ページ1に含まれる内容の要旨
KAD-9
TECHNICAL EDUCATION
DRAWER
DISHWASHER
JOB AID 4317364
ページ2に含まれる内容の要旨
FORWARD This KitchenAid Job Aid, “Drawer Dishwasher,” (Part No. 4317364), provides the technician with information on the installation, operation, and service of the Drawer Dishwasher. It is to be used as a training Job Aid and Service Manual. For specific information on the model being serviced, refer to the “Use and Care Guide,” or “Tech Sheet” provided with the dishwasher. The Wiring Diagram used in this Job Aid is typical and should be used for training purposes only. Always use the Wiring D
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Page GENERAL............................................................................................................................... 1-1 Safety First......................................................................................................................... 1-1 Model & Serial Number Designations ................................................................................ 1-2 Model & Serial Number Label And Tech Sheet Locations............................
ページ4に含まれる内容の要旨
Page DIAGNOSTICS & TROUBLESHOOTING .............................................................................. 6-1 Diagnostics ........................................................................................................................ 6-1 The Error Code Display Mode ....................................................................................... 6-1 Error Codes .........................................................................................................
ページ5に含まれる内容の要旨
GENERAL SAFETY FIRST Your safety and the safety of others is very important. We have provided many important safety messages in this Job Aid and on the appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you don’t DANGER immediately fo
ページ6に含まれる内容の要旨
MODEL & SERIAL NUMBER DESIGNATIONS MODEL NUMBER MODEL NUMBER K U D D 01 D P PA 0 PRODUCT GROUP K = KITCHENAID BRAND PRODUCT IDENTIFICATION UD = UNDERCOUNTER DISHWASHER FEATURE LEVEL P = DERIVATIVE S = SUPERIOR D = DRAWER SERIES 01 = 01 SERIES 01 SERIES—CONSOLE DESIGN T = 6″ TRADITIONAL CONSOLE D = SPLIT CONTROL CONSOLE F = FULLY INTEGRATED I = 4″ INTEGRATED CONSOLE V = VBL PRO LINE SERIES YEAR OF INTRODUCTION P = 2004 COLOR CODE AL = ALMOND ON ALMOND BL
ページ7に含まれる内容の要旨
MODEL & SERIAL NUMBER LABEL AND TECH SHEET LOCATIONS The Model/Serial Number Label and Tech Sheet locations are shown below. Model/Serial Number Label Location (On Frame Between Doors) Tech Sheet Location (On Inside Rear Of Cabinet) 1-3
ページ8に含まれる内容の要旨
SPECIFICATIONS Electrical: Electrical Supply................................................................................ 110 - 120 VAC, 60 Hz Dual Dishwasher Motor Load .................................................................................................... 3.1 amperes Total Load ..................................................................................................... 9.2 amperes General: Wash / Drain Pump Motor ................................................
ページ9に含まれる内容の要旨
KITCHENAID DISHWASHER WARRANTY TWO-YEAR FULL WARRANTY For two years from the date of purchase, when this dishwasher is operated and maintained according to instructions attached to or furnished with the product, KitchenAid will pay for replacement parts and repair labor costs to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company. THIRD THROUGH FIFTH YEAR LIMITED WARRANTY ON NYLON COATED DISHRACKS, NYLON CUPSHELVES, SILVERWARE BASKETS
ページ10に含まれる内容の要旨
— NOTES — 1-6
ページ11に含まれる内容の要旨
INSTALLATION INFORMATION GENERAL IMPORTANT: Observe all governing codes • pencil and ordinances. Failure to meet codes and • sandpaper ordinances could lead to fire or electrical shock. • level • wood cutting board Proper installation is your responsibility: • adjustable wrench that opens to 1-1/8″ • Contact a qualified installer to insure that the (29 mm) dishwasher is installed to meet all electrical • 7 mm socket wrench and plumbing national and local codes and • 5 mm socket wrench ordinances
ページ12に含まれる内容の要旨
