ページ1に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 1
INSTRUCTION MANUAL
CLT-2430
2.4-GHz
Digital Spread Spectrum
Cordless Telephone
with Call Manager Features
IMPORTANT
Charge the handset battery pack for a full 15 hours before using your
cordless handset for the first time.
www.sanyocanada.com
ページ2に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:36 PM Page 2 Introduction Congratulations on your purchase of the CLT-2430 cordless telephone. This phone is designed for reliability, long life, and outstanding performance utilizing the latest in 2.4-GHz Digital Spread Spectrum technology. Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. Features 2.4-GHz Digital Spread Spectrum Technology Dual Keypad Call Manager Features*: Caller ID, Caller ID on Call Waiting
ページ3に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 3 Controls and functions 1 2 5 3 6 14 7 15 8 16 9 17 10 11 18 4 19 12 13 20 1. Handset antenna 12. REDIAL/PAUSE key 2. Headset jack cover 13. Microphone 3. HandsFree speaker 14. CALL REVIEW/VOLUME (up) key 4. Battery compartment 15. INTERCOM/SELECT key 5. Earpiece speaker 16. CID/FLASH key 6. LCD display 17. Right cursor key ( ) 7. MEMORY key 18. SPEAKER key 8. TALK/END key 19. DELETE/SCAN key 9. CALL REVIEW/VOLUME (down) key 20. Handset charging contacts
ページ4に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 4 34 21 33 32 31 30 29 28 27 35 22 26 25 23 24 21. Handset retainer 22. Base charging contacts 23. INTERCOM/PAGE/FIND key 24. FLASH key 25. SPEAKER key 26. REDIAL/PAUSE key 27. MEMORY key 28. CALLERS indicator 29. CHARGE/IN USE indicator 30. INTERCOM indicator 31. SPEAKER indicator 32. VOICE MAIL indicator 33. Base antenna 36 37 38 39 34. Bottom bracket 36. Ringer Volume switch 35. VOLUME control 37. Pulse-Tone switch 38. DC power input 39. TEL LINE jack
ページ5に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 5 CONTENTS Getting Started Introduction/Features ..............................................inside front cover Controls and Functions............................................inside front cover Getting started Read this first..........................................................................................E2 Step 1: Checking the package contents.........................................E3 Basics Step 2: Setting up the base unit ................
ページ6に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 6 STARTED GETTING Read this first This cordless telephone must be set up before use. Follow these steps: Step 1 (page E3) Unpack and check the telephone and accessories. Step 2 (page E4 to E8) Choose the best location to set up the base unit. Base unit Step 3 (page E9 to E10) Insert the battery pack into the handset. You must charge the battery pack for a full 15 hours before using the phone. Handset About the digital security code This cordless telephon
ページ7に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 7 STARTED GETTING Checking the package contents Make sure you have received the following items in the package. • AC adaptor • Base unit • Handset (AD-350) • Bottom bracket • Rechargeable • Telephone line for desktop use battery pack cord (1) and wall-mounting (SANYO 3KR-600AAL) • This Owner's Manual • Belt clip E3
ページ8に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 8 STARTED GETTING Setting up the base unit Avoid places near electrical equipment such as refrigerators, computers, TVs, microwaves or fluorescent lamps. These may cause interference or reduce the operating range of the cordless telephone. Do the following steps: • Choose the best location • Connect the base unit • Choose the dialing mode Notes: • The location should be close to both a phone jack and a continuous power outlet which is not switchable. • B
ページ9に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 9 STARTED GETTING Desktop use Connect the base unit 1 If you want to install the base unit on the wall, see page E7. 2 To AC outlet To DC IN 9V AC adaptor (supplied) 3 To telephone outlet To TEL LINE Telephone line cord (supplied) Note: When connecting the power cord, make sure it does not create a trip or fire/electrical hazard. Avoid places where it could become chafed. 1 Snap the bottom bracket into the notches on the base. 2 Connect the AC adaptor t
ページ10に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 10 STARTED GETTING Notes: • Use only the supplied AD-350 AC adaptor. Do not use any other AC adaptor. • Connect the AC adaptor to a continuous power supply. • Place the base unit close to the AC outlet so that you can unplug the AC adaptor easily. • If your telephone outlet is not modular, contact your telephone company for assistance. Choose the dialing mode PULSE TONE Depending on your dialing system, set the PULSE-TONE switch as follows: If your dialin
