ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
ページ2に含まれる内容の要旨
CONTENTS EN Contents 1 INTRODUCTION ........................................................................................3 2 DESCRIPTION AND USE OF THE CONTROLS ..........................................5 2.1 Front panel .................................................................................................5 2.1.1 Display .......................................................................................................6 2.2 Setting the washing program and switching on and of
ページ3に含まれる内容の要旨
EN 2 Rev 0.0
ページ4に含まれる内容の要旨
INTRODUCTION EN 1 INTRODUCTION Thank you for choosing one of our products. T o use this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your ap- pliance’s functions. The texts are easy to understand and are com- plete with detailed illustrations. This user-friendly manual will provide answers to all your questions about use of the dishwasher. Before using this dishwasher, carefully read chapter 2
ページ5に含まれる内容の要旨
INTRODUCTION EN Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab. 1-01 4 Rev 0.0
ページ6に含まれる内容の要旨
USER INSTRUCTIONS EN 2 DESCRIPTION AND USE OF THE CONTROLS 2.1 Front panel All the dishwasher contr ols are grouped on the front panel (see fi g. 2-01). A brief description (see tab. 2-01) of the various elements on the front panel is given below. Fig. 2-01 1 On/Off button 2 Program selection buttons (P1…P5) 3 Half-load wash button (depending on the model) 4 Program delay button (depending on the model) 5 Start/Pause button 6 Power on indicator light 7 Program indicator lights 8 Disp
ページ7に含まれる内容の要旨
USER INSTRUCTIONS EN 2.1.1 Display The dishwasher is fi tter with a practical display (see fi g. 2-02) which provides information on the programmed dishwasher functions. Fig. 2-02 A brief description of the various indicator lights on the display is shown below (see tab. 2-02). Delay function set. Sanitation function selected. Half-load function selected (lights up together with or ). Half-load function on upper rack selected. Half-load function on lower rack selected. Add rinse-
ページ8に含まれる内容の要旨
USER INSTRUCTIONS EN 2.2 Setting the washing program and switching on and off The dishwasher is equipped with a control panel and an information display (ref. 8 fi g. 2-03) which are used to program the appliance and switch it on and off. Fig. 2-03 Rev 0.0 7
ページ9に含まれる内容の要旨
USER INSTRUCTIONS EN To select the most suitable program for the dishes to wash, consult the fol- lowing tables which specify the most appropriate type of washing sequence depending on the kind of dishes and how dirty they are (see tabs. 2-03a and 2-03b). TIME CONSUMPTION PROGRAM, NUMBER CONDITION OF PROGRAM WATER ENERGY AND SYMBOL DISHES SEQUENCE MINUTES (1) kWh (2) Pans and dishes 3.9 l 1 RINSE waiting to be Cold pre-wash. (*) 0.03 1.03 gal. washed Wash at 38°C (100.4°F). 10,6 l 2 SHOR
ページ10に含まれる内容の要旨
USER INSTRUCTIONS EN TIME CONSUMPTION PROGRAM NUMBER AND DISHES AND PROGRAM WATER ENERGY MINUTES SYMBOL CUTLERY SEQUENCE (1) kWh (2) Cold pre-wash. Wash at 45°C (113°F). 10.8 l Moderately 6 CRYSTAL Cold rinse. (*) 2.85 1.15 dirty Rinse at 69°C gal. (156.2°F). Dry. Cold pre-wash. Wash at 55°C (131.00°F). 14.8 l Moderately 7 NORMAL Cold rinse. (*) 3.91 0.8 dirty Rinse at 68°C gal. (154.4°F). Dry. Cold pre-wash AUTO (Depending of SUPER Moderately 11-15 l the type of dirty) WASH dirty, i
ページ11に含まれる内容の要旨
USER INSTRUCTIONS EN Only run the soak program with half loads. To run programs 6, 7, 8, 9 (see tab. 2-03b), select the required standard pro- gram (see programs 2, 3, 4, 5 in tab. 2-03a) and then press the “soak” button (program 1 in tab. 2-03a). The half-load option (ref. 3 fi g. 2-03) is available for all programs, except the soak program. After using the above tables to choose the most suitable washing cycle, pr o- gram the appliance. Before starting a washing program, make sure that
ページ12に含まれる内容の要旨
USER INSTRUCTIONS EN 2.2.2 Selecting a program In this dishwasher model all programming operations can only be performed with the door closed. With the door open, the symbols “--” appear on the display (ref. 8 fi g. 2-03) and the program indicator lights (ref. 7 fi g. 2-03) remain off. Select the programs using the relative buttons (see P1, P2, P3, P4, P5 fi g. 2- 04). Press the button relative to the required program (see tab. 2-03a, 2-03b). The relative indicator light shines to confi rm th
