ページ1に含まれる内容の要旨
CHEMICAL SANITIZING UNDERCOUNTER DISHMACHINES
TECHNICAL MANUAL
INSTALLATION MANUAL FOR EXPORT UNITS
SERVICE MANUAL FOR DOMESTIC UNITS
FOR JACKSON MODELS:
CONSERVER 24LT
CONSERVER 24LTP
An Company
www.jacksonmsc.com
February 20, 2004
P/N 7610-002-10-45 (Revision D)
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Section Description Page I. General Section Specifications 1 Installation Instructions 2 Detergent Control 4 Chemical Dispensing Equipment 5 Operating Instructions 6 Preventative Maintenance 7 Conserver 24LT Cam Timer Operation Instructions 8 Conserver 24LTP Cam Timer Operation Instructions 10 II. Troubleshooting Section 12 III. Dimensions 14 IV. Parts Section Control Panel Assembly 15 Electrical Panel Assembly 16 Ordering Replacement Wire 17 Conduit & Fittings 18 Kickplate Ass
ページ4に含まれる内容の要旨
SPECIFICATIONS ELECTRICAL REQUIREMENTS PERFORMANCE/CAPABILITIES WASH PUMP MOTOR HORSEPOWER 3/4 OPERATING CAPACITY (RACKS/HOUR) RACKS PER HOUR 24 NOTE: Typical Electrical Circuit is based upon (1) 125% of the DISHES PER HOUR 600 full amperage load of the machine and (2) typical fixed-trip circuit breaker sizes as listed in the NEC 2002 Edition. Local GLASSES PER HOUR 600 codes may require more stringent protection than what is displayed here. Always verify with your electrical service contractor
ページ5に含まれる内容の要旨
INSTALLATION INSTRUCTIONS Jackson MSC Inc. provides technical support for all of the dishmachines detailed in this manual. We strongly recommend that you refer to this manual before making a call to our technical support staff. Please have this manual with you when you call so that our staff can refer you, if necessary, to the proper page. Technical support is available from 8:00 a.m. to 5:00 p.m. (EST), Monday through Friday. Technical support is not available on holidays. Contact technical sup
ページ6に含まれる内容の要旨
INSTALLATION INSTRUCTIONS (CONTINUED) ELECTRICAL POWER CONNECTION: Electrical and grounding connections must comply with the applicable portions of the National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes. Disconnect electrical power supply and place a tag at the disconnect switch to indicate that you are working on the circuit. The dishmachine data plate is located on the front of the machine. Refer to the data plate for machine operating requirements, machine vo
ページ7に含まれる内容の要旨
CHEMICAL DISPENSING EQUIPMENT The Conserver 24LT dishmachine is not supplied with integral chemical dispensing feeder pumps. Instead, an independent chemical dispensing system must be connected to the unit prior to use in order to achieve required cleanliness and sanitation. Please consult the literature that accompanied your independent chemical dispensing system for information concerning installation and operation of the dispenser. The Conserver 24LT requires that a separate chemical feeder b
ページ8に含まれる内容の要旨
DETERGENT CONTROL Detergent usage and water hardness are two factors that contribute greatly to how efficiently your dishmachine will operate. Using detergent in the proper amount can become, in time, a source of substantial savings. A qualified water treatment specialist can tell you what is needed for maximum efficiency from your detergent, but you should still know some basics so you’ll understand what they are talking about. First, you must understand that hard water greatly effects the perf
ページ9に含まれる内容の要旨
OPERATION INSTRUCTIONS PREPARATION: Before proceeding with the start-up of the unit, verify the following: 1. The strainer is in place and is clean. 2. That the wash arms are screwed securely into place and that their endcaps are tight. The wash arms should rotate freely. 3. Verify all chemical levels for machine chemical feeder pumps are correct. POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified as being correct. If not, t
ページ10に含まれる内容の要旨
CONSERVER 24LT CAM TIMER OPERATION INSTRUCTIONS The Conserver 24LT cam timer is a 2 minute, 8 cam timer with an OFF-DRAIN function. The following is a description of set points for each cam and function for each switch. CAM 1: Cam 1 is a cut cam with a single notch and serves as the Cycle/Reset. FUNCTION: When the machine is in the operation mode the notch is the home position. The machine will set idle until the door is opened, then cam 1 moves to the start position and holds until the door is
ページ11に含まれる内容の要旨
CONSERVER 24LT CAM TIMER OPERATION INSTRUCTIONS (CONTINUED) SETTINGS: The left side of cam 5 must be set to drop in just past the stop point of the off/drain cam. There must be a dwell between the off/drain and the fill, so that the fill will not run while the machine is in the off state. Any adjustment made to the fill should be made with the right side of cam 5. Proper water level will be achieved when the water touch- es the bottom of the strainer pan. CAM 6: Cam 6 is an adjustable cam and c
ページ12に含まれる内容の要旨
CONSERVER 24LTP CAM TIMER OPERATION INSTRUCTIONS The Conserver 24LTP cam timer is a 2 minute 8 cam timer with an OFF-DRAIN function. The following is a description of set points for each cam and function for each switch. CAM 1: Cam 1 is a cut cam with a single notch and serves as the cycle/reset. FUNCTION: When the machine is in the operation mode the notch is the home position. The machine will set idle until the door is opened, then cam 1 moves to the start position and holds until the door is
ページ13に含まれる内容の要旨
CONSERVER 24LTP CAM TIMER OPERATION INSTRUCTIONS (CONTINUED) CAM 6: Cam 6 is an adjustable cam and controls the sanitizer pump. FUNCTION: The sanitizer pump cam works off the normally closed contacts of cam 6. This requires the switch to be held open by the cam and allowed to drop into the notch to operate the pump. SETTINGS: The left side of cam 6 must be set to drop in just past the starting point of the fill cam. The adjustment for sanitizer volume must be made with the right side of the cam.
