ページ1に含まれる内容の要旨
Installation instructions
Integrated dishwasher
To prevent accidents
and machine damage,
read these instructions
before
installation or use, M-Nr, 05 620 662
ページ2に含まれる内容の要旨
Contents iMPORTANT SAFETY INSTRUCTmONS ................................. 3 mNSTRUCTmONSmMPORTANTES SUR LA SECURmTE ..................... 5 Caring for the environment .......................................... 7 Disposal of the packing material ....................................... 7 Disposal of an old machine ........................................... 7 Opening the door .................................................. 8 Opening the door without a panel in place .............................
ページ3に含まれる内容の要旨
iMPORTANT SAFETY iNSTRUCTiONS mnstallation If there is any doubt concerning installation contact the Technical Insta!lation, maintenance and Service Department. repair work shou,d be by aM,e,e USA 1-800-999- !360 authorized service technician. Work by techserv@mieleusa.com unqualified persons could be a hazard and may void the warranty. CDN 1-800-565-6435 service@miele.ca Th,s equipment isnot designed for maritime use or for use in mobile installations such as caravans or aircrafL However, under
ページ4に含まれる内容の要旨
iMPORTANT SAFETY iNSTRUCTiONS E_ectrica_ safety ChHd safety Before installation, make sure the Ensure that any plastic wrappings, voltage and frequency listed on the bags etc. are disposed of safely data plate correspond with the and kept out of the reach of babies and household electrical supply. This data young children. Danger of suffocation! must correspond to prevent injury and machine damage. Consult a qualified ,fthe app,iance isremoved from its installation and will not be used, electric
ページ5に含まれる内容の要旨
iNSTRUCTiONS JMPORTANTES SUR LA SECURJTE Installation Si vous avez des doutes au sujet de I'installation, contactez le D6- du service Miele, technique partement L'insta,ation etles travaux de r6pa- ration etd'entretien doivent Ure ef- fectu6s par un technicien de service USA !-800-999-1360 autoris6 Miele, Les travaux effectues techserv@mieleusa,com par des personnes non qualifi6es, CDN !-800-565-6435 pourraient _tre dangereux et faire annu- service@miele,ca ler la garantie, _]HHHHHHHH _;Jii]ii C
ページ6に含まれる内容の要旨
iNSTRUCTiONS JMPORTANTES SUR LA SECUFHTE Securite des enfants S6curite 61ectrique Avant I'installation, s'assurer que la S'assurer de disposer de bus les tension et fr6quence 6num6r6es emba,ages de p ast que, sacs etc sur la plaque signal6tique correspon- et de les garder hors de la port6 des dent b,la source d'61ectricit6 de la resi- b6bes et jeunes enfants. Danger de dence. Ces donnees doivent corres- suffocatio!! pondre afin d'6viter de vous blesser et d'endommager I'appareik Consulter un Si
ページ7に含まれる内容の要旨
Caring for the environment Disposa_ of the packing Disposa_ of an o_d machine materia_ Old appliances may contain materials that can be recycled. Please contact The cardboard box and packaging your local recycling authority about the protect the appliance during shipping. possibilty of recycling these materials. These materials are biodegradable and recyclable. Please recycle. Ensure that the appliance presents no danger to children while being stored Ensure that any plastic wrappings, for dispo
ページ8に含まれる内容の要旨
Opening the door Opening the door without a Without the mounting bracket in place: pane[ in place [] Gently pull on the upper portion of [] Grip the T shaped opening with a the mounting bracket until the door finger and pull the door open, latch releases (small arrow),
ページ9に含まれる内容の要旨
Product and Cut-out Dimensions G 600 Series Dishwashers Removing the Jeg extensions The black leg extensions can be Full size models G 643 - G 663 removed to reduce the machine height to 32 1/4"- 33" (819-838 ram) (see Inset). A = Black leg extension (removable) B = White leg (must be installed on machine). [] After removing the black leg extensions, screw the white legs onto the dishwasher. Contact the Miele Technical Service i re necessary. Department for the appropriate legs. .........
