
ページ16に含まれる内容の要旨
Topurchase anyoftheDustCollection Accessories listedbelow, visityournearest SearsStore, VariousFittings: 21340 3=inch HoseCoupling 21341 4-inchHoseCoupling 21363 3=inch 90=degree Elbow 21364 4-inch90-degree Elbow 21365 3=inch Y=Fitting 21366 4-inchYoFitting 21367 3=inch T=Fitting 21368 4-inchToFitting HOSe: 21370 3-inch x lO-foot Flexible Hose 21371 3-inch x 25-foot Flexible Hose 21372 4-inch x lO-foot Flexible Hose 21373 4-inch x 25-foot Flexible Hose Blast Gates 21359 3-inch Blast Gate - Plast
ページ17に含まれる内容の要旨
Turnthepowerswitch"OFF" andunplugthepower airmaydamage insulation.Theoperator should always cordfromitspowersourcepriortoanymaintenance, weareyeprotection whenusingcompressed air. Alwaysmakesurethattheintakeportcapscovers the intakeportwhena hoseis notconnected tothedust Donotallowchipsanddusttoaccumulate underdust collector. collector.Keepareacleanandinsafeorder. CAUTION: DONOTUSEFLAMMABLE MATERIALS tocleanDustCollector. TheDustCollector hassealedlubricated bearings in themotorhousing thatdoesn
ページ18に含まれる内容の要旨
PORTABLE DUSTCOLLECTOR PARTS UST MODELNO.152.213361 Whenservicing, useonlyCRAFTSMAN replacement parts,Useof anyotherpartsmaycreatea HAZARD orcause product damage, Anyattempt to repair or replace electrical partsonthisDustCollector maycreatea HAZARD unlessrepairisdoneby aqualified servicetechnician, Repair serviceisavailable at yournearest SearsServiceCenter, AlwaysorderbyPARTNUMBER, notbykeynumber, Key No. PART No. Description Qty. Key No. PARTNo. Description Qty. 1 OR90652 HEX NUT 5/18-18 1 MOT
ページ19に含まれる内容の要旨
PORTABLE DUSTCOLLECTOR PARTS LmST MODELNO.152.213361 13 F 14 15 12 17 _-_- 18 19 28C 26 28D 29 35 42 43 19
ページ20に含まれる内容の要旨
NOTES 20
