ページ1に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 1
User Manual (Part 2)
2.4 GHz Expansion
Handset E250
For use with AT&T models
E2555 • E2525 • E2600B
ページ2に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 2 You must charge See pages 2-3 batteries and register the STOP! for easy instructions handset before use For customer service or product Please also read information, visit our web site at Important Product Information www.telephones.att.com Enclosed in product package or call 1-800-222-3111 Table of contents Before you begin........................................1 Parts checklist.............................................1 Battery installation &
ページ3に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:02 PM Page 1 Before you begin This cordless telephone operates with If you move out of range during a the maximum power allowed by the phone conversation, you might hear Federal Communications Commission noise or interference. To improve (FCC). Even so, this handset and base reception, move closer to the base. can communicate over only a certain If you move out of range without distance — which can vary with the pressing OFF, your phone will be left locations o
ページ4に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 2 Battery installation & charging Install batteries as shown, then place the handset in the charger for at least 8 hours before use. You can keep batteries charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 6 hours. LOW BATTERY REDIAL MENU MEM Low battery indicator Return handset to charger to recharge when this symbol flashes. (Handset will beep when battery is low.) Press
ページ5に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 3 Registering the handset Enter base ID, then press OK Before using your new handset, you must register it with the base. During registration, you must enter the 15-digit ENTER BASE ID ID number of the telephone base. To find this number, go 123456789012345 to the base, press MENU, scroll down to select DISPLAY OK < BASE ID, then press OK. The handset provided with your telephone is automatically registered as Handset 1. Additional handsets will be a
ページ6に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 4 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap) 4
ページ7に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 5 Quick reference guide For complete instructions, please refer to the manual provided with your telephone. Softkeys Press a softkey to select a menu item displayed just above the key. Off/Clear During a call, press to hang up. Item 1 Item 2 Item 3 While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display. Phone/Flash Press to begin a call, then dial a number. Xfer/Intercom During a call, press to receiv
ページ8に含まれる内容の要旨
ATT-250CIB-d1.qxd 12/30/2003 2:03 PM Page 6 www.telephones.att.com Copyright © 2003 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corporation, licensed to Advanced American Telephones. Printed in China. Issue 1.1 AT&T 12/30/03.
ページ9に含まれる内容の要旨
ページ10に含まれる内容の要旨
