ページ1に含まれる内容の要旨
MONITOR
INSTRUCTIONS
DT-V2000SU
For Customer Use:
Enter below the Serial No. which is located on the rear of
the cabinet. Retain this information for future reference.
A B C
PHASE CHROMA BRIGHT CONTRAST
ON
OFF
MENU SELECT INPUT SELECT
DT-V2000SU VOLUME/ENTER POWER
Model No. : DT-V2000SU
Serial No. :
1 00.12.20, 0:39 PM
ページ2に含まれる内容の要旨
Thank you for purchasing this JVC DTV monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. SAFETY PRECAUTIONS FCC INFORMATION WARNING : CAUTION: Changes or modification not approved by TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT JVC could void the user’s authority to operate EXPOSE THIS MONITOR TO RAIN OR MOISTURE. the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital devic
ページ3に含まれる内容の要旨
CONTENTS SAFETY PRECAUTIONS............................................................................................... 2 CONTROLS AND FEATURES ....................................................................................... 4 CONNECTIONS ............................................................................................................. 7 HOW TO HANDLE BASIC OPERATIONS..................................................................... 8 HOW TO PERFORM MAIN MENU ADJUSTMENTS.
ページ4に含まれる内容の要旨
CONTROLS AND FEATURES FRONT VIEW 2 3 4 1 AB C PHASE CHROMA BRIGHT CONTRAST ON OFF MENU VOLUME/ENTER SELECT INPUT SELECT DT-V2000SU POWER PHASE CHROMA BRIGHT CONTRAST AB C ON OFF DT-V2000SU MENU VOLUME/ENTER SELECT INPUT SELECT POWER 7 6 5 1 Speaker INPUT SELECT buttons 5 A built-in speaker is located in the right panel when the Select the video signal input to each terminal. monitor is viewed from the front. Input A button [INPUT A (RGB/COMPO.)] Selects the video signal input to
ページ5に含まれる内容の要旨
REAR VIEW 8 9 10 11 INPUT A INPUT B (RGB/COMPO.) (VIDEO) Y/C IN OUT IN OUT G/Y INPUT A INPUT B (RGB/COMPO.) (VIDEO) Y/C IN OUT IN OUT REMOTE IN/OUT G/Y INPUT C REMOTE IN/OUT INPUT C B/PB B/PB HD/ (RGB) HD/ /B-Y CS (RGB) AC INPUT AUDIO INPUT /B-Y CS R/PR VD /R-Y AC INPUT EXT SYNC (MONO) AUDIO INPUT R/PR VD /R-Y EXT SYNC (MONO) 14 12 13 15 AC outlet (120 V AC, 60 Hz) 8 INPUT A (RGB/COMPO.) terminals 10 INPUT C (RGB) terminal Input (IN) and output (OUT) terminals for Analog R
ページ6に含まれる内容の要旨
CONTROLS AND FEATURES (cont’d.) Notes: 11 REMOTE IN/OUT terminal External control input and output terminal. Instead of ● To test external control, short-circuit the REMOTE using the INPUT SELECT button, an external control ENABLE terminal (Pin No. 1) to the GND terminal (Pin signal changes the INPUT mode. INPUT mode status No. 8) so that the external remote control becomes valid data is also output through this terminal. (L level). External control doesn’t function when external * The terminal
ページ7に含まれる内容の要旨
CONNECTIONS Notes: ● Before connecting your system, make sure that all units are turned off. ● The illustration below shows some examples of different connections. Terminal connections may differ depending on the component(s) connected. Be sure to refer to the instructions provided with the unit(s) you are connecting. BASIC CONNECTION EXAMPLE 0 ! Bridge output of 9 Unit outputting Y/C (S-video) signal 9 Unit outputting video signal [Rear-panel terminals] 1 Unit outputting analog INPUT A INPUT
ページ8に含まれる内容の要旨
HOW TO HANDLE BASIC OPERATIONS BASIC OPERATION ON OFF 1. Press the POWER switch to Selected Input Display (Mode) POWER turn on the power. Display Input ON (_): Power turns ON. (Power indicator lights in INPUT A (RGB) RGB input green.) INPUT A (COMPO.) COMPONENT input OFF (—): Power turns OFF. (Power indicator goes out.) INPUT B (VIDEO) VIDEO input * The frequency of the input INPUT B (Y/C) Y/C input Input display signals (or the color system or INPUT C RGB (PC) input DTV format) is automatica
ページ9に含まれる内容の要旨
OPERATION OF PICTURE ADJUSTMENT KNOBS PHASE knob Notes: Adjusts picture hue. ● The standard position of each knob is the center point PHASE where the knob clicks into place. reddish greenish The standard position is also indicated in the menu. ● Adjusting the PHASE knob and CHROMA knob may have CHROMA knob no effect depending on the input signal (input mode). Adjusts picture chroma. ( : valid – : invalid) CHROMA INPUT SELECT switch lighter deeper Picture AB C adjust- ment RG
ページ10に含まれる内容の要旨
HOW TO PERFORM MAIN MENU ADJUSTMENTS • H SIZE: adjusts the horizontal screen size • H POSITION: adjusts the horizontal screen position ADJUSTMENT OF SCREEN SIZE • V SIZE: adjusts the vertical screen size AND SCREEN POSITION • V POSITION: adjusts the vertical screen position You can adjust the screen size and screen position. SELECTING [ sub menu] IN PROCEDURE 4 This function can be set when an INPUT A component (COMPO.) You can also adjust items in procedure 5 with only the signal or INPUT B (
