ページ1に含まれる内容の要旨
COLOUR VIDEO CAMERA
INSTRUCTIONS
TK-C1430
LWT0207-001B-H
E-1
TK-C1430/01-05,E.65E 1 9/13/04, 2:53 PM
DIGITAL
COLOR VIDEO CAMERA
BF LOOK
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 6. Do not use this appliance near water - for example, near a batht
ページ3に含まれる内容の要旨
13. Follow all warnings and instructions marked on the appliance. 14. Do not overload wall outlets and extension cords as this can result in fire or electric shock. 15.Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. 16.Do not attempt to service this appliance yourself as opening or removing covers may expose you to
ページ4に含まれる内容の要旨
Safety Precautions Due to design modifications, data given in this instruction book are subject to possible change without prior notice. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVERTISSEMENT: POUR EVITER LES RISQUES D’INCENDIE OU D’ELECTRO- CUTION, NE PAS EXPOSER L’APPAREIL A L’HUMIDITE OU A LA PLUIE. E-4 TK-C1430/01-05,E.65E 4 9/13/04, 2:53 PM
ページ5に含まれる内容の要旨
Thank you for purchasing this product. (These instructions are for TK-C1430E) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. CONTENTS INTRODUCTION Features ...............................................................................................................................6 Operating Precautions ......................................................................................
ページ6に含まれる内容の要旨
INTRODUCTION Features A DSP (Digital Signal Processor) features Before starting an important recording, a Extended Dynamic Range (ExDR) and be sure to perform a test recording in enables to shoot both bright and dark order to confirm that a normal locations. recording is possible. We do not accept liability for the loss of The use of a CCD with a SENSE UP (X32) a recording in the case of it becoming function realized the minimum luminous impossible to record due to a problem flux density
ページ7に含まれる内容の要旨
Operating Precautions ● To save energy, when it is not being used ● Observe the following when carrying out turn the system’s power off. camera maintenance. ● This camera has been designed for indoor •Turn the power OFF before proceeding use. When you use it outdoors, be sure to carry out maintenance. to use a housing or the like. If it is contaminated seriously, clean the ● Do not install or use the camera in the contaminated part with a cloth (or a following places. tissue) which has been soak
ページ8に含まれる内容の要旨
INTRODUCTION Controls, Connectors and Indicators Lens mount Camera-mounting bracket 1 4 To attach the lens. The bracket has been attached on the This is applicable to both C-mount lenses bottom of the camera before shipment. It and CS-mount lenses. can also be attached on the top according to the circumstance. Back focus adjustment ring 2 To re-attach the bracket use the threaded Adjusting the back focus during lens holes at the top, with the camera installation. mounting bracket fixing screws .
ページ9に含まれる内容の要旨
SET CAMERA SETUP ON AWC EXT TERM-OFF MENU INT/GL LL SIMPLEX DUPLEX RX TERM-OFF ON NOT USED IRIS VIDEO DC Cover [SET/AWC] Set. Auto White Control 8 12 The cover slides open when push to the Button left. SET: Press this button to display a sub- menu. [VIDEO/DC] Iris Selector Switch 9 ( Page 23) This should be set according to the type AWC: If this button is kept pressed for of lens if an automatic iris control lens is more than 1 second, a one-push- used. auto-white-balance function works VIDEO
ページ10に含まれる内容の要旨
INTRODUCTION Controls, Connectors and Indicators (Continued) [ , , , ] Up-and-down, left-and- SIMPLEX: 13 right Button This switch sets to SIMPLEX when the These buttons select items on the menu transmission between the camera and a screen and change a set value. remote control unit is in a simplex system ( Page 23) (one-way). (DUPLEX: At time of factory shipment) [EXT.TERM-ON/OFF] Terminal On/Off 14 Switch of External Synchronization [RX.TERM-ON/OFF] RX Signal Terminal 17 Signal ON/OFF Switch
ページ11に含まれる内容の要旨
( ) ⁄ + - 12 TX+ TX- RX+ RX- AUX GND A B CD Y/C OUT fi ¤ SYNC IN VIDEO OUT SEE INST- RUCTION MANUAL POWER › ‹ [DC 12V, AC 24V] Power input terminals 4 19 3 To input DC 12V or AC 24V power. 2 1 [TX+A, TX-B, RX+C, RX-D] Control 20 Pin No. Signal signal connection terminals Terminals for inputting signals with 1 GND electrical characteristics conforming to 2 GND the EIA/TIA RS-422A or RS-485 standard. 3 Luminance (Y) 4 Chrominance (C) RX.TERM switch 17 [AUX, GND] Auxiliary Input/Output 21 [VIDEO
ページ12に含まれる内容の要旨
