ページ1に含まれる内容の要旨
Conveyors
AJ-64 Vision Series
Standard Features
•287 racks per hour hi-temp sanitizing • Completely self-draining, stainless
rinse steel wash and recirculating rinse
pumps.
• 0.77 gallons per rack hi-temp sanitizing
rinse • Exclusive “Energy Guard” controls
system energizes wash, recirculating
• Incoming water pressure regulator
rinse, and final rinse sections only
when a rack is in place.
• Exclusive Adjust-A-Peak feature
(patented) allows the owner operator
• Convenient, externally operated
t
ページ2に含まれる内容の要旨
AJ-64 Vision Series Conveyors POWER RINSE PUMP MOTOR: A 2 HP total- feature eliminates the need for manual controls since you Specifications ly enclosed, fan cooled type motor drives the wash pump have the ability to slow down the conveyor for extended NOTE: The AJ-64 series conveyor dishmachines are and arms. Single-phase motors are capacitor start, wash, power rinse, and final rinse contact time. The unit listed by the National Sanitation Foundation (NSF), induction run with internal thermal o
ページ3に含まれる内容の要旨
FINAL RINSE: Fresh pressurized rinse water enters STEAM: Stainless steel coils are utilized rather than either be plumbed to a drain or pumped back to a boiler the machine through a standard “Y” strainer, solenoid injectors so that contaminated steam being injected into if a condensate return system is available. Must be valve, and approved vacuum breaker assembly and is the wash water is not an issue. Stainless steel tubular installed with a steam pressure regulator (by others) if plumbed to up
ページ4に含まれる内容の要旨
AJ-64 Vision Series Conveyors Specifications Note: Check and/or copy all that apply. Unit shall have the following features: AJ-64 Series Rack Conveyor Dishwasher—Item No. ____________ • Capacity of 288 racks per hour • Fully automatic operation includ- Shall be a Jackson AJ-64 Series, multiple tank rack conveyor dishwasher. utilizing 0.77 gallons of water per ing auto-fill. Sanitization shall be accomplished by using hi-temp (180°F minimum) rack for hi-temp sanitizing rinse. sanitizing rinse. •
ページ5に含まれる内容の要旨
Conveyors AJ-64 Left to Right or Right to Left 25" Operation Shown 1" 21" Opening B Legend to Drawing A– Electrical Connection-See Table for Amperage Requirements (on back) Rear of B–Water Inlet-3/4” I.P.S., 180°F Water Required Machine C– Drain Connection-1 1/2” I.P.S. D–Vent Collar/Splash Shield E–Vent Collar with Damper 4”w. x 16”lg x 7”high-Optional 69 5/8" F– Steam Connection-1” I.P.S. F G– Condensate Return-1” I.P.S. Notes: – All vertical dimensions are +/- 1/2” from floor due to adjustab
ページ6に含まれる内容の要旨
AJ-64 Conveyors Approximate Total Load Amperes Power Supply AJ-64CE AJ-64CS 208/60/1 138.9 18.8 230/60/1 127.5 18.8 208/60/3 81.8 12.3 230/60/3 75.1 12.3 460/60/3 37.6 6.2 Note: Tub Will Accept a Table Flange Recommended Table Fabrication Up to 24 7/8" Rack Rail Table 21" Use Silicone Sealer Between Table and 3/4" Rack Rail Height Lip of Machine to Above Dishtable Prevent Leakage Table Turndown 1/4" – 5/16" Flange 3/4" Max Tub 64" 8" Table to Table 12 1/2" 4 1/2" 25" 8" 10 1/2" 72" 4" 21" Ope
