ページ1に含まれる内容の要旨
OPERATORS MANUAL TTM 56S
PERFORMANCE MIXER
Quick Start
Congratulations! You are the proud owner of an exceptional per-
formance instrument. Experienced turntablists will find the TTM
56S comfortable and familiar. The TTM 56S has many unique
features which are mastered quicker if you read the manual. Right!
We know you can’t resist jumping right in, but please read at least
this portion of the manual. It will help you get a good start.
About the faders: The program faders and crossfader are m
ページ2に含まれる内容の要旨
Rear Panel Hook-up COMMERCIAL AUDIO TTM 56S EQUIPMENT 24TJ MADE IN U.S.A. RANE CORP. R U.S. PATENT 6,813,361 ACN 001 345 482 PHONO MASTER MIC GROUNDS FlexFX OUTPUTS BALANCED AUX PGM 2 PGM 1 L L OUT IN 4 3 2 1 L L L L RETURN SEND PHONO EFFECTS 4321 R R 1 2 3 4 O N R R R R 100-240V 50/60 Hz OUT IN 4 3 2 1 BALANCED UNBALANCED 4321 TIP = SEND 20 WATTS LINE RING = RTN Power Effects Loops Outputs The TTM 56S features an internal MIC EFFECTS insert jack is unbal- AUX OUT may be used for recording,
ページ3に含まれる内容の要旨
Mic Section MIC LEVEL sets the gain of the PGM 1 PGM 2 Mic Input. The range is off to +44 OUTPUT 4 6 4 6 LEVELS dB. There is no engage switch, so set 4 6 1 2 2 8 2 8 3 4 4 6 the Mic Level to zero (0) when you 2 8 SOURCE 0 10 0 10 SOURCE 2 8 GAIN GAIN aren't using it. The Mic Input mini- 0 10 0 10 MIC LEVEL OL MAIN mum gain is 26 dB, so a line-level mic 4 6 source (such as a wireless receiver) L R L R 2 8 OFF +6 OFF +6 HIGH PAN PAN HIGH must be padded. -12 +12 0 10 IN IN MIC HIGH AUX OUT EQ
ページ4に含まれる内容の要旨
• The headphone output of the TTM Faders Headphone Cueing 56S delivers very high volume. The program faders and crossfader PHONES Level control sets the out- are magnetic, non-contact faders. This put level of the headphone amplifier. • To avoid pain, never put headphones means No travel noise or bleed ! The on your head before plugging them in. MASTER / CUE switch is used to electrical performance of the faders select the headphone monitor source: • Always start with the PHONES Level
ページ5に含まれる内容の要旨
Fader Response SLOW FAST SLOW FAST FADER 1 CONTOUR REVERSE FADER 2 CONTOUR REVERSE FULL ON FULL ON OFF OFF SLOW FAST SLOW FAST FADER 1 CONTOUR REVERSE FADER 2 CONTOUR REVERSE OFF OFF FULL ON FULL ON SLOW FAST SLOW FAST CROSSFADE CONTOUR REVERSE CROSSFADE CONTOUR REVERSE Channel faders and Crossfader illustrating the effects of the Reverse and Contour controls. Manual-5
ページ6に含まれる内容の要旨
Magnetic Fader Q and A Maintaining Magnetic Faders Q: Will I damage the faders if I spray them with bad stuff or There are no electrical contacts to clean! spill bad things in them? The faders in the TTM 56S are designed with materials highly A: No. The faders in the TTM 56S are designed with materials resistant to corrosion and most chemicals. While the faders will highly resistant to corrosion and most chemicals. There are no handle millions of operations, they may become dirty over time. e
ページ7に含まれる内容の要旨
Fader Removal For more effective cleaning and lubrication, follow the directions outlined below: 1. Required tools: #1 Philips screwdriver and a pair of clean hands. 2. Disconnect the power. 3. Remove the fader caps by pulling them away from the Lexan faceplate. 4. Remove the four 4-40 screws attaching the Lexan faceplate. 5. Remove the Lexan faceplate. See the picture and instructions. The fader rails are now accessible for normal cleaning and lubrication. 6. If more thorough cleaning is requi
ページ8に含まれる内容の要旨
TTM 56S Block Diagram ©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5000 USA TEL 425-355-6000 FAX 425-347-7757 WEB www.rane.com 111500 Manual-8 OL GAIN OFF+44 dB MIC EFFECTS MIC INPUT +12 EQ TIP = SEND -12 RING = RETURN LOW HIGH RIAA +5 PHONO CH 1 FLEXFX PGM 1L LINE PGM 1 GAIN TRIM OL LEFT -12 +12 EQ CH 1 LEFT VCA KILL +6 FLEXFX LOOP 1 SOURCE SEND OFF CHANNEL 2 ON SWAP RIAA LOW MID HIGH CH 1 BAL CH 1 VCA RIGHT PHONO LINE PGM 2 CH 1 RIGHT LEFT DRY MIX LEFT CH 1 FADER CONTOUR T
