ページ1に含まれる内容の要旨
Philips Consumer Electronics Manual 7629
Model no.: 27PS60S321
First Publish: 12740 T8
Technical Service Data
Rev. Date: 2002-06-06
Service and Quality
Print Date: 7/8/2004
Service Publications Dept.
One Philips Drive
P.O. Box 14810
Knoxville, TN 37914
Pg. SCHEMATIC DIAGRAMS AND PC BOARDS
17. Side AV and Headphone Panel (Diagram C)
1. PCB Locations
18. PIP Panel (Diagram P)
2. Power Supply (Diagram A1)
19. Main Panel (component side)
3. Line Deflection (Diagram A2)
20. Main Panel (copper si
ページ2に含まれる内容の要旨
Philips Consumer Electronics Manual 7629 Model no.: 27PS60S321 First Publish: 12740 T8 Technical Service Data Rev. Date: 2002-06-06 Service and Quality Print Date: 7/8/2004 Service Publications Dept. One Philips Drive P.O. Box 14810 Knoxville, TN 37914 Mechanical Diagrams REFER TO SAFETY GUIDELINES SAFETY NOTICE: ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT C
ページ3に含まれる内容の要旨
MAIN CABINET EXPLODED VIEW Page: 1 of 1
ページ4に含まれる内容の要旨
Philips Consumer Electronics Manual 7629 Model no.: 27PS60S321 First Publish: 12740 T8 Technical Service Data Rev. Date: 2002-06-06 Service and Quality Print Date: 7/8/2004 Service Publications Dept. One Philips Drive P.O. Box 14810 Knoxville, TN 37914 Electrical Adjustments REFER TO SAFETY GUIDELINES SAFETY NOTICE: ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMEN
ページ5に含まれる内容の要旨
Alignments Index of this chapter: 1. General Alignment Conditions 2. Commercial Models SDAM Entry 3. Hardware Alignments 4. Software Alignments and Settings Note: The Service Default Alignment Mode (SDAM) is described in the "Service Modes, Error Codes and Fault Finding" section. SDAM menu navigation is performed by using the MENU UP, MENU DOWN, MENU LEFT, and MENU RIGHT keys of the remote control transmitter. General Alignment Conditions Perform all electrical adjustments under the following co
ページ6に含まれる内容の要旨
VERSION 3.3 Microprocessor software version 3. To change the television’s mode, ensure the master setup remote control is in setup mode, then press the 0-2-4-9-9-5-MENU keys in order, without permitting the display to time out while entering the key sequence. Note: If the operational mode is changed, the television must be turned off and then back on to complete the mode change. When the television is in consumer mode, do not use the master setup remote control to activate commercial mode fe
ページ7に含まれる内容の要旨
SAVE V-CHIP ON / OFF V-CHIP SETUP > SLEEPTIMER OFF / 15 / 30 / 45 / 60 / 90 / 120 / 180 / 240 EXIT > 5. After making changes to the settings, the EXIT option may be used to leave the Institutional Television Menu. Hardware Alignments
ページ8に含まれる内容の要旨
Figure: Mono Carrier (Top View) LS Vg2 Adjustment 1. Enter SDAM: 2. Press the following key sequence on the remote control transmitter: 0-6-2-5-9-6-MENU Do not allow the display to time out between entries while keying the sequence. 3. Use the MENU UP/DOWN keys to highlight the WHITE TONE sub menu.
ページ9に含まれる内容の要旨
4. Press the MENU LEFT or MENU RIGHT key to enter the WHITE TONE sub menu. 5. In the WHITE TONE sub menu, press the MENU UP/DOWN keys to select NORMAL RED, NORMAL GREEN, or NORMAL BLUE. 6. Use the MENU LEFT/RIGHT keys to set the values of NORMAL RED, NORMAL GREEN and NORMAL BLUE to 40. 7. Press the MENU button twice to enter the normal user menu. 8. In the normal user menu, use the MENU UP/DOWN keys to highlight the PICTURE sub menu (if necessary). 9. Press the MENU LEFT/RIGHT keys to enter the
ページ10に含まれる内容の要旨
made in SDAM. Figure: V Cut-Off Table: Cut-off Voltage, Large Screen Screen Size Cut-off Voltage 25/28Tesla, 25/28BLD +140V +/- 4V 20RF/21RF/25RF/29RF,21RF Pin-Free, 25"HF LA, +145V +/- 4V 25V/27V/32V/35V/25"/33"/28BLS, 29",29SF EU, 21RF AP/CH, 25" AP/CH, 25RF/29RFAP/CH, 29SF AP +155V +/- 4V 21RF Ph, 24/28/32WS BLD,29RF (Eu), 28/32WSRF +160V +/- 4V Focusing 1. Connect the RF output of a video pattern generator to the antenna input. 2. Input a circle or crosshatch test pattern to the t
ページ11に含まれる内容の要旨
4. GEOMETRY 5. AUDIO Options Figure: Options Menu Options are used to control the presence or absence of certain features and hardware. How to change an Option Byte An Option Byte represents a number of different options. Changing these bytes directly makes it possible to set all options very quickly. All options are controlled via seven option bytes. To change Option Byte(s): 1. Enter SDAM: Press the following key sequence on the remote control transmitter: 0-6-2-5-9-6-MENU Do not
ページ12に含まれる内容の要旨
