ページ1に含まれる内容の要旨
0 0
.
.
DJLab 1.1
3
3
5
5
.
.
5
5
0
0
ページ2に含まれる内容の要旨
IMPORTANT SAFETY PRECAUTIONS 1. Read Instructions – All the safety and operating instructions should be read 14. Servicing – The user should not attempt any service to the appliance beyond before this product is operated. that described in the operating instructions. All other servicing should be 2. Retain Instructions – The safety and operating instructions should be retained referred to qualified service personnel. for future reference. 15. Ventilation – Slots and openings in the cabinet are
ページ3に含まれる内容の要旨
M.212 INTRODUCTION Thank you for purchasing Stanton’s newest innovation in professional tabletop mixer. The M.212 mixer was designed to bring style and reliability to the mobile or club DJ at an affordable cost. M.212 MAIN FEATURES 2 bend EQ w/ input GAIN control per channel. Fader Start Power on/off muting Long Life crossfader Crossfader curve control M.212 ACCESSORIES Checking Package Contents Check that the ca
ページ4に含まれる内容の要旨
M.212 CONTROL OVERVIEW TOP PANEL 1. Channel Gain - Adjusts the pre-fader volume for cleaner sound. 9. Headphone Input - Insert your ¼” headphone plugs here. Reduce the channel gain if you notice the level indicators flashing red. 10. Fader Start On/Off Switch - When the unit has been connected 2. Mic Input Gain - Adjusts microphone input level. to a CD player using a control cable, this becomes the On/Off switch to automatically start and stop the CD player while using th
ページ5に含まれる内容の要旨
M.212 CONTROL OVERVIEW REAR PANEL 16. Power Switch - Turns unit off and on. 17. Power Connector - Plug in the included power supply here. 18. Fader Start Control Jacks - Connect these jacks to the Fader input jacks of the CD player using the 3.5mm stereo mini cord. 19. Master Output - Unbalanced RCA connectors controlled by the Master level. 20. Line Inputs - Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players, HiFi VCRs, cassette d
ページ6に含まれる内容の要旨
M.212 QUICK SETUP DIAGRAM Review this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources and processors. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC power. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input sources, such as turntables or CD player
ページ7に含まれる内容の要旨
M.212 SPECIFICATIONS Input / output impedance & sensitivity: (Master 0dBV output, load=100Kohm, Max. gain, EQ flat) Line 10K ohm /-14dBV (200mV) +/-2dB Phono 47K ohm /-50dBV (3.16mV) +/-2dB Mic 2.2K ohm /-60dBV (1mV) +/-2dB Master 1K ohm Phones 33 ohm / 0dBV (1V) ±2dB Max. output (THD=1%, Maximum gain, EQ flat) Master More than +18dBV (8.0V) at load=100K ohm Phones More than +4dBV (1.6V) at load=32 ohm Channel balance Within 3dB Frequency response: (Master o
ページ8に含まれる内容の要旨
T.52 ASSEMBLY Thank you for purchasing the T.52 turntable from Stanton. The T.52 is built upon Stanton’s heritage of designing audiophile products for the most discriminating listener. Before assembling the T.52 please check to make sure the following items are included with the main unit in the carton. AC cord Slipmat RCA cable Stanton 500.V3 Cartridge pre-mounted on headshell, 45 rpm adaptor except on model T.52X, no cartridge included Counter weight User Manual C
ページ9に含まれる内容の要旨
0 1.0 T.52 TONEARM AND CARTRIDGE SETTING The major cause of problems in sound and skipping on the vinyl is the lack of proper set up of the needle and turntable adjustments. The needle is designed to operate at a specific angle to the vinyl. The T.52 has two adjustments to correctly position the needle to the vinyl. 1. The first adjustment is the installation of the cartridge-head-shell assembly into the tone arm tube lock. The T.52 includes a Stanton 500 V3 cartridge pre-mounted to Locki
ページ10に含まれる内容の要旨
T.52 CONTROL OVERVIEW 8. Pitch slider - Use this to change the speed of the platter when the PITCH 1. Start/Stop - Press this button to start or stop the platter. indicator is lit. 2. Strobe dots - The dots around the edge of the platter are used in 9. Headshell locking nut - Attach headshell by inserting into the front end of conjunction with the light located inside the motor ON/OFF
ページ11に含まれる内容の要旨
T.52 SPECIFICATIONS GENERAL Model: T.52 Dimensions 452(W) x 370(D) x 87(H)mm Weight 5.4Kgs Power supply AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A., Canada, Mexico) AC 220V, 50Hz (For United Arab Emirates, Chile, Argentina) AC 220V, 60Hz (For Philippines) AC 230V, 50Hz (For Europe, New Zealand, South Africa, Singapore, Israel) AC 240V, 50Hz (For Australia, U.K.) Power consumption 5.5W WARRANTY & RETURN POLICY Warranty Through Sta
ページ12に含まれる内容の要旨
Copyright © 2008 Stanton Magnetics, Inc. DJLab, M.212, T.52, and T.62 are trademarks of the Stanton Group. All other trademarks are property of their respective owners, who are not affiliated with Stanton DJ. All information included in this User Manual is subject to change without notice. www.stantondj.com - +1.877.578.6866 LITS00020 REV-B 11/18/2008
