ページ1に含まれる内容の要旨
hi/lo
dup mon
channel/
volume
scan
Color profile: Disabled
Composite Default screen
UH041/
UH041P
Operating Guide
To bring outstanding wireless communication products
to people's lives throughout the world.
UH041 Manual.prn
UH041 Manual - UT01912AZ
Monday, October 13, 2003 6:52:17 PM
hi/lo
dup mon
channel/ volume
scan
ページ2に含まれる内容の要旨
Color profile: Disabled Composite Default screen CONTROL & INDICATORS INCLUDED IN YOUR PACKAGE: Please check which model you have - UH041 or UH041P. UH041 UH041P UH041 Radio UH041P Radio (2) Operating Guide Operating Guide Belt Clip Belt Clip (2) Charging Cradle with AC Adaptor NiMH Battery Pack (2) OPTIONAL ACCESSORIES Charging Cradle with AC RX TX Adaptor NiMH Battery Pack SCAN VOL VOX DUP VOX Earset HI hi/lo dup mon 13 15 14 channel/ volume scan RX TX 12 19 16 SCAN VOL
ページ3に含まれる内容の要旨
Color profile: Disabled Composite Default screen GETTING STARTED Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture. BATTERY INSTALLATION Your UH041/UHO41P radio uses 4 AAA ALKALINE or optional NiMH battery pack (UH041P includes NiMH battery pack) batteries for power. To avoid damage to the unit do not mix old and new batteries. To install the batteries: 1. Make sure your radio is off. 2. Remove the battery compartment door by pressing the ta
ページ4に含まれる内容の要旨
Color profile: Disabled Composite Default screen dup mon channel/ volume scan charge 1 charge 2 Power Point Place the UH041P into the charge cradle. The charge light will come on to indicate the unit is charging. Before operating the UH041P, charge the battery pack for 16 hours. Do not charge alkaline or non rechargeable batteries. BELT CLIP To attach the belt clip: Slide the belt clip until it snaps into place. Belt Clip Locker To remove the belt clip: To remove the belt clip. Press and hold b
ページ5に含まれる内容の要旨
Color profile: Disabled Composite Default screen OPERATION POWER ON/OFF Press and hold to turn the Radio on. A channel number will appear on the display. Press and hold to turn the Radio off. VOLUME Press volume or to increase or decrease the volume level. VOL 'VOL' icon appears on display while volume hi/lo is being adjusted. dup mon There are 8 Volume levels. Level 0 (No channel/ volume scan Audio) to Level 7 (Maximum Volume). ADJUSTING THE KEY BEEPS Your radio emits a beep each time one of t
ページ6に含まれる内容の要旨
Color profile: Disabled Composite Default screen SELECTING CHANNEL Press channel or to select the hi/lo dup mon desired channel. channel/ volume scan TO TRANSMIT AND RECEIVE The UH041/UHO41P uses the 40 UHF-CB Channels. For your reference a list of the available channels and corresponding frequencies is printed on page 10. 1. Before you transmit, listen for activity on the selected channel. TX 2. When the channel is clear, press PTT and hold the to transmit. hi/lo PTT 'TX' appears on the LCD. d
ページ7に含まれる内容の要旨
Color profile: Disabled Composite Default screen TRANSMIT Hi/Lo SELECT dup Press and hold for 2 seconds when the unit is in Transmit Lo and it will switch to Transmit Hi. 'HI' icon will appear on HI display. dup Press and hold for 2 seconds again to return to Transmit Lo setting. 'HI' icon will disappear from display. The RF transmit power of the UH041/UHO41P is selectable Transmit Power 0.3/1.0 W. AUTOMATIC SQUELCH FEATURE The UH041/UHO41P is equipped with an Automatic Squelch system whi
ページ8に含まれる内容の要旨
Color profile: Disabled Composite Default screen TO OPERATE IN DUPLEX MODE Duplex mode is only available from CH01 – CH08. Duplex mode is activated on a per channel basis and transmitting frequency on Duplex channels is CH31 – CH38. E.g., If the Repeater channel for your area is CH01, then while in Duplex mode the Transmit channel will become CH31 with the Receive channel being CH01. dup Press momentarily. The 'DUP' icon appears. dup Press again to deactivate the duplex operation. UH041/UHO41P
ページ9に含まれる内容の要旨
Color profile: Disabled Composite Default screen REPLY DELAY While scanning, the UH041/UHO41P stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 2 seconds for the return of the signal, otherwise, the radio resumes scanning. POWER SAVE Your UH041/UHO41P has a unique circuit designed to dramatically extend the life of the batteries. If there is no transmission nor an incoming call within 3 seconds, your Radio switches to the Power Save mo
ページ10に含まれる内容の要旨
Color profile: Disabled Composite Default screen VOX VOX is the automatic transmitting function by inputting voice PTT into the optional VOX headset mic without pressing the button. Press momentarily while in CTCSS mode to enter VOX sensitivity mode. The current selected VOX setting will flash on the CTCSS channel indicator display. Press Channel or to adjust the VOX sensitivity. 1 is the highest sensitivity and 4 is the lowest sensitivity. VOX can be turned off by selecting 'oF'. The'' VOX ico
ページ11に含まれる内容の要旨
Color profile: Disabled Composite Default screen UHF CHANNELS & FREQUENCIES Simplex Mode Duplex Mode Simplex Mode CH No. Transmit / Receive Transmit CH No. Transmit / Receive Frequency (MHz) Frequency (MHz) Frequency (MHz) 1 476.425 477.175 CH31 21 476.925 2 476.450 477.200 CH32 22 476.950 3 476.475 477.225 CH33 23 476.975 4 476.500 477.250 CH34 24 477.000 5 476.525 477.275 CH35 25 477.025 6 476.550 477.300 CH36 26 477.050 7 476.575 477.325 CH37 27 477.075 8 476.600 477.350 CH38 28 477.100 9 47
ページ12に含まれる内容の要旨
Color profile: Disabled Composite Default screen WARRANTY UNIDEN UH041/UH041P UHF CB RADIO Limited One Year Warranty Note: Please keep your sales docket as it provides evidence of warranty. Warrantor: Uniden Australia Pty Limited ACN 001 865 498Uniden New Zealand Limited Warranty only available in original country of purchase Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty, its UH041/UH041P UHF CB Transceiver Radio (hereinafter referred to as