ページ11に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 11 STARTED GETTING Mounting the base unit on a wall Standard wall plate mounting This phone can be mounted on any standard telephone wall plate. 1 Attach the bottom bracket to the base as 1 shown. Make sure all tabs snap into the notches on the base. 2 Plug the telephone line cord to the TEL LINE jack and the small plug of AC adaptor to the DC IN 9V jack. 3 Plug the telephone line cord into the telephone outlet. 4 Fit the AC adaptor cord into the mold
ページ12に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 12 STARTED GETTING 8 On the base unit, pull the handset retainer out Handset retainer of the slot. Rotate it clockwise 180 degrees. 9 Flip the retainer. Slide it back into the slot so that the lip of the retainer is up and the points down. The retainer holds the handset in place. Note: When the phone is mounted on the wall, the handset belt clip must be attached to hold the handset in the charging position. Do not place the handset with the display facing
ページ13に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:28 PM Page 13 STARTED GETTING Preparing the battery pack Charge the battery pack for a full 15 hours before you start using your phone. 1 Press on the battery cover and slide the cover down until it comes off. 2 Plug in the battery pack connector with the correct polarity (black and red wires), then insert the battery pack into the battery compartment. 3 Slide the battery cover on until it snaps into place. 4 Place the handset on the base. 5 Make sure that the CHARG
ページ14に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 14 STARTED GETTING Battery use time (per charge) With a fully charged battery: • Six hours continuous use. • Seven days when the handset is in the standby mode. When the battery charge level becomes low Low Battery When the voltage of the battery pack in the handset is very low and needs to be charged, the phone is programmed to stop functioning in order to save power. If the phone is not in use, Low Battery flashes and none of the keys will operat
ページ15に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 15 BASICS Making a call With the handset Dialing from standby mode 1 Enter the phone number. (Up to 32 digits.) Example: Enter 9057609944 9057609944 2 Press TALK/END. Talk flashes in the display. Talk 9057609944 The volume setting is displayed. For example, if the volume is set to high, the display shows: Talk 3 The number is dialed. The call time display Talk 0:00 appears about 5 seconds after line connection. 9057609944 4 To hang
ページ16に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 16 BASICS Dialing from talk mode 1 Press TALK/END or SPEAKER . Talk flashes on the display. Press TALK/END Press SPEAKER Talk Talk The volume setting is displayed. For example, if the volume is set to high, the display shows: Talk Talk The call-time display appears. 2 Dial the phone number. Example: Enter 9057609944 Talk 0:17 Talk 0:17 9057609944 9057609944 3 To hang up, press TALK/END or SPEAKER (or place the handset i
ページ17に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 17 BASICS With the base 1 Press SPEAKER on the base. The SPEAKER indicator lights. 2 Dial the number on the keypad. 3 When you finish the call, press SPEAKER on the base to hang up. E13
ページ18に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 18 BASICS Receiving a call With the handset 1 The phone rings. Incoming call appears. Incoming Call 2 Press TALK/END. Talk, the call time display and the volume setting appear. You can also press SPEAKER on the handset to answer the call. Talk 0:00 If you subscribe to Caller ID service, the display may show the caller’s name/number. (See page E30) 3 Talk with the caller. Talk 0:02 4 To hang up, press TALK/END. The call time disp
ページ19に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 19 BASICS With the base 1 The base rings. The CHARGE/IN USE indicator flashes. 2 Press SPEAKER. 3 When you finish the call, press SPEAKER to hang up. Call Waiting Note: You must subscribe to Call Waiting service to use this feature. When a call is received during a telephone call already in progress, you hear a beep. Press CID/FLASH to switch to the new call. If you also subscribe to Caller ID on Call Waiting (Visual Call Waiting), you will see the name
ページ20に含まれる内容の要旨
CLT2430 5th 8/9 8/10/00 4:29 PM Page 20 BASICS Lighted keypad The dialing keypad and the TALK/END key on the handset light up when you press any key on the keypad. The light turns off if no key is pressed for 5 seconds. Scanning Your phone automatically selects the clearest possible channel every time you receive or place a call. Should you wish to switch channels during a call, the handset provides a DELETE/SCAN button. Adjusting the ringer and speaker volume Ringer volume Ringer A High I