ページ13に含まれる内容の要旨
USER INSTRUCTIONS EN 2.2.4 End of program The end of the program is signaled by a short beep and the message “End” appears on the display (ref. 8 fi g. 2-03). Press any of the program buttons to cancel “End” from the display and prepare the dishwasher for a new cycle; this can also be done by opening and closing the door or switching the appliance off and back on again. 2.2.5 Interrupting a program T o interrupt the current program: • press the start/pause button (ref. 5 fi g. 2-03) for
ページ14に含まれる内容の要旨
USER INSTRUCTIONS EN 2.2.7 Canceling the current program To cancel the current program, fi rst interrupt it (see para 2.2.5 “Interrupting a program”). Then press buttons P1+P2 (see fi g. 2-05) together until the fi rst three program indicator lights turn on. The display indicates “P0” and the dishwasher automatically goes to the end of the cycle, draining the water from the tray (dur- ing this phase, “Time to end” fl ashes on the display). When draining has been completed, the end of cycle
ページ15に含まれる内容の要旨
USER INSTRUCTIONS EN 2.2.8 Options (available for all programs except soak and when the display shows “END”) HALF-LOAD (only on some models) This option is particularly suitable for reduced loads and saves on water and electricity. Press the ½-load button (ref. 3 fi g. 2-03) and then select washing in just one rack (upper or lower). After selecting the required program (see para 2.2.2 “Selecting a program”), proceed as follows: • pr ess the ½-load button (ref. 3 fi g. 2-03) once to
ページ16に含まれる内容の要旨
USER INSTRUCTIONS EN Display Visualizzazione su display Fig. 2-07 HALF OF THE CUTLERY BASKET CAN BE PLACED IN THE RACK SELECTED FOR ½ LOAD WASHING. ATTENTION: THERE IS NO POINT IN LOADING DISHES AND CUTLERY IN THE UNSELECTED RACK AS THE WATER WILL ONLY REACH THE SELECTED RACK. PROGRAM DELA Y Press the Program delay button (ref. 4 fi g. 2-03) to select a pre-washing program delay of up to 12 hours from when programming takes place. This makes it possible to use the dishwasher
ページ17に含まれる内容の要旨
USER INSTRUCTIONS EN To cancel the “program delay” once it has begun: • pr ess the start/pause button (ref. 5 fi g. 2-03) for a few seconds until the clock symbol shines steady on the display; • press the program delay button (ref. 4 fi g. 2-03) several times until the pro- gram delay has been cancelled (the clock symbol disappears); • press down on the start/pause button (ref. 5 fi g. 2-03) until the new pro- gram starts. N.B.: it is not possible to select the “program delay” function if the
ページ18に含まれる内容の要旨
USER INSTRUCTIONS EN 2.3 Additional functions (Customizing user parameters; available for all programs, except soak) 2.3.1 Adjusting the water softener N.B.: A DIFFERENT WASHING PROGRAM FROM SOAK MUST BE USED TO MAKE THE FOLLOWING ADJUSTMENT. The electr onic control system incorporates an indirectly accessible program- ming procedure for adjusting the level of water hardness. To access the pro- gramming mode, switch on the dishwasher and close the door. Then: • pr ess the Pro
ページ19に含まれる内容の要旨
USER INSTRUCTIONS EN Water hardness table (see tab. 2-04) WATER HARDNESS SETTING American degrees German degrees (°D) French degrees (°F) grains/gallon 0 - 4 0 - 7 0 - 4.5 H0 5 - 15 8 - 25 4.6 - 14.5 H1 16 - 23 26 - 40 14.6 - 23.5 H2 24 - 31 41 - 60 23.6 - 35 H3 32 - 47 61 - 80 35.1 - 46.5 H4 48 - 58 81 - 100 46.6 - 58.5 H5 Tab. 2-04 Contact your local water board for information on the hardness of your water supply. 18 Rev 0.0
ページ20に含まれる内容の要旨
USER INSTRUCTIONS EN 3 ENERGY SAVING AND ENVIRONMENTAL RESPECT • Always try to run the dishwasher fully loaded. • Do not wash the dishes under a running tap. • Use the most suitable washing program for each type of load. • Do not pre-rinse. • If available, connect the dishwasher to a hot water system with a tempera- ture of up to 60°C (140°F). • When possible, skip the drying cycle by opening the door after washing: the air and the residue heat will dry the dishes to perfection. 3.1