ページ10に含まれる内容の要旨
Product and Cut-out Dimensions G 800 Series Dishwashers Full size models G 843 - G 863 greater than 35" (889 ram), extended ill legs (part# 02 702 601) are necessary. Contact the Miele Technical Service lO
ページ11に含まれる内容の要旨
Installation 1. mnstall the steam deflector i_1IiIIiIIIIIIIIIIIIIIIIIIIIIIIIIIII_j_Hiji_f_IIIIII__[_i_i_i_i_i!!! i If the counter is made of different A stainless steel steam deflector is materials, the steam deflector i_i supplied to protect the countertop from should be positioned so it covers the _: steam and condesation when the edge where the materials are ioined, ! dishwasher is opened, If the countertop Countertops with wood or laminate is made of Corian®, granite, marble or ii edging sho
ページ12に含まれる内容の要旨
installation [] Center the steam deflector in the [] Press the optic indicator reflector in opening for the dishwasher and align place, with the lower front edge of the cou ntertop, Note: For rounded countertops it may be necessary to pull the steam deflector closer to the counter's edge so the optic reflector will be visible, [] Secure the deflector in place using the supplied nails, [] Wipe of any excess silicone with a solution of liquid dish soap and warm water, 12
ページ13に含まれる内容の要旨
installation Stone or marble countertops: The steam deflector is not required for countertops made of solid, waterproof material. But it is needed for determining the correct position of the optic indicator reflector. [] Remove the black plastic reflector holder and the tape holding it in place from the steam deflector. [] Line up the D_acK reflector no_oer w_m the tracing ana Dress nrc olace [] With the reflector cut out left and ffontward, align the steam deflector with the front edge of the c
ページ14に含まれる内容の要旨
installation 3. mnstaJJthe shale skis 2. Install the mounting brackets Two slide skis are included and should be installed on the feet of the To ensure stability this dishwasher dishwasher before the machine is should be securely attached to the pushed under the countertop, This will countertop with the two mounting allow the machine to slide easier, brackets included, protect the floor, and allow adiustment of the rear leveling legs from the front of the unit, [] First, adjust the height of the
ページ15に含まれる内容の要旨
installation 4, Install the dishwasher under [] Make certain that there are no rough edges that could damage the power the countertop cord or hoses. If metal cabinets are The dishwasher must be installed so used, place the supplied rubber that the water and electricity supplies grommet around the edge of the can be accessed through an adiacent opening before passing the cable cabinet. The supplies must not be through. located behind the machine. z_WARNING - Fire hazard Do not cover or crush the
ページ16に含まれる内容の要旨
installation 5. Leve_ the _egs [] The rear leveling legs can be [] Adiust the front leveling legs by adiusted with a T20 Torx screwdriver pushing on the feet with a slotted screwdriver, by turning the screws at the front of the slide skis, [] Tipping the machine slightly backwards, if posssible will make To raise the machine turn clockwise, adjusting the front legs easier, Make To lower the machine turn counter sure the machine is level when clockwise, adjustments are complete, Several turns may
ページ17に含まれる内容の要旨
installation 6. mnstaH the custom door PaneJ Dimensions: pane_ 1/,, (60 ore) Width: ............... 23 ,2 A custom door panel must be installed Range of panel heiqht: on the dishwasher before it can be G 800 series .......... 27 1/2"- 30 1/4" safely operated. A single large panel or ................... (699 - 768 ram) a two piece panel separated at the drawer line can be used. G 600 series .......... 25 1/2"- 28 1/4" ................... (648- 718 ram) Panel size is determined in the following ma
ページ18に含まれる内容の要旨
installation The door panel is attached to the dishwasher using the mounting bracket that comes secured to the front of the unit, To remove the bracket: [] Open the door 2- 4" (5 - 10 cm), [] Loosen the bracket retaining screw (black arrow) located on each side of the machine door, [] Pull the bracket up until the upper section of the bracket disengages from the Iocator pins, then remove the bracket, 18
ページ19に含まれる内容の要旨
Installation Install the bracket on the rea_ of the [] Using a pencil, lightly draw a vertical custom doo_ panel centerline on the panel (See illustration on the next page), [] Make sure the dishwasher is leve!, [] Draw a horizontal line X inches up [] Measure the distance X between the from the bottom edge of the panel, round hole in the machine outer door panel (shown in inset) and the lower For two piece panels: edge of the adioining cabinet door. Two piece panels should be made so that any i
ページ20に含まれる内容の要旨
Installation [] Double check the location of the [] Place the bracket on the door panel so the notches, _, cross the bracket before mounting the panel to the dishwasher. previously drawn centerline, and the bottom of the bracket lines up with The door handle must be installed on the horizontal X line. the panel before it is attached to the machine. It should be located in the [] Mark and drill pilot holes for the 3 Ii center of the panel at a height that will screws using a /32 (2,5 ram) drill b
