ページ9に含まれる内容の要旨
Getting started Charger installation Install the charger as shown below. Plug the power adapter into an electrical outlet not controlled by a wall switch. IMPORTANT INFORMATION 1. Use only the power adapter(s) supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 2. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are n
ページ10に含まれる内容の要旨
Getting started Battery installation and charging Install the battery as shown on page 7. Once you have installed the battery, the screen indicates the battery status (see table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 16 hours of continuous charging. See the table on page 29 for battery operating times. If the sc
ページ11に含まれる内容の要旨
Getting started Battery installation and charging Step 1 Step 2 Plug the battery Align the cover connector securely flat against into the socket inside the battery the handset battery compartment, compartment, matching then slide it the color-coded label. upwards until it Insert the supplied clicks into place. battery with the label THIS SIDE UP facing up as indicated. CHARGE light Step 3 Charge the handset by placing it face SET DATE forward in the telephone base or --/--/-- charger.
ページ12に含まれる内容の要旨
Adding the handset to your telephone base Adding and registering handsets Before using a new CL80100 handset, you must register it with the AT&T CL81100/CL81200/CL81300/CL82100/CL82200/CL82250/ CL82300/CL82350/CL82400/CL82500/CL82550/CL84100/ CL84200/CL84300 telephone system (purchased separately), the telephone system can accommodate up to 12 handsets. The handset with the CL81100/CL82100/CL84100 comes as HANDSET 1. You can register up to 11 additional handsets to the telephone base, and th
ページ13に含まれる内容の要旨
Adding the handset to your telephone base Adding and registering handsets The handset needs to register with the telephone base before use. You must register each handset separately. When first purchased, all expansion handsets show Out of range OR No pwr at base on the Out of range OR No pwr at base screen. The new handset should be charged without interruption for at least 30 minutes before registering to the telephone base. To register a handset to your telephone base 1. Make sure th
ページ14に含まれる内容の要旨
Adding the handset to your telephone base Deregistering a handset You can deregister handsets. You may need to deregister your handsets if: You have 12 registered handsets and need to replace a handset. -OR- You wish to change the designated handset number of your registered handsets. You must first deregister ALL the handsets, and then re-register each handset you wish to use, one at a time. Please read carefully through all the instructions on this page before beginning the deregistration
ページ1に含まれる内容の要旨
User’s manual
CL80100
DECT 6.0 expansion handset
for use with AT&T models
CL81100/CL81200/CL81300/
CL82100/CL82200/CL82250/
CL82300/CL82350/CL82400/
CL82500/CL82550/CL84100/
CL84200/CL84300
ページ2に含まれる内容の要旨
Congratulations on your purchase of this AT&T product. Before using this AT&T product, please read the Important safety information on pages 20-22 of this manual. For complete instructions, please refer to the manual provided with your CL81100/CL81200/CL81300/ CL82100/CL82200/CL82250/CL82300/CL82350/CL82400/ CL82500/CL82550/CL84100/CL84200/CL84300 telephone. You can also visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Model #: CL8010
ページ15に含まれる内容の要旨
Appendix Troubleshooting If you have difficulty with your phone, please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. The handset registration is unsuccessful. • Follow the handset registration instructions to re-register the handset (see Adding and Registering handsets on page 9). My telephone doesn’t work at all. • Make sure the power cord is securely plugged in. • Make sure you
ページ16に含まれる内容の要旨
Appendix Troubleshooting • If the previous suggestions do not work, disconnect the telephone base from the telephone jack and connect to a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your telephone service provider. • Your line cord might be malfunctioning. Try installing a new line cord. I cannot dial out. • First try all the suggestions above. • Make sure you have a dial tone before dialing. The cordless handset m
ページ17に含まれる内容の要旨
Appendix Troubleshooting Out of range OR No pwr at base appears on my cordless handset. • Ensure you plug the telephone base in properly and the power is on. • Place the cordless handset in the telephone base for one minute to allow the cordless handset and base to synchronize. • Move the cordless handset closer to the telephone base. You might have moved out of range. • Reset the telephone base. Unplug the electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute fo
