ページ1に含まれる内容の要旨
OPERATING RANGE
This cordless telephone operates within the maximum If you move out of range during a phone
power allowed by the Federal Communications Commission conversation, you might hear noise or interference. To
(FCC). Even so, this handset and base can communicate improve reception, move closer to the base.
over only a certain distance — which can vary with the
If you move out of range without pressing O, your
locations of the base and handset, the weather, and the
phone will be left “off
ページ2に含まれる内容の要旨
INSTALLATION Before You Install 1 Choose a location for the base near an electrical This phone requires a modular telephone jack and a outlet and a telephone jack. standard electrical outlet (110v AC) not controlled by a wall switch. 2 Install the handset battery. a) Remove b) Plug battery c) Place battery battery pack connector pack and wires compartment into handset. in compartment. cover by Use only AT&T pressing on battery 3301 the indentation (SKU# 91076). and sliding downward. d) Replace c
ページ3に含まれる内容の要旨
INSTALLATION Wall Installation 1 Connect the telephone line cord. 2 Connect the power cord. Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. Standard electrical outlet Mounting studs Modular telephone jack 3 Mount the base on the wall. Align holes on base with mounting studs on wall jack. Pull base down on mounting studs until it locks into place. 4 Follow Steps 3–5 in “Table/Desk Installation.” 2
ページ4に含まれる内容の要旨
INSTALLATION Belt Clip Installation Attach the belt clip to the cordless handset (optional). To attach To remove BATTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack This battery should remain charged up to six days with the 1 Remove the battery compartment cover on the ringer turned on and up to 12 days with the ringer off. A handset by pressing on the indentation and sliding the fully charged battery provides an average talk time of about cover downward. six hours. 2
ページ5に含まれる内容の要旨
TELEPHONE OPERATION Answer a Call Lift handset from base — OR — Headset Jack Press any key. You can use this telephone hands-free when you install a 2.5 mm headset, included or purchased separately. Plug the headset into the jack under the small rubber flap. Do not force the connection, but Make a Call make sure the plug fits securely. Press and wait for light to go on steadily. End a Call Place handset in base Flash/Call Waiting — OR — Access special telephone company Press O. subscriber se
ページ6に含まれる内容の要旨
TELEPHONE OPERATION Indicates handset is charging in base Page/Handset Locator Indicates handset Press once to page the is in use handset for up to one minute — OR — Press twice to cancel. 5
ページ7に含まれる内容の要旨
TELEPHONE MEMORY This cordless phone can store 10 telephone numbers, each up to 16 digits long. You can dial numbers stored in memory just by pressing P, M and a number button. Store Memory Numbers 1 Make sure the handset is off. 2 Press G. The phone light blinks. 3 Press the number button (0–9) Store a Pause where you want to store the in a Memory Number telephone number. Press to store a two-second pause 4 Dial the telephone in the dialing sequence. Each number (up to 16 digits) press adds a
ページ8に含まれる内容の要旨
IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the If you hear noise or interference when using the phone: suggestions below. For Customer Service, visit our website • Make sure the base antenna is fully upright. at www.telephones.att.com or call 1 800 222–3111. • You may be out of range. Move closer to the base. Please retain your receipt as your proof of purchase. • Press and release C to change to another of the 30 channels available. If noise is exceptionally loud, If
