ページ1に含まれる内容の要旨
Quick Setup Guide
Start Here MFC-5890CN
Before you can use the machine, read this Quick Setup Guide for the correct setup and installation.
Warnings tell you what to do to prevent possible personal injury.
WARNING
Important
DO NOT connect the USB cable yet (if you are using a USB
cable).
Unpack the machine and check the components
1
Black (LC65HY-BK)
Yellow (LC65HY-Y)
Cyan (LC65HY-C)
Magenta (LC65HY-M)
Ink Cartridges [x4]
User’s Guide CD-ROM Accessory Order Form
Quick Setup Guide
Test Sheet (US
ページ2に含まれる内容の要旨
c With both hands, gently press and slide the paper side guides a and then the paper length Load plain Letter/A4 guide b to fit the paper size. paper 2 Make sure that the triangular marksc on the paper side guides a and paper length guide b a Pull the paper traya completely out of the line up with the mark for the paper size you are machine. using. 1 1 3 Note When you use Legal, A3 or Ledger size paper, press and hold the universal guide release buttona as you slide out the front of the
ページ3に含まれる内容の要旨
g Close the paper tray cover. Check that the paper is flat in the tray and below the maximum paper marka. 1 h Slowly push the paper tray completely into the machine. i While holding the paper tray in place, pull out the paper supporta until it clicks, and then unfold the paper support flapb. 2 2 1 1 3
ページ4に含まれる内容の要旨
Note Connect the power cord If you are sharing one telephone line with an and telephone line 3 external telephone, connect it as shown below. Before you connect the external telephone, remove the protective cap a from the EXT. jack Important on the machine. DO NOT connect the USB cable yet (if you are using a USB cable). 11 a Connect the power cord. 22 1 b Connect the telephone line cord. Connect one end of the telephone line cord to the jack on the 1 Extension telephone machine marked LI
ページ5に含まれる内容の要旨
e Turn the green knob on the protective yellow cap clockwise until it clicks to release the Install the ink cartridges vacuum seal, then remove the capa. 4 WARNING If ink gets in your eyes, wash them out with water at once, and if irritation occurs consult a doctor. a Make sure that the power is turned on. The LCD shows: No Cartridge Install Ink 1 Black b Open the ink cartridge covera. f Take care to match the color of the levera with the cartridge colorb, as shown in the diagram below. 1
ページ6に含まれる内容の要旨
h Gently push the ink cartridge until it clicks. After Important all the ink cartridges are installed close the ink cartridge cover. • DO NOT take out ink cartridges if you do not need to replace them. If you do so, it may reduce the ink quantity and the machine will not know the quantity of ink left in the cartridge. • DO NOT shake the ink cartridges. If ink stains your skin or clothing, wash with soap or detergent at once. • DO NOT repeatedly insert and remove the cartridges. If you d
ページ7に含まれる内容の要旨
d The LCD asks you if the print quality is OK for black and color. Press 1 (Yes) or 2 (No) on the Check the print quality dial pad. 5 Black OK? a When the preparation process has finished, the LCD shows this message . Yes Press No Press Set Paper and Press Start After pressing 1 (Yes) or 2 (No) for both black and color, the LCD shows: Start Cleaning? Press Color Start. Yes Press b Check the quality of the four color blocks a on No Press the sheet. (black/yellow/cyan/magenta) e Press 1 (Yes
ページ8に含まれる内容の要旨
Choose the correct Receive Mode 7 The correct Receive Mode is determined by the external devices and telephone subscriber services (Voice Mail, Distinctive Ring, etc.) you have (or will be using) on the same line as the Brother machine. Will you be using a Distinctive Ring number for receiving faxes? Brother uses the term "Distinctive Ring" but telephone companies may have other names for this service such as Custom Ringing, RingMaster, Personalized Ring, Teen Ring, Ident-A-Call, and Smart Rin
ページ9に含まれる内容の要旨
d Enter the last two digits of the year on the dial pad, and then press OK. Set the LCD contrast Date&Time (If needed) 8 Year:20 08 If you are having difficulty reading the LCD, try changing the contrast setting. MENU Input & Press OK a Press Menu. (e.g. Enter 0 8 for 2008.) b Press a or b to choose General Setup. Press OK. e Enter the two digits for the month on the dial pad, and then press OK. c Press a or b to choose LCD Settings. Date&Time Press OK. Month: d Press a or b to choos
ページ10に含まれる内容の要旨
f Press Stop/Exit. Set your station ID Note 10 If you make a mistake and want to start again, press Stop/Exit and go back to a. You should store your name and fax number to be printed on all fax pages that you send. For details, see Entering Text in Appendix C of the User's Guide. a Press Menu. b Press a or b to choose Initial Setup. Note Press OK. (USA only) c Press a or b to choose Station ID. The Telephone Consumer Protection Act of 1991 Press OK. makes it unlawful for any person to use a
