ページ1に含まれる内容の要旨
Pacemark 4410
Setup Guide
59290803
ページ2に含まれる内容の要旨
Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by Oki Data.
ページ3に含まれる内容の要旨
Overview Conventions Used in this Setup Guide ................................................... 2 Safety ................................................................................................. 3 Introduction ...................................................................................... 5 Pacemark 4410 Features ......................................................................... 5 Select a Location ..........................................................................
ページ4に含まれる内容の要旨
Installation for Windows 2000 ............................................................. 36 Installation for Windows 95/98 ............................................................ 40 Installation for Windows NT 4.0 .......................................................... 43 Installation for Windows 3.1x .............................................................. 46 Front Panel Overview .................................................................... 49 Print Mode ................
ページ5に含まれる内容の要旨
Safety Your OKI printer has been carefully designed to give you years of safe, reliable performance. As with all electrical equipment, there are a few basic precautions you should take to avoid hurting yourself or damaging the printer: • Read the setup and operating instructions in this manual carefully. Be sure to save it for future reference. • Read and follow all warning and instruction labels on the printer itself. • Unplug the printer before you clean it. Use only a damp cloth; do not use l
ページ6に含まれる内容の要旨
• To avoid damaging the power cord, do not put anything on it or place it where it will be walked on. If the cord becomes damaged or frayed, replace it immediately. • If you’re using an extension cord or power strip with the printer, make sure that the total of the amperes required by all the equipment on the extension is less than the extension’s rating. Generally, the total ratings of all equipment plugged into any one power line should not exceed 15 amperes. Don’t exceed this unless you know
ページ7に含まれる内容の要旨
Introduction Pacemark 4410 Features • Reliable, heavy-duty - Reliability: 15,000 hours MTBF - Duty Cycle: 35,000 pages/month • Fast - 300 lines per minute - 1066 cps in High Speed Draft mode • Capable of handling 10-part carbonless forms up to 0.03 inch (0.79 mm) thick • Rugged, long-life printhead (400 million characters) • Wide, 136-column format • Network capable • Software selectable or auto-switched rear- and front-feed paper paths • Two user-settable menu configurations Pacemark 4410 Setu
ページ8に含まれる内容の要旨
Select a Location • Firm, level surface capable of supporting approximately 95 lbs. (43 kg) • Clearance to open cover • At least four inches (102 mm) additional clearance on both sides for adequate ventilation • Nearby power source • Room temperature: 41 to 95°F (5 to 35°C) • Relative humidity: 20 to 80% • Away from direct sunlight E-6 Pacemark 4410 Setup Guide
ページ9に含まれる内容の要旨
Unpacking Getting Started Caution! The Pacemark 4410 printer weighs approximately 95 lbs. (43 kg). Be very careful to take appropriate precautions when lifting it. We recommend that at least two people participate when lifting the printer. Check the contents: 1 2 3 4 5 1 Printer 2 Ribbon Cartridge 3 Paper Guide 4 Power Cord 5 Cable (only included with 4410s which have Print Server pre-installed) If anything is missing or damaged, contact your dealer immediately. The printer interface cable is no
ページ10に含まれる内容の要旨
Documentation Provided Setup Guide The document you’re holding. ™ OKIcare Brochure This brochure explains the Pacemark 4410 service enhancement programs available in the U.S. and Canada. On-line User’s Guide In addition to the printer drivers, the Pacemark 4410 CD contains ® ® • Adobe Acrobat Reader 3.0 software ® • User’s Guide Acrobat file: Recommended minimum requirements for viewing the on-line User’s Guide: desktop area = 800 x 600 pixels color palette = 256 colors. User’s Guide Contents: –
