ページ1に含まれる内容の要旨
Quick reference guide
Chart
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
PROGRAM SELECTION START/RESUME BUTTON CANCEL/OFF BUTTON
BUTTON Push this button to start the selected program: the Push this button to switch off the cont
ページ2に含まれる内容の要旨
How to set water hardness in order to always assure the best cleaning results First time use Water hardness should be set only -Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. before the first wash or if water - Programs LEDs will indicate the water hardness setting. hardness has been changed -Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1. - Wait 30 seconds (control panel switches off
ページ3に含まれる内容の要旨
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Daily check Visual The rinse aid dosage can be indicator adjusted to the detergent used. 2 The lower the setting, the less rinse aid is dispensed (factory setting: position 4). If required, Press the button to open the open the cover B. Using a coin or similar cover B Add rinse aid object, turn the arrow to the (press the to the max. desired setting. After adjusting dedicated line ~
ページ4に含まれる内容の要旨
How to load UPPER RACK How to load the racks How to adjust upper rack height (if available). (depending on the model) B - Cutlery basket - half: can be placed in the upper rack A - Adjustable flaps: in horizontal position for It could be useful to lift up the upper rack to have when the “Half load/Multizone” option is selected. more space in lower rack or bring it down to load cups/long utensils. 4 The Grid (G) should be removed. long stem glasses. - Grasp and take out the two lateral handles
ページ5に含まれる内容の要旨
Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). 6 Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle The dishwasher door must be closed and the water tap open. To pause the program (e.g. if you want to insert an item
ページ6に含まれる内容の要旨
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes... Solutions... ...is not working/will not start - The appliance must be switched on. - Check the household circuit fuse if there is no power supply. - The dishwasher door doesn’t close. - Check if the dishwasher’s
ページ7に含まれる内容の要旨
What to do if... Crockery and cutlery... Possible causes... Solutions... ...salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up. ...have deposits: regeneration salt residue - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. - Not enough rinse aid
ページ8に含まれる内容の要旨
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1. Packi