ページ1に含まれる内容の要旨
O OP PE ER RA AT TO OR R
M MA AN NU UA AL L
Initial issue: 02/03
Latest revision: 10/03
9.133702
ページ2に含まれる内容の要旨
This page is intentionally left blank. Operator Manual Initial issue: 02/03 Page 9 - 2 Latest revision: 10/03
ページ3に含まれる内容の要旨
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 DESCRIPTION OF THE PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . .6 DESCRIPTION OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . .7 1 - Features description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 - Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 JAM DETEC
ページ4に含まれる内容の要旨
This page is intentionally left blank. Operator Manual Initial issue: 02/03 Page 9 - 4 Latest revision: 10/03
ページ5に含まれる内容の要旨
INTRODUCTION This manual provides informations for operating the Xerox Interface Module. Welcome to the Xerox Interface Module. This product is an interface for the DocuTech 120 prin- ter. The XIM will enable in line finishing by receiving sheets from the host printer and sendinig these sheets in to a stacker or other Finishing device. The information contained in this manual is based on the most current information available at the time of editing. Operator Manual Initial issue: 02/03 Page 9 -
ページ6に含まれる内容の要旨
DESCRIPTION OF THE PROCESS Schematic view of the paper path. WITHOUT ROTATION WITH ROTATION Centered input -> Centered output Centered input -> Centered output Centered input -> Registred output Centered input -> Registred output Operator Manual Initial issue: 02/03 Page 9 - 6 Latest revision: 10/03
ページ7に含まれる内容の要旨
DESCRIPTION OF THE MACHINE 1 - Features description Top tray IN Led display Top cover OUT Front OUT Power cord The power supply Front door cord is used as the disconnect device. There is no Main switch. Docking plate to downstream device. Keyboard and switch for service use only. General: Height of the entrance / exit: 860mm / 33.8in. Height of the exit : 860 mm (33.8 in.) or 1020mm (40.1 in.) (Adjustable : + 60mm / 2.4in. and - 15mm / .6in.). Operator Manual Initial issue: 02/03 Page 9 - 7 Late
ページ8に含まれる内容の要旨
2 - Technical specifications Paper type: Min: 178 mm (7 in.) Max: 470 mm (18.5 in.) Min: 254 mm (10 in.) Paper processing Max: 364 mm (14.33 in.) direction Paper Size / Orientation Paper format: LEF SEF Inches mm Envelopes 4.12x9.5 to 105x241 to 2 #10 to 9"x12" X 9"x12" 229x305 A5 X (5.83x8.27) 148x210 Statement X 5.5x8.5 (140x216) 7x10 X 7x10 (178x254) B5 - JIS X (7.17x10.12) 182x257 Executive X 7.25x10.5 (184x267) 3 16K (Taiwan) X (7.64 x 10.51) 194x267 8x10 X 8x10 (203x254) 8x10 X 8x10 (203x2
ページ9に含まれる内容の要旨
Paper Size / Orientation PPM LEF SEF Inches mm 215x330 X (8.46x13) 215x330 72 Foolscap – XE X 8.5x13 (216x330) 72 220x330 X (8.66x13) 220x330 72 Legal X 8.5x14 (216x356) 72 9x14 X 9x14 (229x356) 72 SB4 X (9.9x14.1) 252x358 72 B4 –JIS X (10.12x14.33) 257x364 72 3 8K (Taiwan) X (10.51x15.28) 267x388 72 A3 X (11.69x16.54) 297x420 72 Ledger X (11x17) (279x432) 72 12x18 X 12x18 (305x457) 48 12x18.5 X 12x18.5 (305x470) 48 12.2x17 X (12.2x17) 310x432 48 4 up-6x9 X 12.5x18.5 (317.5x470) 48 2 up-6x9 X 12
ページ10に含まれる内容の要旨
JAM DETECTION The display represents the top tray and the paper path area. When part of the mimic is illuminated, there is a problem in this area. Top tray If the top tray area is illuminated, you have to open the top cover to check the area and clear the problem. Paper path If the paper path area is illuminated, you have to open the top cover to check the area and clear the problem. This window is blinking when the machine does a set-up, and ligh- ted when the machine is ready. Operator Manual
ページ11に含まれる内容の要旨
HOW TO PROGRAM A JOB (ROTATION OR REGISTRATION)? Refer to printer user interface, not available on XIM. Functions to be programmed: - Rotation/No rotation. - Centered or edge registered output. - Higher or lower exit selection... Operator Manual Initial issue: 02/03 Page 9 - 11 Latest revision: 10/03
ページ12に含まれる内容の要旨
JAM CLEARANCE - JOB RECOVERY - Location of the baffles 1 4 2 3 5 1 4 2 3 5 Operator Manual Initial issue: 02/03 Page 9 - 12 Latest revision: 10/03
ページ13に含まれる内容の要旨
TROUBLESHOOTING Problem Cause Solution Green power window not No power • Check that the power cord illuminated is connected to the wall outlet • Check if printer is ready • Check communication cable from Docutech 120 to XIM for proper connection • Check for other area if the mimic not illuminated • Check the service switch position (see "description Poor registration of the machine" chapter) High paper curl • Adjust printer decurler • Flip paper in printer paper tray Mecha
ページ14に含まれる内容の要旨
This page is intentionally left blank. Operator Manual Initial issue: 02/03 Page 9 - 14 Latest revision: 10/03