ページ11に含まれる内容の要旨
Installing the Printer Getting to Know the Pacemark 4410 Front View Tear Bar Cover Rear-Feed Access Cover Printhead Access Cover Control Panel On/Off Switch Front Access Door Tear Bar Cover Rear View Rear-Feed Access Cover Serial Port Back Port Access Access Door Cover Parallel Power Port Cord Port Network/Option Slot Pacemark 4410 Setup Guide E-9
ページ12に含まれる内容の要旨
Installation Remove the Shipping Restraints Save the shipping restraints and packing materials in case you ever need to ship the printer. 1. Remove the pieces of shipping tape, then peel the protective plastic film off the digital display. 2. Press on the area(s) marked “PUSH” and open the printhead access cover. 3. Remove the printhead shipping restraint and its retaining screw. Be sure to keep this restraint/screw: it is needed to lock the printhead in place should you ever need to move or sh
ページ13に含まれる内容の要旨
4. Remove the red rubber shipping restraints (1) at either end. 1 5. Open the tear bar cover, remove the shipping restraint and close the cover. Caution! Avoid the sharp, serrated tear bar. Pacemark 4410 Setup Guide E-11
ページ14に含まれる内容の要旨
Install the Ribbon Cartridge Prepare the Cartridge 1. Swing out the ribbon arms at either end of the cartridge until they snap into place. 2. Push in on the white plastic ribbon restraint (1) at the right end of the cartridge (this engages the ribbon take-up knob). 1 3. Pull out the red shipping restraint (1) and turn the blue knob (2) counterclockwise (in the direction of the molded arrows) to take up any excess slack in the ribbon. 2 1 E-12 Pacemark 4410 Setup Guide
ページ15に含まれる内容の要旨
Load the Cartridge 1. Move the printhead to the ribbon loading area (1). Caution! Make sure the printer is turned off before proceeding. 1 2. Install the ribbon cartridge in the printer: place the ribbon arms (1) over the metal tabs (2) at either end, then press down on the cartridge. 1 2 2 1 2 Pacemark 4410 Setup Guide E-13
ページ16に含まれる内容の要旨
3. Feed the ribbon behind the printhead (1), threading it around the black guides (2) on either side of the printhead. Be careful not to twist the ribbon: this can cause jams. 1 2 4. Turn the blue knob counter clockwise (in the direction of the molded-on arrows) to take up any slack in the ribbon. Caution! Do NOT turn the knob clockwise: this can cause the ribbon to jam. 5. Close the printhead access cover. E-14 Pacemark 4410 Setup Guide
ページ17に含まれる内容の要旨
Install the Paper Guide Hold the paper guide as shown and place it in the slots on the back of the printer. Pacemark 4410 Setup Guide E-15
ページ18に含まれる内容の要旨
Connect to the Computer/Network Connecting the Parallel Port The parallel port is a standard IEEE-1284-compatible, 36-pin port. It requires a shielded IEEE-1284-compatible, bi-directional cable no longer than 6 ft. (1.8 m). 1. Open the port access cover. 2. Plug the interface cable into the parallel port and secure it with the wire loops. 3. Close the port access cover, and attach the other end of the cable to the computer and secure it with the screws. Default settings for the parallel interfac
ページ19に含まれる内容の要旨
Connecting the Serial Port The serial port is a standard RS-232C, 25-pin port, with selectable baud rates of up to 38.4 Kbps. It requires a shielded RS-232C cable which is UL and CSA approved and no more than 50 feet (15 m) in length. 1. Open the port access cover and plug the interface cable into the serial port. 2. Secure the cable with the screws and close the port access cover. 3. Attach the other end of the cable to the computer and secure it with the screws. Default menu settings for the s
ページ20に含まれる内容の要旨
® Connecting the Ethernet Port (for Pacemark 4410 with Print Server Pre-Installed) The installed print server is EtherNet 10/100BaseT. The Ethernet port requires a cable with two twisted-wire pairs and an RJ45 plug for connection to the network. See the OkiLAN 6100e User’s Manual included with your printer for additional information. 1. Open the port access cover. 2. Plug one end of the short cable included with the printer into the network board and the other end of the cable into the parallel
