ページ1に含まれる内容の要旨
PD7130
PD7150
R
DLP Projector
User's Manual
www.PlanarHomeTheater.com
SOURCE
ENTER
MENU
ページ2に含まれる内容の要旨
Planar Systems, Inc. Corporate Headquarters 1195 NW Compton Drive Beaverton, OR 97006-1992 Planar Customer Support Telephone: US: 1-866-PLANAR1 (866) 752-6271 Outside US: (503) 748-5799 E-mail: PlanarSupport@planar.com Online Technical Library: http://www.planar.com/support Hours: M-F, 8am-8pm ET, 12pm-12am GMT
ページ3に含まれる内容の要旨
Preface Preface ENGLISH ABOUT THIS MANUAL This manual is designed for use with the PD7130/PD7150 DLP Front Projector. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. COPYRIGHT © Copyright 2006 This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any m
ページ4に含まれる内容の要旨
Notices WARNING! To meet FCC requirements, a shielded power cord is required in order to prevent interference. It is essential that only the supplied power cord is to be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not approved by the party responsible for compliance could void your authority to operate the equipment. WARNING! The projector cooling fan continues to run for approximately 90 seconds after the projec
ページ5に含まれる内容の要旨
Preface PRODUCT DISPOSAL This projector utilizes a tin-lead solder, UHP Lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. IMPORTANT RECYCLING INSTRUCTIONS Lamp(s) inside this product contain mercury. This product may contain other elec- Hg tronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Elec- tronic Ind
ページ6に含まれる内容の要旨
iv Preface
ページ7に含まれる内容の要旨
Contents Contents Preface ................................................................................... i Notices .................................................................................. ii Introduction Package Contents ................................................................. 2 Features ................................................................................ 2 Components .......................................................................... 3 Projector (
ページ8に含まれる内容の要旨
Factory Reset........................................................................... 31 Appendix Maintenance........................................................................ 34 About the Lamp ................................................................... 35 Caution Concerning the Lamp ................................................. 35 Replacing the Lamp................................................................. 35 Temperature LED (Temperature Overheat
ページ9に含まれる内容の要旨
Introduction Introduction 1
ページ10に含まれる内容の要旨
Package Contents Open the package and ensure that you have the following items: ON POWER OFF SOURCE 1 23 4 5 ENTER MENU EXIT USER MEMORY M1 M2 M3 ASPECT GAMMA OS AUTO BLANK LIGHT Remote control Two “AAA” size batteries Power cord (By country) User’s Guide CD RGB Component Cable (including this manual) Features • Newly developed LVDS (Low voltage differential signal) chip eliminates Color Breaking phe- TM nomena common with previous generation DLP projectors • Use of high-output lamp realizes b
ページ11に含まれる内容の要旨
Introduction Components Projector (Front and Top View) Lens shift dial Lens shift dial (Vertical) (Horizontal) POWER (ON/OFF) Press to turn the power on or off. LED Indicator (Green/Red) SOURCE Green: Standby Press to select the input SOURCE Red: Overheat source. ENTER Menu Navigation ENTER ( , , , ) Press to set selected items or Press to select menu items. adjustments in the menu. MENU MENU Press to view the OSD menu. Press again to hide the OSD menu. Intake vent Cooling fan 3 SOURCE E
ページ12に含まれる内容の要旨
Projector (Rear View) Source 5: Video/S-Video Source 3: DVI Terminal for connecting video Terminal for Digital equipment with an S-video or Video Interface. COMP1 COMP2 Composite Video terminal. VIDEO S-VIDEO PR/CR PB/CB Y PR/CR PB/CB Y RGB-HD DVI-D Y 12V Trigger Terminal for scr
ページ13に含まれる内容の要旨
Introduction Remote Control ON POWER OFF Power ON and Power OFF Source 2 Press to turn the power on and off. Press to select the Component 2 device. SOURCE 1 23 Source 3 Source 1 Press to select the DVI input. Press to select Component 1 device. 4 5 Source 4 Source 5 Press to select the PC device. Press to select Video/S-Video device. ENTER Menu Navigation ( , , , ) Press to set selected items or ENTER Press to display adjustment and setting adjustments in the menu. screens. MENU EXIT P
ページ14に含まれる内容の要旨
Using the Remote Control Note • The signal from the remote control can be reflected by the screen. When using the remote control: • Do not drop it, or expose it to moisture or high temperature. • The remote control may not function correctly under fluorescent lamps. Operate the projector away from fluorescent lamps. Inserting the Batteries The batteries (two “AAA”) are included in the package. Press down the tab on the cover 1 and slide the cover towards the direction of the arrow. Insert th
ページ15に含まれる内容の要旨
Connections and Setup Connections and Setup 7
ページ16に含まれる内容の要旨
Connecting the Projector to Other Devices Before Setting Up Notes • Before connecting, turn off both the projector and the devices to be connected. After making all connections, turn on the projector first and then the other devices. When connecting a computer, be sure that the computer is the last device turned on, after all connections are made. • Read the operation manuals of the devices to be connected before making connections. This projector can be connected to Video equipment: A VCR
ページ17に含まれる内容の要旨
PR/CR PR/CR PB/CB PB/CB 12V TRUGGER RGB-HD COMP2 COMP1 S-VIDEO VIDEO RS-232 Connections and Setup Connecting to Video Equipment Using a S-video or a Composite Video VCR or other video equipment Cable (VIDEO/S-VIDEO) Using a S-video or a composite video cable, a To S-video output terminal VCR, DVD Player or other video equipment To Video output terminal can be connected to the S-VIDEO or VIDEO terminals. Note • The S-VIDEO terminal uses a video signal system in which the picture is s
ページ18に含まれる内容の要旨
PR/CR PR/CR PR/CR PR/CR PB/CB PB/CB PB/CB PB/CB 12V TRUGG RGB-HD 12V TRUGGE RGB-HD DVI-D DVI-D AC110-240 AC110-240 COMP2 COMP1 COMP2 COMP1 S-VIDEO S-VIDEO RS-232 RS-232 Connecting to Component To analog component output terminal Video Equipment Using a Component Cable (Component 1 or 2) Use a component cable when connecting component video equipment such as DVD players and DTV* decoders to the Component 1 or 2 terminals. Component cable DVD player or *DTV is an umbrella term u
ページ19に含まれる内容の要旨
PR/CR PR/CR PB/CB PB/CB 12V TRUGG RGB-HD DVI-D AC110-240 COMP2 COMP1 S-VIDEO RS-232 Connections and Setup Connecting Using a DVI-D to Optional DVI-D to HDMI HDMI Cable accessory cable Use a DVI to HDMI cable when connecting HDMI video equipment such as DVD players To HDMI output terminal to the DVI terminal. Connect a DVI-D to HDMI cable to 1 the projector. • Secure the connectors by tightening the thumbscrews. Connect the above cable to the 2 video equipment. DVD player or DVI-D
ページ20に含まれる内容の要旨
PR PR/CR PB/CB PB/CB RGB-HD DVI-D AC110-240 COMP2 COMP1 Connecting the Projector to a Computer Connect the projector to the computer using an HD 15-pin VGA cable. Optional HD 15-pin accessory VGA cable • Secure the cable connectors by tightening the screws on both sides of the plug. Notebook Computer Notes HD 15-pin VGA cable (sold separately) • See page 39 “Computer Compatibility Chart” for a list of computer signals To VGA output terminal compatible with the projector. Using computer
