ページ1に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 1
NetCam2
Eng
Lens optional
Default IP address: 211.53.133.92
Administrator login: Password: admin
ID: admin
User login: Password: guest
ID: guest
Philips
Communication,
Security & Imaging
Installation Instructions
ページ2に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 2 NetCam2 Safety IMPORTANT SAFEGUARDS 1. Read Instructions: All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions: The safety and operating instructions should be retained for future reference. 3. Heed Warnings: All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions: All operating and use instructions should be followed. 5. Cleaning: Unplug
ページ3に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 3 NetCam2 Safety 12. Damage Requiring Service: Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions. If liquid has been spilled, or objects have fallen into the unit. If the unit has been exposed to train or water. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjus
ページ4に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 4 NetCam2 Safety SAFETY PRECAUTIONS This label may appear on the bottom of the unit due to space limitations. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN! CAUTION:TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with an arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated
ページ5に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 5 NetCam2 Contents TABLE OF CONTENTS IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 6 NetCam2 Contents TABLE OF CONTENTS 4.2 Administrator’s page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 4.2.1 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 4.2.2 User Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 4.2.3 Network Configuration . . . . . . . . . . . . . . . . . . . . . . . .
ページ7に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 7 NetCam2 Section 1 1 INTRODUCTION NetCam2 is a network-based high-resolution digital network camera for CCTV applications. It contains an integrated Internet server and connects directly to an Ethernet network. No other hardware is necessary. NetCam2 provides real-time color pictures from up to two cameras over the Internet using an image compression format. 1.1 Description The microprocessor-based NetCam2 contains a digital color camera, web ser
ページ8に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 8 NetCam2 Section 1 1.2 Unpacking Unpack carefully and handle all electronic equipment with care to prevent damage. Check for the following items: • NetCam2 - Web Camera Server • Crossover cable, 1 m (red) • Direct cable 2 m (white) • Adapter & Power cable (12V DC, 1.5 A) • Software • Manual Note: Save the packaging materials for future use if the unit needs to be shipped for service or repair. 1.3 NetCam2 Rear View and Descriptions Zoom lens con
ページ9に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 9 NetCam2 Section 1 Connector Description Remark name Video Output of internal camera or input for channel 2 as set by DIP switch Zoom Lens To control zoom and focus adjustment. +/-6V drive voltage with common ground Network To connect 10 Base-T Ethernet cable Iris Lens Video Iris lens connector DIP switch Left: To designate video signal termination of ‘Video Input’ BNC connector Right: To select BNC function as input or output AC 24V/DC 12 V T
ページ10に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 10 NetCam2 Section 1 Description on LED of Ethernet Port Yellow LED Green LED Yellow LED: This LED indicates the status of data transmission. After power is supplied, it is on for the first 4-5 seconds and then it goes off. It blinks continuously when NetCam 2 transmits data. Green LED: This LED indicates the status of networking. After power is supplied, it is on for the first 1-2 seconds, and then it blinks once at every one second as long as th
ページ11に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 11 NetCam2 Section 2 2 INSTALLATION 2.1 Installation summary • Connect Ethernet and power to the NetCam2 on a local network for configuration (see 2.1.3). • Install the setup program for NetCam2 (see 2.2). • Assign an IP address to NetCam2 and configure its network settings (see 2.3). • Configure the operational settings (see 2.4). • Install NetCam2 in its location, and re-connect the power and Ethernet. • Adjust the focus (see section 6). 2.1.1 S
ページ12に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 12 NetCam2 Section 2 2.1.4 Connecting NetCam2 to a PC using crossover cable Crossover cable (red) Select 'IP Address' FIgure 2-2 Connecting NetCam2 to a PC using a crossover (cross link) Network cable. 2.1.5 Connecting NetCam2 to a PC via a HUB HUB 2 FIgure 2-3 Connecting NetCam2 to a PC via a HUB, using ‘Direct’ cables. 12
ページ13に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 13 NetCam2 Section 2 2.1.6 PSTN dial-in connection 1. Connect a PSTN modem to the NetCam’s RS232 serial port. 2. Ensure that the modem is selected as connected device in the Serial Configuration screen of the Administrator’s pages. 3. On the client side use a recommended browser with dial-up connection. 4. In the dial screen enter username/password of the NetCam. (default is guest or admin). 5. To view the NetCam pages enter IP address 10.0.0.10 i
ページ14に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 14 NetCam2 Section 2 2.3 Assigning IP Address and Starting Configuration It is possible to setup a NetCam2 that is either connected to a local network or directly connected to a PC using the red-colored crossover cable (supplied). When setup is executed, the table lists all NetCam2s connected to the local network. • Select the ‘MAC address’ of the NetCam2 requiring an IP address. • When a NetCam2 is selected, the ‘selected IP address’ is displaye
ページ15に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 15 NetCam2 Section 2 1. Using ARP in Windows 98 and NT • Start a DOS window and type the following commands. arp -s ping -t • Example arp -s 200.243.232.178 00-40-8c-10-00-86 ping -t 200.243.232.178 2. Using ARP in Windows 95 • Start a DOS window and type the following commands. arp -s ping
ページ16に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 16 NetCam2 Section 2 • If you succeed in utilizing the above commands, you will receive a continuous connection. Stop the process by pressing + keys. • If the statistic shows ‘100% loss’, you should check that the network line and connection status are stable; the IP address which is assigned to NetCam2; and whether a PC has the same local IP address as the NetCam2. (Same local IP address of C grade network means that the first 3 numbers
ページ17に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 17 NetCam2 Section 3 3. OPERATION This section looks at accessing the NetCam2’s homepage and monitoring real- time images. The NetCam2’s own web pages are accessed through one of the recommended Web browsers. 3.1 Starting Web browser • Start the browser and enter the NetCam2 IP address: http:/// • Example – http://200.243.232.178/ Note: NetCam2 simultaneously supports up to 100 users. Additional users will receive the message
ページ18に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 18 NetCam2 Section 3 Note: Program installation takes less than 1 minute. Do not click any button until the ‘Active-X Control’ installation is completed. 3.3 Various viewers in NetCam2 homepage 3.3.1Login and homepage On the NetCam2 Login Page: • Enter your user name and password to log in (max 9 characters). • Click on 'Login' to connect the default viewer page (as set by the administrator) or click on one of the viewer links (see 'Home page' fo
ページ19に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 19 NetCam2 Section 3 Homepage On the NetCam2 Homepage there are four viewing options. Users may monitor real-time images via these main viewers. The four viewers are: • Lite viewer: for real-time monitoring with simplified viewer with limited camera and image control (faster page download). • Full viewer: for real-time monitoring with full camera and image control. • Server-Push viewer: for real-time monitoring from behind a fire wall. • Java Appl
ページ20に含まれる内容の要旨
NetCam2 _ii_00592en.qxd 1/23/03 2:22 PM Page 20 NetCam2 Section 3 The homepage displays one image. The following can be selected using pull- down menus: • Select View – camera 1, 2 or all cameras. • Resolution – set image resolution to 720x486, 720x243, 360x243, 180x121 or 90x60. • Expansion – expand image 1x, 2x or 4x. • Frame rate – set frame rate. 3.3.2 Real-time monitoring through Full viewer (single view) • From the home page, click on ‘Full Viewer’. • The default view is shown. 20