CONNECTION/INSTALLATION RM-P2580 System System with up to 8 cameras Camera TK-C1430 Control signal cable Video signal cable Camera 1 AC24V Power MACHINE ID:1 or (Menu screen) cable DC12V RX TERM: OFF Camera (switch) TK-C1430 Camera 2 AC24V MACHINE ID:2 or (Menu screen) DC12V RX TERM: OFF (switch) Camera TK-C1430 MONITOR Camera 8 AC24V •• • • • Time lapse VCR CAM SW MACHINE ID:8 or SR-L910 REC STOP/EJECT REC OUT CHECK VIDEO CASSETTE RECORDER OPERATE (Menu screen) PAUSE/ OPE. LOCK REVERSE STILL
ページ13に含まれる内容の要旨
Connecting the control signal cable (Use a twisted-pair cable for connection. Page 17.) Camera 1 control signal connection terminals RM-P2580 Connect: TX+ A A RX + Camera TX+ to RM-P2580 RX+ B RX TX B Camera TX– to RM-P2580 RX– RX+ C C TX + Camera RX+ to RM-P2580 TX+ RX D D TX Camera RX– to RM-P2580 TX– Camera 2 The A B C D marks indicated on both the control signal camera terminals and the RM-P2580 termi- connection terminals nals facilitate correct connections. Connect TX+ A the ter
ページ14に含まれる内容の要旨
Av Pk L H LEVEL ALC CONNECTION/INSTALLATION Procedures Execute connection/installation according to the procedures described below. Turn OFF the power supply to all equipment to be used before making carefully. 4.Setting the switches 6.Back focus adjustment ( Page 13) ( Page 21) SET CAMERA SETUP EXT TERM-OFF ON MENU INT/GL LL DUPLEX SIMPLEX RX TERM-OFF ON IOT USED VIDEO DC 5.Lens adjustment 7.Auto white balance ( Page 20) control adjustment ( Page 22) 1.Mounting the lens 3.Mounting
ページ15に含まれる内容の要旨
Mounting the lens Mount the lens according to the procedures described below. 1. Before mounting a lens, check whether it is a C-mount or CS-mount lens. To change the mounting method, loosen the back-focus locking screw (M 2.6) using a Phillips head screwdriver, turn the back-focus adjusting ring with your fingers or the screwdriver and change the mounting method. As regards the dimension (b) of the area to which the lens is to be installed as illustrated on the left diagram, use the one with le
ページ16に含まれる内容の要旨
Av Pk L H ALC LEVEL CONNECTION/INSTALLATION Installing the ferrite core To retain electromagnetic compatibility, use the ferrite cores provided when connecting to the lens. Video-iris lens (or galvanometnc-iris lens) Wind once IRIS VIDEO DC Ferrite core Wire clamp Notes: • Install the ferrite cores within 50 mm of the camera-side connectors. (Fasten the ferrite core with the wire clamp provided.) • If the LENS cable is short, please connect the cable to the camera without winding the cabl
ページ17に含まれる内容の要旨
MEMO • If thin cables are used (i.e. with a high resistance), a significant voltage drop will occur when the unit is at its maximum power consumption. Either use a thick cable to restrict the voltage drop at the camera side to below 10%, or place the power supply near to the camera. If voltage drop occurs during operation, the performance will be unstable. • Attach the cable conductors so that they do not come into contact with the drop prevention wires. • Do not allow input from both a DC 12 V
ページ18に含まれる内容の要旨
CONNECTION/INSTALLATION Mounting the camera When mounting the camera on a fixer, pan/ tilt, etc., use the camera mounting screw hole Camera mounting located on the camera-mounting bracket. screw hole Camera-mounting bracket CAUTION: Use the screw with a length shorter than 7mm from a camera-mounting face. MAX. 7mm Furthermore, make use of the rotation Rotation prevention hole prevention hole to prevent the camera from falling and securely mount the camera. Special precautions must be taken for m
ページ19に含まれる内容の要旨
Installation of camera q • Mounting from the bottom This camera is originally designed to be mounted from the bottom, as shown q. IRIS The hole is standard photographic pan- VIDEO DC head screw size (1/4-20 UNC). Example the Fixing unit or Pan/Tilt unit. • Mounting from the top Remove the CAMERA MOUNTING BRACKET from the bottom of the camera by removing two fixing screws as shown w. Attach the CAMERA MOUNTING BRACKET to the top, then mount the camera on the Fixing Unit as shown e. Make sure that
ページ20に含まれる内容の要旨
CONNECTION/INSTALLATION Lens adjustment Connect the camera according to the connection method, turn it on, display an image on the monitor, and check the image. The camera has been factory-adjusted to the best position, but it may need to be adjusted according to the object conditions or combination of lenses. If the image is unnatural, adjust it as follows: (Also read the instruction manual of the lens.) LEVEL adjustment • LEVEL adjustment Monitor screen LEVEL turning direction Too bright Count
