ページ1に含まれる内容の要旨
MEMO
2 WAY
VOLUME
MIC
CLOCK
ON/OFF
PLAY LINE 1
LINE 2
L1 L2
REPEAT
STOP
FORWARD
DELETE
2
Two-Line Digital
Answering System
with Time/Day Stamp 1772
Fold open this paper for information about
this product's installation and operation.
Please read Part 1 — Important Product
Information, included in this package.
Part 2
© Copyright 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in Mexico. Issue 1AT&T
848229241
ページ2に含まれる内容の要旨
INST ALLA TION Install the Batteries For One Two-Line Wall Jack For Two Single-L L1 OR L1/L2 jack TEL SET jack L TEL SET jack Power cord L1 OR L1/L2 jack Two-line wall jack Line 1 jac Two-line phone with Two-line phone single cord single cord 2 Plug one end of the line cord with clear INSTALL THE BATTERIES For two single-line phones plugs into the system jack labeled L2. 1 Plug the cord from the phone for Line 1 Open the battery door on the bottom of the Plug the other end of the cord into the i
ページ3に含まれる内容の要旨
INST ALLA TION ine Wall Jacks For Two Single-Line Phones For Two-Line Phone with Two Cords L1 OR L1/L2 jack L2 jack L2 jack TEL SET jack Power cord Power cord Power cord L1 OR L1/L2 jack Line 2 jack with dual Line 2 jack outlet adapter Two-line jack with Line 1 jack ck single jack adapter and dual outlet adapter e with Two-line phone with d two cords Two single-line phones 3 Plug the cord from the L2 jack on the 3 Hold down F or R until the CONNECTING THE POWER CORD system into the dual outlet a
ページ4に含まれる内容の要旨
IN CASE OF DIFFICUL TY If this answering system does not work LO BATT DISPLAYED OTHER PROBLEMS properly, try the following suggestions The batteries might be missing, low on ¥ If the system malfunctions, make sure before seeking repair assistance. power, or incorrectly installed. you have followed all the instructions in this manual to try to correct the problem. MESSAGE WINDOW IS BLANK ¥ If you cannot correct the problem, press SYSTEM DOES NOT DISCONNECT Make sure the power transformer is r.
ページ5に含まれる内容の要旨
ANSWERING SYSTEM OPERA TION ANNOUNCEMENT OPTIONS SELECT ANNOUNCEMENTS MESSAGE ALERT The Answering System 1772 lets you Set the Line 1 ANNC SELECT switch to You can set the system to beep every 15 record up to 4 different announcements — A, B, C, or AO to select the announcement seconds to notify you when you have new A, B, C, and AO. Each can be presented callers to Line 1 will hear. messages. Set the MSG ALERT switch to callers on either Line 1 or Line 2. You (under the cover) to ON. Set the
ページ6に含まれる内容の要旨
MEMO 2 WAY VOLUME MIC CLOCK ON/OFF PLAY LINE 1 LINE 2 L1 L2 REPEAT STOP FORWARD DELETE ANSWERING SYSTEM OPERA TION FORWARD/SKIP MESSAGES CALL SCREENING PRIORITY CALLING To skip to the next message, press F. The priority call tone is preset to 99. CALL INTERCEPT To skip part of a message (cue), hold Callers to whom you have given the Set the volume to 2 or above so you can down F for a few seconds, then Priority Calling Code will be able to hear a caller’s voice on the speaker. If you release i
ページ7に含まれる内容の要旨
ANSWERING SYSTEM OPERA TION A way From Home You can operate the answering system PLAY MESSAGES RECORD A MEMO while away from home using the telephone To play all messages on both lines, wait 1 Press 1* to record on Line 1 keypad (touch tone phone only), or voice- 4 seconds, or press 7. — OR — activated commands. To play all messages on Line 1, press 17. Press 2* to record on Line 2. To play all messages on Line 2, press 27. 2 Begin speaking after the beep. CONNECT WITH THE ANSWERING To play only
ページ8に含まれる内容の要旨
ANSWERING SYSTEM OPERA TION A way From Home 1 Dial your telephone number, listen for 7 After the last message plays, the system MEMORY FULL/NO ANNOUNCEMENT the announcement, and then remain announces “End of messages” followed If the system answers after 10 rings, and silent after the beep. by the prompt “Replay messages?” presents 2 beeps but no announcement, the system might be off for one or both lines, NOTE: If the system answers after 10 To replay all of the messages, say memory might be f
ページ9に含まれる内容の要旨
2 ANSWERING SYSTEM 1772 1 Dial telephone number and wait for system to answer. 2 Enter Remote Access Code. 3 Listen for messages — OR — Enter touch tone command. 4 Hang up to save messages. Your Remote Access Code _______ © 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico. Issue 1AT&T 848229274 2 ANSWERING SYSTEM 1772 1 Dial telephone number and wait for system to answer. 2 Enter Remote Access Code. 3 Listen for messages — OR — Enter touch tone command. 4 Hang u
ページ10に含まれる内容の要旨
OPTION PRESS Play messages 7, 17, or 27 Play only new messages 6, 16, or 26 Repeat message 2 Skip message 5 Delete selected message 3 Delete all messages 03, 13, or 23 Record announcement 14* or 24* Record memo 1* or 2* End a recording # Turn system on 00, 10, 20 Turn system off 88, 188 or 288 OPTION PRESS Play messages 7, 17, or 27 Play only new messages 6, 16, or 26 Repeat message 2 Skip message 5