ページ11に含まれる内容の要旨
Set tone or pulse dialing Automatic Daylight mode Savings Time 11 12 Your machine comes set for Tone dialing service. If You can set the machine to change automatically for you have Pulse dialing service (rotary), you need to daylight savings time. It will reset itself forward one change the dialing mode. hour in the Spring and backward one hour in the Fall. a Press Menu. a Press Menu. b Press a or b to choose Initial Setup. b Press a or b to choose General Setup. Press OK. Press OK. c Pre
ページ12に含まれる内容の要旨
e Press Black Start. Send in the Product Registration and Test Note 13 Sheet (USA only) You will receive a confirmation fax of your Product Registration. You can also register your product online using the On-Line Registration link from the installation CD-ROM or visit http://www.brother.com/registration/. a Fill out the Product Registration and Test Sheet. b Put the sheet face up in the ADF (Automatic Document Feeder) or face down on the scanner glass. c Make sure (Fax) is illum
ページ13に含まれる内容の要旨
® ® ® ® Windows Macintosh Windows Macintosh USB Wired Network Choose your connection type 14 For USB interface cable ® Windows , go to page 14 ® Macintosh , go to page 18 For Wired Network ® Windows , go to page 21 ® Macintosh , go to page 26 13
ページ14に含まれる内容の要旨
® USB Windows For USB Interface Users ® (For Windows 2000 Professional/XP/ XP Professional x64 Edition/ ® Windows Vista ) Before you install Install MFL-Pro Suite 15 16 a Make sure that your computer is ON and you a Put the supplied CD-ROM into your CD-ROM are logged on with Administrator rights. drive. If the model name screen appears, choose your machine. If the language screen Important appears, choose your language. • DO NOT connect the USB cable yet. • If there are any programs running,
ページ15に含まれる内容の要旨
® ® Windows Macintosh USB ® USB Windows g Choose Local Connection, and then click Note Next. The installation continues. • If this screen appears, click OK and restart your computer. • If the installation does not continue automatically, open the main menu again by ejecting and then reinserting the CD-ROM or double-click the start.exe program from the h When this screen appears, go to the next step. root folder, and continue from b to install MFL- Pro Suite. ® • For Windows Vista , when th
ページ16に含まれる内容の要旨
® USB Windows c Carefully route the USB cable through the trench and out the back of the machine as Connect the USB cable shown below and connect the cable to your 17 computer. Important • DO NOT connect the machine to a USB port on a keyboard or a non-powered USB hub. • Connect the machine directly to your computer. a Lift the scanner cover until it locks securely into the open position. Important Make sure that the cable does not restrict the cover from closing, or an error may occur.
ページ17に含まれる内容の要旨
® ® Windows Macintosh USB ® USB Windows Connect the power cord Finish and restart 18 19 a Connect the power cord. a Click Finish to restart your computer. The installation will continue automatically. After restarting the computer, you must be logged on with Administrator rights. The installation screens appear one after another. Note If an error message appears during the software installation, run the Installation Diagnostics Important located in Start/All Programs/Brother/ MFC-XXXX (wher
ページ18に含まれる内容の要旨
® USB Macintosh ® For USB Interface Users (For Mac OS X 10.2.4 or greater) b Connect the USB cable to the USB socket marked with a symbol. You will find the Before you install USB socket inside the machine on the right as 15 shown below. a Make sure your machine is connected to the ® power and your Macintosh is ON. You must LAN USB be logged on with Administrator rights. Important ® • For Mac OS X 10.2.0 to 10.2.3 users, ® upgrade to Mac OS X 10.2.4 or greater. (For ® the latest informat
ページ19に含まれる内容の要旨
® ® Windows Macintosh USB ® USB Macintosh d Lift the scanner cover to release the locka. c The Brother software will search for the Brother Gently push the scanner cover support device. During this time the following screen downb and close the scanner coverc using will appear. both hands. 1 d When this screen appears, click OK. 3 2 ® For Mac OS X 10.3.x or greater, the installation of MFL-Pro Suite is now complete. Go to step 18 on page 20. ® e For Mac OS X 10.2.4 to 10.2.8 users, Install
ページ20に含まれる内容の要旨
® USB Macintosh h Click Print Center, then Quit Print Center. Install ® ® 18 Presto! PageManager ® ® When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2. You can easily scan, share and organize photos and ® ® documents using Presto! PageManager . a Double-click the Presto! PageManager icon and follow the on-screen instructions. The installation of MFL-Pro Suite is now complete. Go to step 18 on page 20. ® For Mac OS X 10.2.4 to 10.3.8 users, when this