PRODUCT DIMENSIONS 23-7/16" 22-7/16" * (57 cm) (59.5 cm) raised tabs for optional top attaching brackets 32-3/16" - 34-1/2" 30" *** (81.8 cm - 87.8 cm) (76.2 cm) * If custom wood panels are to be used, the product depth is specified with an 11/16" (18 mm) door panel thickness. ** Toe kick depth: Factory supplied – 2 - 4-3/8" (5-11 cm); side Custom wood – 5" (12.7 cm) less the attaching toe kick panel thickness for integrated. tabs Minimum panel thickness using the supplied screws is 3/8
ページ13に含まれる内容の要旨
CABINET DIMENSIONS / REQUIREMENTS moisture typical installation protection tape counter top 4" moisture (10 cm) protection tape tape 1/2" (12.7 mm) from front of counter top 32-5/16" - 34-5/8" It is recommended that wood cabinetry surrounding (82.0 cm - 88.0 cm) the dishwasher be sealed with an oil based paint or moisture-proof polyurethane to prevent possible damage from heat and humidity. The utility hole must be located as shown. If the hole is not located as shown, the hoses will preven
ページ14に含まれる内容の要旨
Power cord must plug into a mating 3 prong, ELECTRICAL REQUIREMENTS grounded outlet located in the cabinet next to the dishwasher opening. Outlet must meet all WARNING local codes and ordinances. The 3 prong grounded outlet must be installed within 6″ (15.2 cm) to 18″ (45.7 cm) of the cabinet side wall. NOTE: The power outlet must be accessible after installation. Electrical Shock Hazard GROUNDING INSTRUCTIONS Plug into a grounded 3 prong outlet. For a grounded, cord-connected dishwasher: Do not
ページ15に含まれる内容の要旨
INSTALLING THE DISHWASHER Slide the brackets under the raised tabs. WARNING Using the flat side of the side cutting pliers, lightly tap the brackets into place. Make Excessive Weight Hazard sure the locking tabs on the brackets have Use two or more people to move and passed completely through the raised tabs install dishwasher. on the dishwasher. Failure to do so can result in back or mounting other injury. bracket locking tab raised tab 1. Check that the cabinet opening measure- ments, electric
ページ16に含まれる内容の要旨
1. Route the hoses and power supply cord 2. If the cabinet opening is 24″ wide x 34-12″ through the utility hole. IMPORTANT: Push high (61.0 cm x 87.6 cm) flexible extru- against the outside edges of drawers as sions can be attached along the top and shown. Do not push against the middle of sides of the dishwasher. The top and side the drawers. extrusions are different lengths. - Open the drawers to expose the chas- sis trim. WARNING - Center the extrusions. Excessive Weight Hazard - If using th
ページ17に含まれる内容の要旨
Lift the right edge of the drawer off its DIRECT WIRING runner. Slide the runner back into the dishwasher. Lift the drawer completely off WARNING the left-hand runner. Rotate drawer to the right onto its side and place on the protective cover. Slide the left-hand runner back into the dishwasher. Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. 1. Disconnect power. Ope
ページ18に含まれる内容の要旨
3. Remove factory-installed power cord. 5. Run the house wiring through the cable clamp and into the dishwasher. Disconnect the black and white wires of the electrical cord from the EMI filter. 6. Install a cable clamp (not supplied) in the knockout opening. Use a 7 mm socket wrench to remove the ground screw. Remove the green ground 7. From the house wiring, strip 1/2″ (13 mm) wire. of insulation off of each wire. Use a phillips screwdriver to remove the 8. Attach the supply cable to the EMI fi
ページ19に含まれる内容の要旨
If the bottom drawer was rotated, rotate the drawer to unwind the hoses and then WARNING place the drawer on the runners, making Excessive Weight Hazard sure the hoses are looping upward. Use two or more people to move and Close the bottom drawer. install dishwasher. Failure to do so can result in back or other injury. Push the dishwasher partway into the opening. As the dishwasher is being pushed into the opening, carefully pull the inlet hose and drain hose through the utility hole. Allow the
ページ20に含まれる内容の要旨
- Open the drawers to expose the chas- 2. Reach inside the dishwasher to adjust the sis trim. feet using a 5 mm open end, box end, or socket (if space permits) wrench. - Center the extrusions. - If using the optional top attaching brack- Adjust for cabinet height and level. Place ets, place the extrusion under the at- a level on the drawer runners. Level the taching brackets. dishwasher to within 3/32″ (2.4 mm) from front to back. - Remove extrusion backing paper to ex- pose the adhesive. Place
