ページ1に含まれる内容の要旨
Installation
Built-In
Dishwasher
Instructions
l If you have questions, call 800-GECARESor visit our website at: www.GEAppliances.com I
BEFORE YOU BEGIN IMPORTANT- The dishwasher
Read these instructions completely and MUST be installed to allow for future removal from
carefully.
the enclosure if service is required.
Ifvou received a damaged dishwasher, VOUshould
immediatelv contact your dealer or builder.
IMPORTANT- Observe all
governing codes and ordinances.
Optional Accessories- See the Owner's
ページ2に含まれる内容の要旨
Installation Preparation PARTS SUPPLIED: [] Two#8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). [] Two Phillips head, color matched toekick screws 2Wood Screws 2 Color Matched (in literature package). ToekickScrews MATERIALS YOU WILL NEED : [] Ferrule, compression nut and 90° Elbow (3/8"NPTexternal thread on one end, opposite end sizedto fit water supply) Wire Nuts (3) [] Thread seal tape Shut-0ff Thread 90° Elbow, [] UL Listed
ページ3に含まれる内容の要旨
Installation Preparation PREPARE DISHWASHER ENCLOSURE • The dishwasher must be installed so that drain hose is no more than 10feet in length for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure. 34"to 35" Countertop CLEARANCES:When Undersideof installed into a corner, Countertop allow 2" min. clearance to Floor between dishwasher and adjacent cabinet, wall or Dishwashert_Ii_ Square other appliances. Allow and 25-5
ページ4に含まれる内容の要旨
Installation Preparation PREPARE ELECTRICAL WIRING I I \ / i I \ _ ,'T FORPERSONAL SAFETY:Remove house \ I I \ fuse or open circuit breaker before beginning installation. Do not use an 1-1/2" Dia. WARNING extension cord or adapter plug with this Hole(Max.) appliance. Electrical Requirements from • This appliance must be supplied with 120V,60 Hz., and Cabinet connected to an individual properly grounded branch circuit, protected by a 15or 20 ampere circuit breaker or time delay fuse. • Wiring mus
ページ5に含まれる内容の要旨
Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN • The line may enter from either side, rear or floor Locate and set aside the package containing within the shaded area shown in Figure E 2 Phillips head countertop mounting screws • The line may pass through the same hole as the and 2 additional toekick screws (located in electrical cable and drain hose. Or, cut an additional the literature package). 1-1/2" dia. hole to accommodate the water line. If power cord with plug is used,
ページ6に含まれる内容の要旨
Installation Instructions ISTEP 41 INSTALL POWER CORD ISTEP 21ADJUST LEVELING LEGS Skip this step if dishwasher will be direct wired. • Move the dishwasher close to the installation The power cord and connections must comply with location and lay it on its back. the National Electrical Code, Section 422 and/or local codes and ordinances. • Recommended power cord length is 54" min. and 64" max. A B CheckThat White, Black and Remove Green Dishwasher Wires Are Threaded Junction Box Thru Hole in Bac
ページ7に含まれる内容の要旨
Installation Instructions ISTEP 81SLIDE DISHWASHER ISTEP 61 POSITION WATER LINE AND HOUSE WIRING PARTIALLY INTO CABINET DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. • Position water supply line and house wiring on the DAMAGE WILL OCCUR. floor of the opening to avoid interference with base of dishwasher and components under dishwasher. • Slide dishwasher into the opening a few inches at a time, Line Wiring Front Door PanelWith m Knee. Damageto The Figure 0 FigureM Door PanelWill Occur. • As you pr
ページ8に含まれる内容の要旨
Installation Instructions ISTEP 91 POSITION DISHWASHER UNDER COUNTERTOP _ Reposition Dishwasher • Check to be surethatwires are secure under the _'7, _ by Grasping Both dishwasher and not pinched or in contact with door springs or other dishwasher components. With Hands TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs. Check by opening and closing the door, • Push dishwasher into cabinet. The front corners of the dis
ページ9に含まれる内容の要旨
Installation Instructions [STEP 12] CONNECT WATER SUPPLY ISTEP 111SECURE DISHWASHER TO CABINET Connect water supply line to 90° elbow. • Slide compression nut, then ferrule over end of The dishwasher must be secured to the countertop. water line. • Position the dishwasher so that the tub flange aligns • Insert water line into 90° elbow. with the front face of the cabinet frame. • Slide ferrule against elbow and secure with compres- sion nut, IMPORTANT: Check to be sure the dishwasher is centered
ページ10に含まれる内容の要旨
Installation Instructions DRAIN LINE INSTALLATION ISTEP 131 CONNECT DRAIN LINE • Connect drain line to air gap, waste tee or disposer FOLLOWALL LOCALCODESAND ORDINANCES. using either previously determined method. The drain hose molded end will fit 5/8", 3/4" or 1" Method 1 - Air gap with waste tee or disposer diameter connections on the air gap, waste tee or __ re __ re disposer. Cuton the marked line as required for your installation. Cutting Lines FigureU 4 Waste Tee Installation Disposer Inst
ページ11に含まれる内容の要旨
Installation Instructions ISTEP 141 CONNECT POWER ISTEP 15] PRE-TEST CHECKLIST SUPPLY Review this list after installing your dishwasher to avoid charges for a service call that is not covered Skip this step if equipped with power cord, by your warranty. Verify that power is turned off at the source. • Remove junction box cover "A". [] Check to be sure power is OFE • Locate the three dishwasher wires, (white, black and [] Open door and remove all foam and paper green) with stripped ends. Insert d
ページ12に含まれる内容の要旨
Installation Instructions ISTEP 161 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK [] Turn on power supply (or plug power cord into outlet, if equipped). [] Turn dial to Normal "Wash" position. [] Close door. [] Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, checkto be sure that water and power are turned on. [] Check for leaks under the dishwasher. If a leak is found, turn power supply off, then tighten connec- tions. Restore power after leak is correcte