ページ18に含まれる内容の要旨
Appendix Troubleshooting I get noise, static, or weak signals even when I’m near the telephone base. • If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter prevents noise and caller ID problems as a result of DSL interference. Please contact your DSL service provider for more information about DSL filters. • You may be able to improve the
ページ19に含まれる内容の要旨
Appendix Troubleshooting My cordless handset does not ring when I receive a call. • Make sure that the ringer is not off. Refer to Ringer volume in the user’s manual provided with your CL81100/CL81200/ CL81300/CL82100/CL82200/CL82300/CL82350/CL82400/ CL82500/CL84100/CL84200/CL84300 telephone. • Make sure you plug in the telephone line cord securely into the telephone base and the telephone jack. Make sure you plug in the power cord securely. • The cordless handset may be too far from the te
ページ20に含まれる内容の要旨
Appendix Troubleshooting My calls cut in and out while I’m using my cordless handset. • Other electronic products can cause interference with your cordless phone. Try installing your phone as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephones. • Do not install this phone near a microwave oven or on the same electrical outlet. You might experience decreased performance while the microwave oven is operating. • If you plug your phone
ページ3に含まれる内容の要旨
Parts checklist Your telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. User’s manual CL80100 DECT 6.0 expansion handset for use with AT&T models CL81100/CL81200/CL81300/ CL82100/CL82200/CL82250/ CL82300/CL82350/CL82400/ CL82500/CL82550/CL84100/ CL84200/CL84300 Charger for cordless handset with power adapter installed User's manual Cordless handset Battery Battery for compartment cordless handset cove
ページ4に含まれる内容の要旨
User’s manual CL80100 DECT 6.0 expansion handset for use with AT&T models CL81100/CL81200/CL81300/ CL82100/CL82200/CL82250/ CL82300/CL82350/CL82400/ CL82500/CL82550/CL84100/ CL84200/CL84300 Table of contents Getting started Quick reference guide - handset ......................................................................1 Installation ...................................................................................................................4 Charger installation .....................
ページ5に含まれる内容の要旨
Getting started Quick reference guide - handset CHARGE indicator On when the handset is charging in the telephone base or charger. qCID/-VOLUME Press qCID to show caller ID history. Press to scroll down while in menus. While entering names or numbers, press to move the cursor to the left. Press to decrease the listening volume when on a call. PHONE/FLASH Press to make or answer a call. During a call, press to answer an incoming call when you receive a call waiting alert. 1 While reviewing
ページ6に含まれる内容の要旨
Getting started Quick reference guide - handset MENU/SELECT Press to show the menu. While in the menu, press to select an item or save an entry or setting. pDIR/+VOLUME Press pDIR to show directory entries. Press to scroll up while in menus. While entering names or numbers, press to move the cursor to the right. Press to increase the listening volume when on a call. OFF/CLEAR OFF/CLEAR During a call, press to hang up. While in a menu, press to cancel an operation, back up to the previou
ページ7に含まれる内容の要旨
Getting started Quick reference guide - handset EQ During an outside call, intercom call, message or announcement playback, press to change the quality of the audio to best suit your hearing. Main menu Main menu Play messages The > symbol highlights Answering sys a menu item. Directory Call log >Play messages Answering sys Ringers Settings Website Using menus Menu Press MENU/SELECT to show the first menu item, Play messages. Press qCID or pDIR to scroll through menu items. Press MENU/SELEC
ページ8に含まれる内容の要旨
Getting started Installation You must install and See pages 6-7 charge the battery before STOP! for easy instructions. using the telephone. Your product may be shipped with a protective sticker covering the handset or telephone base display - remove it before use. For customer service or product information, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Avoid placing the telephone base too close to: • Communication devices such as:
