ページ1に含まれる内容の要旨
Danby Products Ltd°
DDW1802 DDW1805
SERVIC_ MANUAL
/
/
ページ2に含まれる内容の要旨
BHDEX t, PRODUCT SPECIFICATIONS 2, SCHEMATIC DIAGRAM 3. WiRiNG DIAGRAM 4, TIMER CYCLE CHART 5, COMPONENT OPERATION AND REPAIR 6, TROUBLE SHOOTING 7, PARTS LiST AND DIAGRAM
ページ3に含まれる内容の要旨
SPECIFICATION MODEL and DDW1805 DDW1802 ELECTRICAL 120V 60Hz 115 Motor (HP) Motor (Amps) 1000W Heater Wattage Wash 9,2A Total Amps (Load Rated) 127°F +5°F Thermostat Contacts Close at 58-+3_- WATER SUPPLY 120°F to 150°F Suggested Min. Incoming Water 49_-to 66__= 15/120 PSI Pressure (PSi) MinimumlMaximum 318" 3.5+5% _Consumption (Toil Gallons) LWater Valve Flow Rate (GPM) , 1.08GPM+10%
ページ4に含まれる内容の要旨
Library Imaging System DDW1802W AND DDW!80SW Schematic Diagram of Dishwasher _G IS T-T-T-i ,eLi ....... I....... ! '_-" CEM_O,,BqF O,m Q.',n[acl o! tim-¢ I Ck I i , _ i_ I I I L IS 13r'xmt s,,',_ t ch I .... m.!\ i I I i LSBO LSS_ i} g t .... _ LS 0 _in pukka ,_/,ssi L____ t I I ----q t LZJ CL_ IAC8 I t R t_se _ d ',_r ni t_g _ i _'_t • I
ページ5に含まれる内容の要旨
U_r_ ImagingSystem J .J
ページ6に含まれる内容の要旨
Library Imaging System D37_I802WAt',D EL_1805WRograrre Oycl e of I3 shwsher I l:_,:t-A-I T_................."--_--_-, = =-= -= r_ __ :;I;::_-_i:;_,22_!}] _I]I]t _q-!t1] It -_-iI t li I1I?1-il li _--._,, 00o, _o,u,0,,o,, ol,_ l!I&l I,.60,.h,l_._.o,, _t_I ,t_ .!l,,._ijo i.J LI,
ページ7に含まれる内容の要旨
Library Imaging System COMPONENT OPERATION AND REPAIR SAFETY PRECATIONS Always turn off the electric power supply before servicing any electrical component,makingohmmeterchecks,or replacinganyparts., All voltage checks should be made with a voltmeter having a full scale range of 130 volts or higher. After service is completed, be sure all safety-grounding circuits are complete, a!t electrical connections are secure, and all access panels are in place. TIMER With the timer, user selects the vario
ページ8に含まれる内容の要旨
Library Imaging Sysf,em Figure 1 Figure 2 ., Remove the screws which locking the control panel (See figure 1) Remove the knob and unscrew the two screws which locking the timer on the control panel (See Figure 2,) 4 Take down the damaged timer and JnstalJ a new timer, reverse procedures to complete re ure 3and 4,) Figure 3 Figure 4 DOOR LATCH AND SWITCH ASSEMBLY the control panel The The latch and switch are located in the door assembly behind dishwasher will not operate until the door is closed
ページ9に含まれる内容の要旨
Library imaging System Figure 5 4. Install new door latch assembly and reverse procedures to complete repairs,, FLOAT SWITCHASSEMBLY The water float assembly is located in the right lower side of the dishwasher (the portable located behind the lower front crosspiece).. When too much water enter the dishwasher, the water will enter the float support through the overflow pipe, the float will make the floating .switch acts, the electrical supply to the water valve will disconnected and the drain pu
ページ10に含まれる内容の要旨
Library imaging System TROUBLESHOOTING The troubleshooting cheek list is common for all dishwasher models° They use different parts to accomplish the same thing and diagnosis wilt remain similar° When a problem arises, and a possible cause is listed, follow the test, remove or replace procedures as outline in this service manual, The wiring diagram, shematic and timer cycle chat is a necessity when maklng electrical checks. In most cases an ohmmeter will handle all _he tests necessary. For check
ページ11に含まれる内容の要旨
Library Imaging System Repeated dishwash_- •Timer (contact's o_p'en or burnt) Replace timer cycles =Motor (inoperative, check Replace timer resistances): ......... Timer does not advance Replace timer .Timer motor (stalled or open). automatically .Check timer for power to timer Replace timer motor. Repair or adjust =Timer shaft bindinl] or knob interference to escutcheon. Dishwa"sher wii'i not fili •Water supply turns off Turn water supply on. with water, • Defective inlet valve, Replace inlet v
ページ12に含まれる内容の要旨
Library Imaging System Instruct customerluser on • Improper loadlng of dish'esi-lOO"_" and other,, proper loading per owner' s guide ,,Heating element (open), • incoming water temperature too Replace heating element low, Incoming water temperature of • Wiring or terminal (broken or t40°F for best drying results. I Replace or repair. burnt) .... ..... tergentcupwi, not • Cup binding. Repair or replace. Replace pin, retainer or shaft • Roll pin retainer or shaft broken. open. =Defective bi-metal.
ページ13に含まれる内容の要旨
Library Imaging System 620000190! 6060200800 6060120_00(=040_0!_0!G0602100006060100600 rirgrut d _r tr_ Orirg _ir l:r_:_" // 60601000_]0 d_zin h:se d // s_t _o/, 6200002600 1_300!00// / h_irg de"E_ts / OrirgfcrgJ_ r_r b'aS_ ml:fiN _n_/ forpdscUm/" _______L_ / tt_n_t a lxdedim d'ai n h:_e
ページ14に含まれる内容の要旨
Library Imaging System
ページ15に含まれる内容の要旨
Library Imaging System
