ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
UNDERCOUNTER DISHWASHER
INSTRUCTIONS D'INSTALLATION
LAVE-VAISSELLE SOUS PLAN DE TRAVAIL
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
W10275503B
ページ2に含まれる内容の要旨
Table of Contents Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Instructions (cont.) Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Install the Door Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Tools and Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Custom Panel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 14 Location Requirements . . . . . . . .
ページ3に含まれる内容の要旨
INSTALLATION REQUIREMENTS Other parts you may also need: Tools and Parts Gather the recommended tools and parts before starting Masking or Moisture installation. Read and follow the instructions provided with (3.81–5.0 cm) duct tape barrier tape any tools listed here. (Part Number Screw-type 4396277). clamps (3 maximum) All Installations Tools needed: NOTE: Moisture barrier tape is recommended when installing a dishwasher under a wood countertop. Flat-blade NOTE: Parts available for purchase in
ページ4に含まれる内容の要旨
Location Requirements Grounded electrical supply required. Check location where dishwasher will be installed. The location must provide: Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. • easy access to water, electricity and drain. The location where the dishwasher will be installed must • convenient access for loading and unloading dishes. provide clearance between motor and flooring. Motor Corner locations require a 2"
ページ5に含まれる内容の要旨
(60.6 cm) 24" (61 cm)** (86 cm) min . with wheels removed (17.2 cm) (26.7 cm) Clear (4.4 cm) Area (15.9 cm) (6.4 cm) Product and Cabinet Opening Dimensions *Insulation may be compressed. (not used on all models) Check that all surfaces have no protrusions that would prohibit dishwasher installation. NOTE: Shaded areas of cabinet walls show where utility connections may be installed. *Measured from the lowest point on the underside of countertop. May be reduced to 33⁷⁄₈" (86 cm) by removing w
ページ6に含まれる内容の要旨
Drain Requirements Electrical Requirements • A new drain hose is supplied with your dishwasher. Be sure that the electrical connection and wire size are If drain hose is not long enough, use a new drain hose adequate and in conformance with the National Electrical with a maximum length of 12' (3.7 m) (Part Number Code, ANSI/NFPA 70 - latest edition and all local codes and 3385556) that meets all current AHAM/IAPMO test ordinances. standards, is resistant to heat and detergent, and fits the A cop
ページ7に含まれる内容の要旨
6” (15.2 cm) INSTALLATION INSTRUCTIONS Prepare Cabinet Opening—Existing Utilities Check water and electrical 1 placement Water line Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. Cable Disconnect power 1 If the water line and the cable extend to the locations Disconnect electrical power at the fuse box or circuit shown, proceed to the “Install Drain Hose” section.
ページ8に含まれる内容の要旨
6” (15.2 cm) Power Supply Cord–Prepare hole Direct Wire–Route cable 2 3 Metal Wood cabinet cabinet Route cable from power supply through cabinet hole (cable Wood cabinet: Sand the hole until smooth. must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit Metal cabinet: Cover hole with grommet included with cable from moving when dishwasher is moved into power supply cord kit. cabinet opening. Option B, Direct Wire: Prepare and Route W
ページ9に含まれる内容の要旨
Route water supply line Slide nut and ferrule 3 5 onto tubing Nut Ferrule Slowly route water supply line through hole in cabinet. Copper tubing only: Slide nut, then ferrule, about 1" (If using copper tubing, it will bend and kink easily, so be (2.5 cm) onto copper tubing. gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left NOTE: To avoid vibration during operation, route the side of the dishwasher. water supply line so that it doe
ページ10に含まれる内容の要旨
Option A, Waste disposer – no air gap Install Drain Hose IMPORTANT: Always use a new drain hose. Check local Waste disposer – no air gap codes to determine whether an air gap is required. Large silver Disposer inlet Disposer inlet drain hose clamp Drill hole 1 Drain hose D Drain trap rain trap 1. Using a hammer and screwdriver, 1¹⁄₂" 1 (3.8 cm) knock plug into disposer. 2. Use needle-nose pliers to remove 2 plug. If needed, drill a 1¹⁄₂" (3.8 cm) diameter hole in cabinet wall or side of the ope
ページ11に含まれる内容の要旨
