ページ1に含まれる内容の要旨
(1,1) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM (1,1) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM
Installation instructions
DishDrawer®
DD36S models
US CA
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our
local website listed at the end of this document or contact your loc
ページ2に含まれる内容の要旨
Integrated DD36STI Prefi nished DD36SDFTX Integrated DD36STI Prefi nished DD36SDFTX (1,2) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM (1,2) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM 23 PRODUCT DIMENSIONS CABINETRY DIMENSIONS Installation diagrams for illustration purposes only I B B C F A D C I G J E H A K C I B 11⁄16” B B (18 mm) L G I E 13⁄16” (20 mm) H 1” (2.5 mm) Cabinetry dimensions (inches (mm)) Product dimensions (inches (mm)) A overall height of product
ページ3に含まれる内容の要旨
Water supply (2,1) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM (2,1) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM 4 PARTS SUPPLIED Side mounting Edge protector (1) Drain hose Drain hose Wire clip (1) Clamp (1) Phillips Rubber Moisture protection 1½ ” (38 mm) bracket kit support (1) joiner (1) 5⁄8 ” (16 mm) washer for tape (1) (if services hole bottom (A and B) (2) partition is metal) screws (7) inlet hose (1) (to prevent moisture fixing screws damage) & meta
ページ4に含まれる内容の要旨
(2,2) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM (2,2) -1- 599796A DD36S installA2 USCA.indd 19/2/10 11:32:01 AM 6 OPTIONALLY HARD WIRING THE PRODUCT Mark the placement in A B case the chassis moves. Remove the access cover 4 6 1 Ensure the drawer is removed and then rotated counter- 7 clockwise to prevent kinked hoses. 8 10 2 9 Remove Power supply 5 3 10 9 C D Use copper conductors only. 17 Ensure the drawer is now rotated clockwise back. 13 19 18 Before refitting the
ページ5に含まれる内容の要旨
(1,1) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM (1,1) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM RECOMMENDED METHOD - SECURE WITHOUT ALTERNATIVE METHOD - DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) SECURE BY DRAWER REMOVAL 7 7 ROUTE HOSES & POWER CORD ROUTE HOSES & POWER CORD & MOVE INTO CAVITY OR 2 Tie together to avoid kinking. 1 Tie together to avoid kinking. OR 4 3 4 1 2 Ensure hoses and cord are not kinked or twisted. 88 REMOVE DRAWER ATTACH SIDE MOUNTING BRA
ページ6に含まれる内容の要旨
(1,2) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM (1,2) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM 5 slot and ‘B’ bracket must match ‘B’ slot. 3 99 MOVE INTO THE CAVITY SECURE THE DRAWER The product has three pairs of fixing points: (Refer to 4 for relevant parts) 2 1 Ensure the sound insulation is repositioned correctly. 1 2 a pair of fixing holes either side on the bottom (use 1½ ” (38 mm) fixing screws & washers) 2 two pairs of formed Ensure hoses and
ページ7に含まれる内容の要旨
29 ½ ” - 34 ¾ ” (750 - 882.5 mm) 29 ½ ” - 34 ¾ ” (750 - 882.5 mm) (2,1) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM (2,1) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM 11 PLUMBING AND DRAINAGE OPTIONS DishDrawer® with Waste Disposal DishDrawer® using Air Break DishDrawer® and Standpipe AB C with Drain Hose Joiner Ø 1 ½ ” (38 mm) If space is limited for fixing, push If space is limited for fixing, push hose through drain hose support hose through drain hose
ページ8に含まれる内容の要旨
(2,2) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM (2,2) -2- 599796A DD36S installA2 USCA.indd 19/2/10 11:33:29 AM 12 FINAL CHECKLIST 13 TROUBLESHOOTING Check all parts are installed. Excessive water remaining above the filter plate, after the rinse cycle Ensure product is level, securely fastened to the cabinetry and opens and closes Check for a kinked drain hose or blocked waste connection, highloop not freely. The DishDrawer® must be free to fully close with no resistance