ページ11に含まれる内容の要旨
• PINCUSHION: adjusts the pincushion distortion • PIN. BALANCE: adjusts the balance of the pincushion distortion PICTURE DISTORTION • PARALLELOGRAM: adjusts the parallelogram distortion ADJUSTMENT • TRAPEZOID: adjusts the trapezoid distortion You can adjust the picture distortion. SELECTING [ sub menu] IN PROCEDURE 4 This function can be set when an INPUT A component (COMPO.) signal or INPUT B (VIDEO) signal is input with the underscan size You can also adjust items in procedure 5 with only th
ページ12に含まれる内容の要旨
HOW TO PERFORM MAIN MENU ADJUSTMENTS (cont’d.) PICTURE ADJUSTMENT You can adjust the picture contrast, brightness, etc. SELECTING [ sub menu] IN PROCEDURE 4 You can also adjust items in procedure 5 with only the 1 Press the MENU button. selected item displayed. Use this if the full menu screen MENU makes it difficult to observe the monitor image. The screen appears. 1Select the [ sub menu] item in procedure 4. 2Press the VOLUME/ ENTER button. screen The
ページ13に含まれる内容の要旨
p p • RGB/COMPO. : sets the input signal of the INPUT A terminal • SCAN SIZE : sets the scan size FUNCTION SELECTION (SETTING) • ASPECT : sets the aspect ratio • COLOR SW : sets the color switch You can select (set) the display’s functions. • COLOR TEMP.: sets the color temperature 1 Press the MENU button. MENU RESETTING ITEMS TO THEIR FACTORY-SET (INITIAL) The screen appears. VALUES You can reset each item (RGB/COMPO., SCAN SIZE, ASPECT COLOR SW and COLOR TEMP.) in the
ページ14に含まれる内容の要旨
HOW TO PERFORM MAIN MENU ADJUSTMENTS (cont’d.) Connection Between Input Mode Display and DISPLAY OF PRESENT INPUT Frequency (or Color System or DTV Format) Display STATUS Input Input Frequency, Input Mode Frequency, Mode Signal Color System or Display Color You can see the present status of the input mode and frequency DTV Format System or (or color system or DTV format). The status display disappears Signal DTV Format after three seconds. Display This function is available with all input sign
ページ15に含まれる内容の要旨
Recommended Input Mode List DEGAUSSING THE SCREEN Mode Resolution Horizontal Vertical Preset Frequency Frequency If the monitor is placed too close to a speaker or other device Horizontal Vertical (kHz) (Hz) incorporating a magnet, or if it is moved with the power on, NTSC 786 243 15.73 29.97 (i) irregular color may appear on the screen. If this happens, activate the degaussing circuit to degauss the picture. This 480i 720 244 15.73 29.97 (i) circuit will remove the irregular color from th
ページ16に含まれる内容の要旨
HOW TO PERFORM SET-UP MENU ADJUSTMENTS POWER SAVE FUNCTION POWER SAVE FUNCTION SETTING How the Power Save Function Operates This monitor has a power save function. For example, if the ●Horizontal synchronization signal vanishes. power is turned on with no signal input or the signal input is no ≠ longer detected, the power save function puts the monitor into The “NO SYNC” indication is displayed and about 10 signal-waiting mode (the screen goes out). seconds later the “POWER SAVE” indication is
ページ17に含まれる内容の要旨
CONTROL LOCK OF BUTTONS SETTING DISPLAY OF PRESENT AND KNOBS INPUT STATUS WHEN INPUT IS TURNED ON/OFF You can set the CONTROL LOCK function to disable control buttons and knobs on the front panel, except for the power switch. This function (STATUS DISPLAY) is set in the screen. This function is set in the screen. 1 While pressing the 1 While pressing the SELECT button, press SELECT button, press SELECT SELECT the VOLUME/ENTER the VOLUME/ENTER button.
ページ18に含まれる内容の要旨
HOW TO PERFORM SET-UP MENU ADJUSTMENTS (cont’d.) Items Contents WHITE BALANCE ADJUSTMENT BLUE DRIVE Adjusts the blue drive level. You can set (adjust) the white balance of the screen. … Decreases the blue drive level. This function (WHITE BALANCE) is set in the … Increases the blue drive level. screen. RED DRIVE Adjusts the red drive level. 1 While pressing the … Decreases the red drive level. SELECT button, press … Increases the red drive level. SELECT GREEN CUT OFF Sets th
ページ19に含まれる内容の要旨
SELECTING [ sub menu] IN PROCEDURE 4 RESETTING ALL MENU ITEMS TO You can also adjust items in procedure 5 with only the selected item displayed. Use this if the full menu screen THEIR FACTORY-SET (INITIAL) makes it difficult to observe the monitor image. VALUES 1Select the [ sub menu] item in procedure 4. 2Press the VOLUME/ You can reset all the items in the screen and screen to their factory-set (initial) values. ENTER button. The screen appears. This func
ページ20に含まれる内容の要旨
TROUBLESHOOTING Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance. Problems Points to be checked Measures (Remedy) Reference page No power supply Is the power plug loosened or Firmly insert the power plug. 5, 6 disconnected? No picture with Is the signal cable disconnected? Connect the signal cable firmly. 5, 6, 7 the power on I
