ページ1に含まれる内容の要旨
Network Camera User’s Guide
Infra-Red
Network Camera
User’s Guide
Software Version 2.1.7
1/83
ページ2に含まれる内容の要旨
Network Camera User’s Guide PT IP Cam / IR IP Cam / Video Server Series © 2005. Owner's Record The model and serial numbers are located at the bottom. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. ______________ Serial No. ____________________ To prevent fire or shock hazard, do not expose the unit to rain or moisture. For AC Adaptor to avoid electrical shock, do not open the cabinet.
ページ3に含まれる内容の要旨
Network Camera User’s Guide Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE TO USERS © 2005. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated or r
ページ4に含まれる内容の要旨
Network Camera User’s Guide Table of Contents Overview ............................................................................................................................. 6 Package Contents................................................................................................................ 8 Connections......................................................................................................................... 9 Hardware Installation.......................
ページ5に含まれる内容の要旨
Network Camera User’s Guide Popup............................................................................................ 45 Firmware upgrade:........................................................................ 46 Factory Default............................................................................. 49 Reboot........................................................................................... 50 Trigger.....................................................................
ページ6に含まれる内容の要旨
Network Camera User’s Guide Overview This user’s guide explains how to operate the Infra-Red (IR) Network Camera from a computer. Basically, the user’s guide is written to be read on the computer display. However, users might consider printing it out to access easily and read it before you operate the Network Camera. Introduction This IR Network Camera is an inexpensive fully scalable surveillance technology. Because the Network Cameras can be plugged in to your existing computer ne
ページ7に含まれる内容の要旨
Network Camera User’s Guide Application: Remote monitoring Surveillance Minimum System Requirement Microsoft Internet Explorer 5.0 or later VGA Monitor resolution 1024 x 768 Pentium 4 1.3GHz or above Memory Size: 256MB or above Windows ME, 2000, XP, or 2003 7/83
ページ8に含まれる内容の要旨
Network Camera User’s Guide Package Contents User can find the following items in the package: Infra-Red IP Camera x 1 Wall mount x 1 RS-485 terminal x 1 Installation software and manual CD x 1 Quick installation guide If any of the above items are missing, please contact your dealer immediately. 8/83
ページ9に含まれる内容の要旨
Network Camera User’s Guide Connections Rear Panel Connections: 1. RS-485: To connect to an indoor/outdoor Pan/Tilt scanner unit. Definition of the RS-485: Orange: D- Blue: D+ 2. LAN port: To connect to PC or Hub. The LAN socket is an RJ-45 connector for connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built NWay protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 “straight thr
ページ10に含まれる内容の要旨
Network Camera User’s Guide 3. AC power cord & Local Video out (BNC port) The AC power input and video output cable are located on the Network Camera’s back panel. The input power is 85~260VAC.. The Network Camera also provides composite video output. User can use BNC video cable to connect the Network Camera with a TV monitor or VCR. 10/83
ページ11に含まれる内容の要旨
Network Camera User’s Guide Hardware Installation 1. Fix IR camera to desired location with wall mount fixture 2. Plug-in Network Cable into Ethernet port Connect an Ethernet cable to the LAN socket located on the Network Camera’s back panel and attach it to the network. 3. Connect RS485 two wires to RS485 D+ and D- ( if you need to control PT scanner) 4. Plug-in Power cable into power socket 5. Connect Video BNC connector to a local TV (for checking camera viewing angle)
ページ12に含まれる内容の要旨
Network Camera User’s Guide Logging in to Homepage Before Operation Install the IP Address of Network Camera When you installed your Network camera on your LAN environment, you may execute IPFINDER.EXE to discover Network camera’s IP address. IPCam Finder program (IPFINDER.EXE) is used to scan the Installed Network Camera, setting the Network Camera Name, IP address settings and so on. Using your mouse to select any one of the Network Cameras within your LAN 12/83
ページ13に含まれる内容の要旨
Network Camera User’s Guide environment, you can find out its IP address and other IP parameters as follows: 1. Edit the Name of this Network Camera. Note that use “_” or “-“ to replace “space” character to separate the name string. For example, “Dome_IP” or “Dome-IP” will be right. However “Dome IP” will not work here. 2. Might be needed to update the IP address of this Network Camera. ( Power recycling i might be necessary) 3. Might be needed to update the Gateway Address. ( Power rec
ページ14に含まれる内容の要旨
Network Camera User’s Guide First time uses the Network Camera The Network Camera web page communicates with the Network Camera using an ActiveX control. The ActiveX control must be downloaded from the Network Camera and installed on your PC. Your Internet Explorer security settings must allow for the web page to work correctly. To use the Network Camera, user must setup his IE browser as follows: From your IE browse ”Tools” ”Internet Options…” ”Security” ”Custom Level…”,
ページ15に含まれる内容の要旨
Network Camera User’s Guide By now, you have finished your entire PC configuration for Network Camera. 15/83
ページ16に含まれる内容の要旨
Network Camera User’s Guide Access the Network Camera from the Internet Explorer for the first time 1. Start the web browser on the computer and type the IP address of the Network Camera you want to monitor as below: The Login Window of the Network Camera is displayed: 2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the first time use (default value), input the User Name : admin Password: 16/83
ページ17に含まれる内容の要旨
Network Camera User’s Guide That’s, type in “admin” on the “USERNAME” as a default name and leave PASSWORD textbox blank. Click “OK” button to start the main menu. Now, you login to the Network Camera as a full-authorized administrator. You can enter “Setting” to change the password and setup “Administrator” or “User” authority. Please refer to “Setting” “User” and “IP Filter”. 3. The IE Web Page will display the “Security Warning” window, select “Yes” to install and run the A
ページ18に含まれる内容の要旨
Network Camera User’s Guide Logging in as an ordinary User For ordinary user usage, “Setting”, “Trigger”, and “Capture” will be not available. On the right side of the screen, there are lots of controls and function buttons. If “Remote camera control” is turned off by the administrator, then those control and function buttons will not be available as well. For the rest of this user guide, it is assumed that the “Remote camera control” will be turned on for normal operation.
ページ19に含まれる内容の要旨
Network Camera User’s Guide Operating the Network Camera Start-up screen will be as follow no matter an ordinary users or an administrator. Viewing Area: Images from the Network Camera 19/83
ページ20に含まれる内容の要旨
Network Camera User’s Guide Control Panel Control Panel Area: Network Camera Manipulation and image quality control Item Button Meaning 1 Camera Control camera up/down/left/right and home position direction Note: It’s useful if IR Network Camera is carried by a P/T scanner. Otherwise, this function is not available. 2 Camera Adjust camera speed up / down speed Note: It’s useful if IR Network Camera is carried by a P/T scanner. Otherwise, this function is not availab
