ページ1に含まれる内容の要旨
ECP190 / ECP290 ECP190 / ECP290
DOOR CONTROLLERS DOOR CONTROLLERS
STAND ALONE
ACCESS CONTROL
Site Coded & Site Coded & Sequentially Sequentially
Number Numbered Access Passes ed Access Passes
for Security for Security, Identification & , Identification &
Operational Integrity Operational Integrity..
®
nacd.co.uk
ページ2に含まれる内容の要旨
ECP190 / ECP290 ECP190 / ECP290 DOOR CONTROLLERS DOOR CONTROLLERS ® Explanation of Noralsy Access Passes 3 General Door Controller Information 4 ECP 190 Door Controller schematic 5 ECP 290 Door Controller schematic 6 ™ How to use the Telpro programmer 7-8 Programming Set-up on installation 9-10 Block loading of Access Passes 10 Deleting individual Access Passes 10-11 Validating individual Access Passes 11 Block deletion of Access Passes 11 Changing lock output time 11 Changing the Master Code 11
ページ3に含まれる内容の要旨
NORALSY® ACCESS PASSES Numbered ALL ACCESS PASSES ARE KCP3 Proximity Key VISIBLY NUMBERED The number of each and every Access Pass is visible. Just by looking at it, ® you know which Access Pass you have. Noralsy pre-number each Access Pass because this is the only way you can know for sure what you have received, what you need to program the system to accept (or, reject in the case of loss, theft or non-return) and, who has been issued with which TELBIP Numbered Access Pass. or TELBIPHF ALL A
ページ4に含まれる内容の要旨
1 2 3 1 2 3 4 5 Noralsy ECP Door Controllers ® –If NOT Monitoring Door Open/Closed Status IMPORTANT OR ECP ALARM ELEC/INST/800 BUZZES CONTINUOUSLY 654321 65432 1 ON 1 ECP Door Controller Standardisation of Terminal Numbering Place Noralsy unit on a flat surface with PCB facing skywards. o View terminal blocks from the outside looking in. Terminal N . 1 is always the first on the left of every terminal block strip. 1 2 1 2 3 1 2 3 4 1 2 3 4 5 1 2 3 4 5 6 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 1 2 3 1 2 1
ページ5に含まれる内容の要旨
ECP190 Door Controller for 0 1 n Door/Access Point ■ Capacity 999 Users ® ELEC/INST/801 ECP 190 Door Controller Supply 12V DC ± 10% Dimensions 103 L x 106 W x 83 D (6 DIN units) Weight 0.44 Kg Power Consumption 55mA quiescent 32 1 2 1 (—) (+) CE Norms EN50082, EN55022 Class B 32 1 32 1 21 1 5 2 4 3 3 4 2 5 1 1ON 12345 6 123456 = 12345 6 = If not used, link terminals 3 & 4 to create a permanently closed circuit. 5
ページ6に含まれる内容の要旨
ECP290 Door Controller for 0 2n Doors/Access Points ® ■ Capacity 999 Users per door ELEC/INST/830 ANTI-PASSBACK FEATURE AVAILABLE ECP 290 Door Controller Supply 12V DC ± 10% Dimensions 163 L x 106 W x 83 D (10 DIN units) Weight 0.56 Kg * If not used, link terminals 3 & 4 to Power Consumption 160mA quiescent create a permanently closed circuit. CE Norms EN50082, EN55022 Class B 6
ページ7に含まれる内容の要旨
Programming Stand-Alone Access Control Systems using TELPRO™ Programmer. ® TELPRO™ PROGRAMMER Access Control Modules with integral Infra-Red MLP3 Proximity The TELPRO™ Programmer is a handheld ® keypad used for programming Noralsy The TELPRO™ Programmer stand-alone access control systems. can be used as a wirefree infra-red programmer. Simply o Installation companies only ever need 1n . point at the reader/receiver TELPRO™ Programmer. module to program. TELPRO™ can be used on any system provided
ページ8に含まれる内容の要旨
™ Programming using TELPRO as a remote wire-free programmer. Remote Programming Range: Infra-Red Receiver 20 cms - 5 metres Proximity Reader 5 cms - 10 cms How to use the TELPRO: Important: Flick TELPRO switch to ON - Red LED on the right must light up. Dimensions (mm): Each press of a button (Remember to turn unit off when finished) 120L x 60W x 25D is confirmed (as received) by the reader/receiver by a Point TELPRO at the reader/receiver. single beep. Press the ™ TELPRO buttons gently. Ent
ページ9に含まれる内容の要旨
ECP Door Controller with PROGRAMMING ACCESS PASS CONTROL TOP POINTS TO REMEMBER ■ Programming is effected via the TELPRO programming keypad. ■ Site Code is always a 5 digit number. o ■ Site Code is always stored in Slot N . 01. ■ Master Code (Programming Access Code) is always a 5 digit number. o ■ Master Code is always stored in Slot N . 06. TIP - WHEN YOU ARE PROGRAMMING It is a good idea to have written down in advance what you want to program. Enter the numbers in quick succession after a b
ページ10に含まれる内容の要旨