T8 Option Byte Codes MODEL OPTION BYTES OP1 OP2 OP3 OP4 OP5 OP6 OP7 20RF40 S321 * NOT AVAILABLE 20RF40 S325 * NOT AVAILABLE 20RF50 S321 0 23 129 162 252 152 0 20RF50 S325 0 23 129 162 252 152 0 21PT63 9A85 * NOT AVAILABLE 21PT83 9B85 * NOT AVAILABLE 25PS40 S321 0 23 1 1 144 153 0 25PS40 S325 0 23 1 1 144 153 0 25PS50 S321 0 23 1 162 252 152 0 26LL50 0131 16 23 1 1 144 153 0 26LW50 2231 16 23 1 162 252 152 0 27PS50 B321 0 23 1 162 252 152 0 27PS55 S321 0 23 1 162 252 152 0 27PS60 S321 0 23 1 1
ページ13に含まれる内容の要旨
SC3127 N321 213 18 2 64 0 - - SC3132 N321 223 222 43 40 0 - - SC3132 N331 223 222 43 40 0 - - * Option Byte Data for these models was not available at manual release. Refer to future updates to this manual regarding these models. Tuner Note: Described alignments are only necessary when the NVM (part reference number7602) is replaced. Figure: Tuner Menu IF PLL This adjustment is auto-aligned. Therefore, no action is required. AGC (AGC take over point) 1. Connect the RF output of a video p
ページ14に含まれる内容の要旨
10.Press the MENU button to return to the top level SDAM menu. 11.To ensure the AGC change takes effect: Turn the television set OFF by using the POWER button on the remote control transmitter or the local keyboard. Disconnect the television set from AC power for at least ten seconds. Reconnect the television set to AC power. Turn the television set ON by using the POWER button on the remote control transmitter or the local keyboard. SL (Slicing Level) This adjustment sets the sync slicing level
ページ15に含まれる内容の要旨
Figure: White Tone Menu The values of the black cut off level can be adjusted in the WHITE TONE sub menu. Normally, no alignment is needed for WHITETONE, and the given default values are used. Default settings: NORMAL (color temperature = 9600 K): NORMAL RED = 40 NORMAL GREEN = 40 NORMAL BLUE = 40 To adjust NORMAL RED, NORMAL GREEN, and NORMAL BLUE: 1. Enter SDAM: Press the following key sequence on the remote control transmitter: 0-6-2-5-9-6-MENU Do not allow the display to time out between ent
ページ16に含まれる内容の要旨
0-6-2-5-9-6-MENU Do not allow the display to time out between entries while keying the sequence. 6. Use the MENU UP/DOWN keys to highlight the GEOMETRY sub menu. 7. Press the MENU LEFT/RIGHT keys to enter the GEOMETRY sub menu. 8. Use the MENU UP/DOWN keys to highlight either the HORIZONTAL sub menu or the VERTICAL sub menu. 9. Press the MENU LEFT/RIGHT keys to enter either the HORIZONTAL sub menu or the VERTICAL sub menu. 10.Use the MENU UP/DOWN keys to select items in the HORIZONTAL sub menu o
ページ17に含まれる内容の要旨
Horizontal: Horizontal Parallelogram (HP) Aligns straight vertical lines at the top and the bottom of the screen; vertical rotation round the center. Horizontal Bow(HB) Aligns straight horizontal lines at the top and the bottom of the screen; horizontal rotation around the center. Horizontal Shift(HSH) Aligns the horizontal center of the picture to the horizontal center of the CRT. East West Width(EWW) Aligns the width of the picture. East West Parabola(EWP) Aligns straight vertical lines at
ページ18に含まれる内容の要旨
Vertical Shift(VSH) Aligns the vertical center of the picture to the vertical center of the CRT. After performing this alignment, it may be necessary to perform the VAM alignment again. Vertical Zoom(VX) Adjusts picture height. Service blanking(SBL) Turns the blanking of the lower half of the screen ON or OFF (to be used in combination with the vertical slope alignment). The table below lists the default GEOMETRY values for the different television sets. Table: Default Geometry Values Descriptio
ページ19に含まれる内容の要旨
Figure: Audio Menu No alignments are necessary for the AUDIO sub menu. Use the default values. AF-M Default value is 300. A2T TV A2 Threshold Default value is 250. To adjust AF-M: 1. Enter SDAM: Press the following key sequence on the remote control transmitter: 0-6-2-5-9-6-MENU Do not allow the display to time out between entries while keying the sequence. 2. Use the MENU UP/DOWN keys to highlight the AUDIO sub menu. 3. Press the MENU LEFT/RIGHT keys to enter the AUDIO sub menu. 4. Use the
ページ20に含まれる内容の要旨
4. Use the MENU UP/DOWN keys to select A2T. 5. Use the MENU LEFT/RIGHT keys to adjust the value of A2T to 250. 6. Press the MENU button to return to the top level SDAM menu. 7. To ensure the A2T setting is saved: Turn the television set OFF by using the POWER button on the remote control transmitter or the local keyboard. Disconnect the television set from AC power for at least ten seconds. Reconnect the television set to AC power. Turn the television set ON by using the POWER button on the remo
