ページ1に含まれる内容の要旨
(1,1) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM (1,1) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM
Installation instructions
DishDrawer®
NZ AU GB IE
DD60D models
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our
local website listed at the end of this document or contact you
ページ2に含まれる内容の要旨
Integrated DD60D Prefi nished Flat door DD60D Prefi nished L CD DD60D Integrated DD60D Prefi nished Flat door DD60D Prefi nished L CD DD60D (1,2) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM (1,2) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM 23 PRODUCT DIMENSIONS CABINETRY DIMENSIONS Installation diagrams for illustration purposes only Installation diagrams for illustration purposes only B C B N D I D A G K H C E E C L N G O A F M I J Product dimensions (mm) Cabin
ページ3に含まれる内容の要旨
(2,1) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM (2,1) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM 4 PARTS SUPPLIED Drain hose Drain hose Wire clip (2) Clamp (1) Top Phillips Rubber Moisture protection Hexagonal Prefinished toekick (1) support (1) joiner (1) mounting 16 mm washer for tape (1) socket (2) white or black brackets (2) screws (9) inlet hose (1) (to prevent moisture (long & short) damage) OPTIONAL If the Drain hoses supplied are not long enough to reach
ページ4に含まれる内容の要旨
(2,2) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM (2,2) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM Max. distance of Left hand Right hand hoses and cord from side side chassis edge Drain hose Left hand Right hand 2000 mm 1800 mm side side Inlet hose 1650 mm 1250 mm Power cord (excl. plug) 1650 mm 1650 mm
ページ5に含まれる内容の要旨
(1,1) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM (1,1) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM 6 ROUTE THE HOSES AND MOVE INTO THE CAVITY AA B If top mounting brackets are being Ensure hoses and cord used, ensure they’re securely fitted 2 are not kinked or twisted. before sliding product into cavity. optional optional (x2) 3 Loosen feet only and 3 OR take care when pushing 1 the product into the cavity that you do not bend the feet. 1 2 Tie together to avoi
ページ6に含まれる内容の要旨
(1,2) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM (1,2) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM 8 SECURE THE PRODUCT AND REFIT THE DRAWER A B B 3 The product has three Ensure the drawer clips on 5 pairs of mounting both sides are reset. optional C brackets: a pair of C optional brackets on the top (C) and max. 19 mm two pairs of formed brackets in the side of the chassis (A,B). Use at least two out of the three pairs to secure the product. Before refitt
ページ7に含まれる内容の要旨
750 - 882.5 mm 750 - 882.5 mm (2,1) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM (2,1) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM 10 PLUMBING AND DRAINAGE OPTIONS A DishDrawer® and Standpipe Ø 38 mm B DishDrawer® using sink trap with drain hose joiner 2 2 Waste Disposal (optional) Do not connect to If space is limited for fixing, push DishDrawer® hoses through drain hose support to required height max. 750- 750- 882.5 882.5 120 mm mm mm 1 38 mm 1 HIGHLOOP mi
ページ8に含まれる内容の要旨
(2,2) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM (2,2) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM 11 FINAL CHECKLIST 12 TROUBLESHOOTING Check all parts are installed. Excessive water remaining above the filter plate, after the rinse cycle Ensure product is level, securely fastened to the cabinetry and opens and closes Check for kinked drain hoses or blocked waste connection, high loop not freely. The DishDrawer® must be free to fully close with no resistance fr
