ページ1に含まれる内容の要旨
GE Consumer & Industrial
Appliances
Installation Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In Dishwashers
ZBD1850*
ZBD1870
* For ZBD1850 also refer to the
instructions provided on the template
packed with that model
ページ2に含まれる内容の要旨
Safety Information BEFORE YOU BEGIN IMPORTANT – The dishwasher MUST S T O P be installed to allow for future removal from the enclosure Read these instructions completely and if service is required. carefully. If you received a damaged dishwasher, you should immediately contact your dealer or builder. IMPORTANT – Observe all governing codes and ordinances. Optional Accessories – See the Owner’s Manual for available • Note to Installer – Be sure to leave these instructions for the custom panel
ページ3に含まれる内容の要旨
Installation Preparation PARTS SUPPLIED: ■ T Tw wo #8 Phillips head w o #8 Phillips head wood scr ood screws, 5/8" long to ews, 5/8" long to secure dishwasher to underside of countertop (in literature package). 2 Wood Screws Wood Screw Wood Screw MATERIALS YOU WILL NEED: ■ Ferr Ferrule, compr ule, compression nut and 90° Elbow (3/8" NPT ession nut and 90° Elbow (3/8" NPT external thread on one end, opposite end sized to fit water supply) ■ Thr Thread seal tape ead seal tape Hand 90° Elbow
ページ4に含まれる内容の要旨
Installation Preparation • The dishwasher must be installed so that drain hose is no PREPARE DISHWASHER ENCLOSURE more than 10’ in length for proper drainage. This Wall Area WARNING must be Free of To reduce the risk of electric shock, fi re, or injury to persons, the Pipes or wires installer must ensure that the dishwasher is completely enclosed 34-1/2" ± 1/2" 24" at the time of installation. Underside of 5" 5" Min. 4" 4" Countertop CLEARANCES: When to Floor installed into a corner, C
ページ5に含まれる内容の要旨
Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use 1-1/2” Dia. an extension cord or adapter plug with this Hole (Max.) appliance. 3” from Cabinet Electrical Requirements 24” • This appliance must be supplied with 120V, 60Hz., and from Wall connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay #282 French Grou
ページ6に含まれる内容の要旨
Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN • The line may enter from either side, rear or fl oor within the Locate and set aside the package containing shaded area shown in Figure F. S T O P 2 Phillips head countertop mounting screws • The line may pass through the same hole as the electrical and 2 additional toekick screws (located in cable and drain hose. Or, cut an additional 1-1/2" dia. hole to the literature package). accommodate the water line. If power cord with p
ページ7に含まれる内容の要旨
Installation Instructions • Lay the dishwasher on its back. Remove the four screws • Remove the side panels and set the dishwasher upright. securing the toekick to the dishwasher, and remove the toekick. To adjust the door springs: • Pull the spring adjustment pin out of the holes, insert in the next highest or lowest hole and test again. Increase Screws Decreas e Toekick Figure I Figure K • Adjust both door springs to the same tension. • Remove the single screw just above and to the side of
ページ8に含まれる内容の要旨
Installation Instructions STEP 2 ADJUST LEVELING LEGS STEP 4 INSTALL POWER CORD • Move the dishwasher close to the installation location and lay Skip this step if dishwasher will be direct wired. it on its back. Use Power Cord Kit WX09X70910, available for purchase from an authorized GE Appliance Dealer. The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances. • Maximum power cord length is 6'. A B Check That White, Black an
ページ9に含まれる内容の要旨
Installation Instructions STEP 6 POSITION WATER LINE AND STEP 8 SLIDE DISHWASHER PARTIALLY HOUSE WIRING INTO CABINET • Position water supply line and house wiring on the fl oor of DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. the opening to avoid interference with base of dishwasher DAMAGE WILL OCCUR. and components under dishwasher. • Slide dishwasher into the opening a few inches at a time. 4" 6" House Water Reposition Dishwasher Wiring by Grasping Both Sides Line With Hands. Do Not Pu
ページ10に含まれる内容の要旨
Installation Instructions STEP 9 POSITION DISHWASHER UNDER ��������������������� ���������������� COUNTERTOP ���������������� • Push the dishwasher into the cabinet. • Push the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up” or interfere with the springs as you slide it into the cabinet. • Center the dishwasher in the opening. ��������� • Front of door panel should be fl ush with face
ページ11に含まれる内容の要旨
Installation Instructions STEP 10 LEVEL DISHWASHER STEP 11 SECURE DISHWASHER TO COUNTERTOP OR CABINET IMPORTANT – Dishwasher must be level for proper In this step you will need Side-Mounting dish rack operation and wash performance. Bracket the 2 Phillips special head • Make sure 1/2" minimum gap is maintained (see Figure T). screws set aside prior to • Place level on door to check that the dishwasher is level side- Step 1. The dishwasher Counter top to-side. Place level on rack track ins
ページ12に含まれる内容の要旨
Installation Instructions STEP 12 CONNECT WATER SUPPLY DRAIN LINE INSTALLATION Connect water supply line to 90° elbow. • Connect drain line to air gap, waste tee or disposer using • Slide compression nut, either previously determined method. then ferrule over end of Compression Nut water line. Ferrule • Insert water line into 90° Method 1 – Air gap with waste tee or disposer elbow. Insert the drain hose to air gap as shown. • Slide ferrule against Hot Water elbow and secure with 90° Elbow
ページ13に含まれる内容の要旨
Installation Instructions STEP 14 CONNECT POWER SUPPLY STEP 15 PRETEST CHECK LIST Skip this step if equipped with power cord. Review this list after installing your dishwasher to avoid Verify that power is turned off at the source. charges for a service call that is not covered by your • Remove junction box cover “A”. warranty. • Locate the three dishwasher wires, (white, black and green) ■ Check to be sur Check to be sure pow e power is OFF er is OFF.. with stripped ends. Insert dishwasher
ページ14に含まれる内容の要旨
2-Piece Toekick Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK ■ T Turn on pow urn on power supply (or plug pow er supply (or plug power cor er cord into outlet d into outlet, , if equipped). ■ S Star tart the unit to check for leaks. t the unit to check for leaks. – Press ON/OFF button to turn unit on – Press CYCLE SELECT button until light below RINSE cycle illuminates ■ Close door Close door.. ■ Check to be sur Check to be sure that w e that water enter
