ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
G GU UIID DE E F FO OR R U US SIIN NG G T TH HE E D DIIS SH HW WA AS SH HE ER R A AN ND D T TH HE E W WA AS SH HIIN NG G P PR RO OG GR RA AM MS S
ページ2に含まれる内容の要旨
Contents 1. Description of the controls________________________________16 2. Troubleshooting _______________________________________25 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complet
ページ3に含まれる内容の要旨
User instructions 1. Description of the controls 1.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on, programming, switch-off etc. procedures are only possible when the door is open. ON/OFF BUTTON 1 Pressing this button energises the appliance. SELECTED PROGRAM INDICATOR LIGHTS 2 Illumination of this light denotes the program selected and the occurrence of a fault (troubleshooting). PROGRAM SELECTION BUTTON 3 By pressing this button in sequence it is possible to
ページ4に含まれる内容の要旨
User instructions HALF LOAD BUTTON (on some models only) 8 Press this button to activate the half load wash option. HALF LOAD LIGHT (on some models only) 9 One of the two buttons illuminates to indicate that the half load wash option in the top or bottom basket has been selected. PROGRAM DELAY BUTTON (on some models only) 10 Press this button to delay the start of the program by up to 9 hours. 11 (on some models only) INFORMATION DISPLAY SETTING THE WASHING PROGRAM AND SWITCHING ON To select the
ページ5に含まれる内容の要旨
User instructions DURATION CONSUMPTION PROGRAMME, LOAD CROCKERY PROGRAM NUMBER & SYMBOL AND CUTLERY PROGRESS MINUTES WATER POWER (2) LITRES (1) KWh (2) _ Pans and dishes SOAK 1 Cold prewash 16' 6 awaiting a further wash Cold prewash Wash at 45°C Dishes with DELICATE 2 Cold rinse 75' 16 1,15 light dirt Rinse at 68°C Dry Cold prewash Wash immediately after Wash at 50°C ECO (*) 3 use for dishes with Cold rinse 140' 14 1,08 EN 50242 normal dirt Rinse at 68°C Dry Cold prewash Wash at 65°C Dishes with
ページ6に含まれる内容の要旨
User instructions TABLE FOR CERTIFICATION BODIES Reference standard EN 50242 Reference program ECO Load 14 place-settings Type of detergent B Amount of detergent 35 g Rinse aid setting Depending on the model 3/4 or 4/6 CANCELLING THE CURRENT PROGRAM • To cancel the currently selected program, open the door and hold down the PROGRAM SELECTION (3) button for a few seconds indicator lights 4 5 until the for programs and illuminate simultaneously (the word "end" is displayed on the window). • Cl
ページ7に含まれる内容の要旨
User instructions 1.2 Washing programs Before starting a washing program make sure that: • The water supply tap is open. • The correct amount of detergent has been added to the dispenser. • The baskets have been correctly loaded. • The spray arms are able to rotate freely and without obstruction. • The dishwasher door is securely closed. SELECTING HALF LOAD WASH (on some models only) This function is ideal for small loads and saves water and electricity. It is controlled by the HALF LOAD (8) but
ページ8に含まれる内容の要旨
User instructions EXTRA PROGRAMS Button (6) gives access to three extra programs in addition to the ones which can be selected directly using the program selector button. after This button must be pressed (the light comes on) selection of the "main" program (2,3,4) and has no effect if it is pressed when programs 1 and 5 are selected. This function is retained in the memory, so the button has to be pressed again (the light goes out) if the user wishes to execute one of the 5 main programs at th
ページ9に含まれる内容の要旨
User instructions ADJUSTING THE WATER SOFTENING SYSTEM Depending on model, the setting may be made electronically or by means of a selector switch. ELECTRONIC SETTING (models with display) N.B.: for the setting below to be possible, a washing program other than the soak program must be set. Press the PROGRAM DELAY button (10) and keep it pressed until the preset value appears followed by a full stop (normally 3.). Release the button then press it again in succession to display the value require
ページ10に含まれる内容の要旨
User instructions SWITCH SETTING (models without display) According to the machine model, the selector which acts on the adjustment may be located: • inside the plastic locking ring located on the right-hand side, inside the dishwasher; • inside the water softener, just below the cap. Both allow for adjustment to 5 settings: WATER HARDNESS TABLE WATER HARDNESS SETTING German Degrees (°dH) French Degrees (°dF) 0 - 4 0 - 7 Setting N. 1 NO SALT 5 - 9 8 - 15 Setting N. 1 10 - 17 16 - 30 Setting N. 2
ページ11に含まれる内容の要旨
User instructions If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. You must wait about 1 minute before closing the door to restart the program. When the door is closed the program will continue from where it was interrupted. This operation should only be carried out if strictly necessary, because it might cause problems in execution of the program. END
ページ12に含まれる内容の要旨
User instructions 2. Troubleshooting The dishwasher is capable of signalling a number of faults through the simultaneous illumination of several indicator lights, with the following meanings: FAULT DESCRIPTION Acquastop failure The anti-flooding system has been activated (for the E1 relevant models only). The system is tripped in case of water leaks. Contact the after-sales service. Safety level The system which limits the water level inside the dishwasher has been tripped. Interrupt the program
ページ13に含まれる内容の要旨
User instructions FAULT DESCRIPTION Turbine flow-regulator malfunction (for the relevant models only) The appliance is not able to "measure" the amount of water loaded accurately. Interrupt the program and E7 switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. Alternate washing system malfunction Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program
ページ14に含まれる内容の要旨
INSTRUCTION MANUAL WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS AND FOR CLEANING DISHWASHERS AND FOR CLEANING DISHWASHERS
ページ15に含まれる内容の要旨
Contents 1. Safety and operating instructions __________________________26 2. Installation and hook-up _________________________________29 3. Operating instructions ___________________________________31 4. Cleaning and maintenance _______________________________43 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are lai
ページ16に含まれる内容の要旨
Safety instructions 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE EEC DIRECTIVES 72/23, 89/336 (INCLUDING 92/31) CURRENTLY IN FORCE, INC
ページ17に含まれる内容の要旨
Safety instructions IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED. ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY. OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THE APPLIANCE MUST THEN BE TAKEN TO A SORTED WASTE COLLECTION CENTRE.
ページ18に含まれる内容の要旨
Safety instructions DO NOT UNDER ANY CIRCUMSTANCES TOUCH THE HEATING ELEMENT IMMEDIATELY AFTER THE END OF A WASHING PROGRAM. OVER TIME, THE DISHWASHER HEATING ELEMENTS MAY CHANGE COLOUR, IN PART OR OVERALL. THIS IS PERFECTLY NORMAL AND DOES NOT IN ANY WAY AFFECT THE OPERATION OF THE APPLIANCE. DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE. KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLAC
ページ19に含まれる内容の要旨
Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw t
ページ20に含まれる内容の要旨
Installation instructions CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter A supplied with the Take care to screw the hose firmly into dishwasher. place with your hands and then complete by tightening about ¼ of a turn with pliers. In dishwashers equipped with the ACQUASTOP device, the filters is already fitted inside the threaded ring. The dishwasher can also be connected to a hot water supply not exceeding 60°C. Supplying t