Option C, Waste disposer – with air gap Install Moisture Barrier (under a wood countertop) Waste disposer – with air gap Air gap Air gap Install moisture barrier S Screw-type clamps Screw-type clamps crew-type clamps (under a wood countertop) L Large silver drain arge silver drain h hose clamp ose clamp Disposer inlet Disposer inlet (provided) Rubber hose connector Drain hose Moisture barrier Drain trap 1. Using a hammer and screwdriver, 1 knock plug into disposer. 2. Use needle-nose plie
ページ12に含まれる内容の要旨
Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not What type of electrical use door panel as a worktable without first covering with a connection will you use? towel to avoid scratching the door panel. Using two or more people, grasp sides of dishwasher door Power Supply Cord: frame and place dishwasher on its back. Follow Option A instructions Direct Wire: Remove panels 2 Follow Option B instructions NOTE: If using Option B
ページ13に含まれる内容の要旨
Power Cord−Secure cord WARNING 4 on strain relief Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Power Supply Cord— 2 Tighten strain relief screws to secure cord. Connect ground wire Power Cord—Reinstall 5 terminal box cover Ground Ground wire wire Washer Ground connector Remove the green grounding screw and
ページ14に含まれる内容の要旨
2" (5 cm) Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed Install the Door Handle (you will need to measure the lowest point on the underside of the countertop and the highest point on the (on some models) floor). Refer to “Dishwasher Height Adjustment Chart” for wheel position and the number of turns needed. Install door handle Dishwasher Height Adjustment Chart Mounting stud Cabinet Wheel Number of turns opening height position on fro
ページ15に含まれる内容の要旨
Custom panel dimensions - Dishwashers Custom panel installation - 1 with control panel on the front Dishwashers with control panel on the top (65.8 cm) 23¹⁄₂" *30³⁄₁₆" (76.7 cm) (59.7 cm) (19.1 mm) ³⁄₄" (19.1 mm) (3.2 mm) * This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height * This dimension is for 4" (10.2 cm) toe kick. If the of the wood panel accordingly. Not recommended for installation needs a higher toe kick, adjust the height t
ページ16に含まれる内容の要旨
Mark line Attach body panel 3 6 " (25.2 cm) Back Align top edges Reinstall 3 screws Top edge each side Customer-supplied panel Measure 9²⁹⁄₃₂" (25.2 cm) from top edge and mark a line on the back of customer-supplied custom panel. Position the Attach the panel assembly to the door by reinstalling the outer panel on the back of the customer-supplied custom three screws on each side; do not tighten completely. This panel as shown, so that the top holes in the outer panel are reinstallation of the
ページ17に含まれる内容の要旨
Install Custom Panel – Option 2 Mark pilot holes 3 (Models KUDC03IV and KUDS30IV) All models require an accessory option to attach custom Mark pilot panels. Kit Number 8171555 (black), 8171556 (white) or holes 8171557 (biscuit) are available. To order, call customer service at 1-800-444-1230. NOTE: A custom full-front panel must weigh no more than 14 lbs (6.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions
ページ18に含まれる内容の要旨
Option 1, Countertop attachment: Insert plastic buttons 2 Remove bracket 1 plastic Tabs must point button to the right Push the plastic buttons out of the side of the tub. Remove the brackets from the package and place in the NOTE: Save the buttons to cover the holes after open slots on the left and right-hand top of the dishwasher is installed. dishwasher collar as shown. Reinstall bracket 3 Insert bracket 2 bend tabs Insert the bracket into the slot on the collar. Using a pair Push bracket in
ページ19に含まれる内容の要旨
Move dishwasher close to Open and close door 2 4 cabinet opening Water line Direct wire only Drain hose Cable With another person holding the dishwasher to keep it from tipping, open and close the door a few times. If the door closes or falls open under its own weight, the door tension will need to be adjusted. IMPORTANT: Double-check correct placement of utilities. Grasp the sides of the dishwasher at the edges of the door panel. Tilt dishwasher backward on wheels and Closes too quickly— 5 move
ページ20に含まれる内容の要旨
Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs. With Move dishwasher into 7 some installations, it may be easier to adjust the front leg cabinet opening using the ³⁄₁₆" hex head socket or adjustable wrench. Insulation Preferred method Optional method blanket IMPORTANT: If wheels were removed, cover the floor when moving the dishwasher. Slowly move dishwasher completely into cabinet opening. Do not kink or pinch Check level side to side and 10
