ページ1に含まれる内容の要旨
PS/2 Mouse
SPP/EPP/ECP Parallel Port
Speaker Out
Connector
RJ45 10/100
LAN Jack
(Optional)
PS/2 Keyboard
FAN3 Connector
USB Port COM 1 Port COM 2 Port Line-In MIC-In
Connector
AUX-IN Connector
CD-IN Connector
FAN2 Connector
Intel 82550 10/100 LAN
1500 F Low ESR Capacitors
Controller
CPU1 FAN connector
CPU2 FAN Connector
AGP Pro Slot
USB Connector
Dual CPU sockets
CPU #2
CPU #1
FAN1 Connector
32 Bit PCI Slot x 5
4Mbit Flash BIOS
ATX 20-pin Power Connector
Game Port C
ページ2に含まれる内容の要旨
1. JP14 Clear CMOS You can clear CMOS to restore system default setting. To clear the CMOS, follow the procedure below. 1. Turn off the system and unplug the AC power. 2. Remove ATX power cable from connector PWR2. Everything you need to boot this 3. Locate JP14 and short pins 2-3 for a few s econds. motherboard is included in this Easy Installation Guide. For more 4. Return JP14 to its normal setting by shorting pin 1 & pin 2. information, a complete Online 5. Connect ATX power cabl
ページ3に含まれる内容の要旨
3. Installing Processor 5. Setting CPU Voltage & Frequency Setting CPU Core Voltage This motherboard supports CPU VID function. The CPU core voltage will be automatically 1. Pull up the CPU socket level and up to CPU socket lever detected and the range is from 1.05V to 1.825V. It is not necessary to set CPU Core Voltage 90-degree angle. Setting CPU Frequency 2. Locate Pin 1 in the socket and look for a This motherboard is CPU jumper-less design, you can set CPU frequency throu
ページ4に含まれる内容の要旨
6. Support Four USB Connectors 8. Connecting IDE and Floppy Cables This motherboard provides four USB connectors to connect USB devices, such as Connect 34-pin floppy cable and 40-pin, 80-wire IDE cable to floppy connector FDC and mouse, keyboard, modem, printer, etc. There are two connectors on the PC99 back IDE connector. Be careful of the pin1 orientation. Wrong orientation may cause system panel. You can use proper cable to connect other USB connectors to the back panel or damag
ページ5に含まれる内容の要旨
10. Connecting 68-pin Ultra 160 SCSI Cable 12. Connecting CD / AUX Connector ) The DX37Plus-U provides two 68-pin Ultra Wide/Ultra 2/3 SCSI connectors for 16-bit or The AUX-IN connector is used to connect MPEG CD-IN (Black) 16-bit differential SCSI devices. Audio cable from MPEG card to onboard sound. The CD-IN connector is used to connect CD Audio cable from CDROM or DVD drive to onboard sound. AUX-IN (Green) Disable SCSI Ch A SW1(3) On Terminator Disable SCSI Ch B Connector P
ページ6に含まれる内容の要旨
16. Wake On LAN 14. Support 10/100 Mbps LAN onboard To use Wake On LAN function, you must have a network card with chipset that supports this The South Bridge V8233 of VIA Apollo Pro266T chipset includes a fast Ethernet controller on feature, and connect a cable from LAN card to motherboard WOL connector. The system chip. On the strength of Intel 82550 PHY on board, which is a highly-integrated Platform LAN identification information (probably IP address) is stored on network card and
ページ7に含まれる内容の要旨
Part Number and Serial Number If you encounter any trouble to boot you system, follow the procedures The Part Number and Serial number are printed on bar code label. You can find this accordingly to resolve the problem. bar code label on the outside packing, on ISA/CPU slot or on component side of PCB. For example: Start Turn off the power and unplug the AC power cable, then remove all of the addon cards and cables, including VGA, IDE, FDD, COM1, COM2 and Printer. Part No. Serial No
ページ8に含まれる内容の要旨
Online Manual: Please check the manual carefully and make sure the jumper s ettings and installation procedure are correct. 1 1 http://www.aopen.com.tw/tech/download/manual/default.htm Dear Customer, Test Report: We recommend to choose board/card/device from the Thanks for choosing AOpen products. To provide the best and fastest service to compatibility test reports for assembling your PC. our customer is our first priority. However, we receive numerous emails and 2 2 http://www.aope
