ページ1に含まれる内容の要旨
Installation Instructions
Model CCDF
Color Camera External Mount
CCDF FEATURES:
High Resolution, 1/3”CCD Color Camera
Compact Zinc Alloy Die Cast Body
Waterproof Housing
Waterproof Microphone
Adjustable Mounting Angle
Wide Angle Lens
Flush Mount or Surface Mount
128-6951
1 of 12
ページ2に含まれる内容の要旨
Color Camera View: Cable Connector End View: 1 128-6951 2 of 12
ページ3に含まれる内容の要旨
Specifications: 1. Signal System: NTSC 2. Voltage: DC12V 3. Current: 80mA 4. Image Sensor: 1/3” CCD Color Sensor NTSC: 510 X 492 picture elements 5. Horizontal Definition: 420 Lines 6. Viewing Angle: 120 degrees 7. Minimum Illumination: 0.8 LUX 8. Outer Dimensions: 1.18”(W) x 1.10”(H) x 1.65”(D) 9. Weight: 2.5 Oz 2 128-6951 3 of 12
ページ4に含まれる内容の要旨
Contents: 3 128-6951 4 of 12
ページ5に含まれる内容の要旨
Contents Description: 1. Camera: 1 8. Slant Washer 1: 1 2. Support Bracket: 1 9. Slant Washer 2: 1 3. Lock Nut: 1 10. Tapping Screw: 2 4. Protective Cover: 1 11. Combine Screw: 2 5. Top Cover: 1 12. Washer: 2 6. Flat Washer 1: 1 13. Docking Nut: 2 7. Flat Washer 2: 1 4 128-6951 5 of 12
ページ6に含まれる内容の要旨
Flush Mount Note: 1. Camera 3. Lock Nut 5. Top Cover 6. Flat Washer 1 14. Mounting Plate 5 128-6951 6 of 12
ページ7に含まれる内容の要旨
Flush Mount Installation: 1. Select a suitable mounting location in the rear center of vehicle. Check behind panel for wire routing access and confirm that the drill will not damage any existing components. Use a 7/8” hole saw to drill the mount ing hole. 2. Screw the lock nut with the threaded side toward the camera body in the showed direction, then put the camera neck through the mounting hole with the lens exposed and wire cable facing down. 3. Place the flat washer 1 (# 6) and top cover (#
ページ8に含まれる内容の要旨
Angle Flush Mount Size of Mounting Holes (See the Attached Page) Note: 1. Camera 3. Lock Nut 5. Top Cover 7. Flat Washer 2 8. Slant Washer 1 9. Slant Washer 2 7 128-6951 8 of 12
ページ9に含まれる内容の要旨
Angle Flush Mount Installation: 1. Select a suitable mounting location in the rear center of vehicle. Check behind panel for wire routing access and confirm that the drill will not damage any existing components. Drill four 1/8” positioning holes and one 7/8” mounting hole at the mounting location according to the drawing of Size of Mounting Holes. 2. Screw the lock nut (# 3) and the flat washer 2 (# 7) with the non-threaded side to the camera neck in the showed direction. 3. Mount the slant was
ページ10に含まれる内容の要旨
Surface Mount Note: 1. Camera 2. Support Bracket 3. Lock Nut 4. Protective Cover 5. Top Cover 6. Flat Washer 1 11. Combine Screw 12. Washer 13. Docking Nut 9 128-6951 10 of 12
ページ11に含まれる内容の要旨
Surface Mount Installation: 1. Locate suitable mounting location in the rear center of the vehicle and use the support bracket (# 2) as a template to mark and drill two 5/32” holes on the mounting location. 2. Put the support bracket (# 2) onto the camera neck, then screw the lock nut along the camera neck to secure the bracket (# 2) to the camera body (# 1) in the showed direction. 3. Screw the combine screws (or tapping screws) into the holes to attach the camera support bracket to the vehicle
ページ12に含まれる内容の要旨
© 2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6951 128-6951 12 of 12