STEP 4 You must now inform the Door Controller of the Site Code of the Access Passes supplied. o The Site Code is always stored in Slot N . 01. The Site Code is always a 5 digit number. Check the Access Pass Information Sheet delivered with the Access Passes. It will tell you the Site Code of the Access Passes delivered. * Example: Site Code = 45801 After a beep enter on the TELPRO: A sharp beep confirms that you have correctly entered the Site Code. Programming mode beep - every 4 seconds -
ページ11に含まれる内容の要旨
After a beep enter on the TELPRO: A sharp beep confirms that you have correctly deleted Holder Number 074. Programming mode beep - every 4 seconds - resumes. o Example C: Validation of 1n . Access Pass You have just received the additional Access Pass ordered for Alan Jones who had lost his earlier in the week. The last o 3n . digits on the Access Pass are 176. Alan Jones is now Holder Number 176 and you have to program the system to accept Holder Number 176. Enter the Master Code 19388 on the
ページ12に含まれる内容の要旨
ECP290 DOOR CONTROLLER FOR 2 DOORS – IMPORTANT INFORMATION FLICKING PROGRAMMING SWITCH SW1. The access control readers on both doors will start to beep every 4 seconds indicating programming mode status. Only o 1 n . access point (door) can be programmed at a time. IF USING THE TELPRO PROGRAMMER IN WIREFREE INFRA-RED MODE: Simply point at the relevant reader to effect programming for its related access point (door). Repeat the process for the 2nd access control reader on the ECP290. Remember to
ページ13に含まれる内容の要旨
Mode 4 - Dual Security, Access Pass + Keypad Code 00400508 = Set-Up, Mode 4 È Relay output time in seconds User required to present a valid access pass and then enter a valid code or vice versa in order to gain access. A o maximum of 27n .5 digit keypad codes can be set at any one time. Any 1no. of these keypad codes together with a valid access pass is sufficient to gain entry. This feature is also available on the ECP190 Door Controller. Mode 5 - Anti-Passback 00500508 = Set-Up, Mode 5 È Relay
ページ14に含まれる内容の要旨
Noralsy® ECP Door Controller ® ® Fail Safe Locking + 32 1 32 1 21 (—) (+) ECP190 Door Controller ELEC/INST/802 Automation Control / Volt Free 32 1 32 1 2 1 ECP190 Door Controller ELEC/INST/803 Entrance/Exit Access point requiring access control on both sides of the door, gate or barrier. 1 2 3 4 5 6 6 5 4 3 2 1 ie. Access Pass to be presented to enter and again to exit through the same control point. Note: In this type of installation, programming can take place via the TELPRO programmer at eith
ページ15に含まれる内容の要旨
Noralsy® ECP Door Controller ® ® Locking 32 1 32 1 21 (–) (+) ECP190 Door Controller ELEC/INST/805 DIN Rail Mounting DIN Rail ELEC/INST/806 Wall Mounting ELEC/INST/807 15
ページ16に含まれる内容の要旨
Noralsy® DIN Rail Power Supplies ® ® ARE121 12V AC/DC ARE122 12V DC 1 AMP MAXIMUM OUTPUT 2 AMP MAXIMUM OUTPUT ELEC/INST/808 ELEC/INST/809 ARS122 12V DC AB126 BATTERY STANDBY 2 AMP MAXIMUM OUTPUT ELEC/INST/811 ELEC/INST/810 16
ページ17に含まれる内容の要旨
Noralsy® Powering ECP Door Controller(s) using Noralsy® DIN Rail Power Supply Units ® ARE121 + ECP190 ELEC/INST/812 ARE122 + ECP290 ELEC/INST/812A 17
ページ18に含まれる内容の要旨
ECP190 DOOR CONTROLLER with KEYPAD ACCESS CODE CONTROL TOP POINTS TO REMEMBER ■ Programming is effected directly via the keypad. ■ Master Code (Programming Access Code) is always a 5 digit number. o ■ Master Code is always stored in Slot N . 06. ■ Keypad Access Codes are always 5 digit numbers. os ■ Keypad Access Codes can be stored in Slot N . 03 - 05 and 07 - 30 only. SET-UP ON INSTALLATION Proceed exactly as detailed before in section ECP Door Controller with Access Pass Control. Stop when y
ページ19に含まれる内容の要旨
After a beep enter on the keypad: A sharp beep confirms that you have deleted Alan’s code. Programming mode beep - every 4 seconds - resumes. After a beep enter on the keypad: A sharp beep confirms that you have deleted Alex’s code. Programming mode beep - every 4 seconds - resumes. Note 1. You do not need to know the actual code itself which needs to be deleted, only the Slot Number in which it is stored. Note 2. Capacity is never reduced as a result of deleting codes. You can always add or ch
ページ20に含まれる内容の要旨
ARE122 POWER SUPPLY ECP 190 DOOR CONTROLLER Input 85VAC - 264VAC Supply 12V DC ±10% Output 12V DC - 2AMP Dimensions 103 L x 106 W x 83 D (6 DIN units) Dimensions 160 L x 106 W x 85 D (10 DIN units) Weight 0.44 Kg Weight 0.5 Kg Power Consumption 55mA quiescent CE Norms EN55022 Class B, EN 60950, UL 94 VO CE Norms EN50082, EN55022 Class B ARS122 POWER SUPPLY WITH STAND-BY FACILITY ECP 290 DOOR CONTROLLER Input 85VAC - 264VAC Output 12V DC - 2AMP Supply 12V DC ± 10% Dimensions 160 L x 106 W x 85 D