ページ14に含まれる内容の要旨
PREVENTATIVE MAINTENANCE The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However, this does not mean that some items will not wear out in time. Jackson highly recommends that any maintenance and repairs not specifically dis- cussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY. Performing maintenance on your dishma- chine may void your warranty if it is still in effect, so if you have a question or concern,
ページ15に含まれる内容の要旨
TROUBLESHOOTING SECTION WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service technician. Many of the tests require that the unit have power to it and live electrical components be exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE. Problem: Nothing on the machine operates; power switch is on and the power light is off. 1. The circuit breaker may be tripped. Reset the circuit breaker. If the breaker trips again, contact an electrician
ページ16に含まれる内容の要旨
TROUBLESHOOTING SECTION (CONTINUED) WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified service technician. Many of the tests require that the unit have power to it and live electrical components be exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE. Problem: Door drops hard and will not stay closed. 1. The door spring is broken. Replace as required. 2. The door hinge is bent. Replace as required. Problem: Water flooding from the machine. 1.
ページ17に含まれる内容の要旨
DIMENSIONS Legend: A - Drain Connection flexible hose; 6’-0” free length, 1” ID x 1 3/8 OD B - Electrical Connection. C - Water Inlet 1/2” Female Pipe Thread,2 1/2” D -Detergent Feeder Connection Note: All dimensions from floor can be increased 1” with adjustable feet supplied. Dimensions: Height (minimum) 33 1/4” Height (maximum) 34 1/4” Width 24 1/4” Depth 22 5/8” Wall Clearance (minimum) 2 1/2” Inside Clearance Height 14 1/2” Inside Clearance Width 20 1/4” Inside Clearance Depth 21 1
ページ18に含まれる内容の要旨
CONTROL PANEL ASSEMBLY 1 4 5 WASH/RINSE OFF/DRAIN MAN.WASH OFF POWER ON AUTO CYCLE POWER CYCLE RINSE/FILL 6 7 8 2 3 * - Item is not shown ITEM QTY DESCRIPTION Mfg. No. 1 1 Control Panel 9330-041-73-89 2 1 Wash Thermometer 6685-111-68-48 3 1 Decal, Control Panel 9905-031-73-92 4 1 Switch, ON/FILL & OFF/DRAIN 5930-011-49-55 5 1 Delime Switch 5930-301-49-00 6 1 Light, Red 5945-111-44-45 7 1 Light, Amber 5945-111-44-44 8 1 Light, Green 5945-111-44-43 9* 4 Nut, Wing, Nylon, 1/4"-20 5310-994-01-00 15
ページ19に含まれる内容の要旨
ELECTRICAL PANEL ASSEMBLY 1 12 3 14, 15 13 2 L1 N 10 6 5 11 - NOT VISIBLE 4 9 7 8 ITEM QTY DESCRIPTION Mfg. No. 1 1 Bushing, Snap 5975-210-03-00 2 1 Decal, Copper Conductors Only 9905-011-47-35 3 1 Decal, Ground-L1-L2 9905-011-47-64 4 1 Timer, 2 Minute, 8 Cam 5945-121-49-56 5 1 Decal, Timer Operation 9905-011-58-06 6 1 Contactor, Motor 5945-109-05-69 7 1 Locknut, 6-32 with Nylon Insert 5310-373-03-00 8 1 Terminal Block 5940-500-09-61 9 1 Terminal Block Spacer 5700-011-40-05 10 1 Electric P
ページ20に含まれる内容の要旨
ORDERING REPLACEMENT WIRE Jackson dishmachines have several color and gauges of wire used in them and it may become necessary to replace these wires. Wire may be ordered from Jackson MSC Inc., but please note that it is only available in feet. Ensure that you order the correct color and gauge. BLACK WIRE: WHITE WIRE: 6 Gauge 6145-002-15-91 10 Gauge 6145-104-19-00 8 Gauge 6145-104-43-00 14 Gauge 6145-104-10-00 10 Gauge 6145-104-16-00 18 Gauge 6145-104-39-00 12 Gauge 6145-112-01-00 18 Gauge with
