ページ1に含まれる内容の要旨
$KI"$WVVQP"2JQPG
YKVJ"%CNNGT"+&
43-3901 OWNER’S MANUAL — Please read before using this equipment.
%106'065
Large Liquid Crystal Display – Displays three lines of
information, including the time, the number you dialed, and
FCC Statement .......................... 2
Caller ID information (see “Caller Id Operation” on Page 9).
Lightning ................................. 3
Preparation ................................. 3
Installing Batteries ................... 3
New Call Indicator
Selecting a Loca
ページ2に含まれる内容の要旨
(%%"56#6'/'06 "+/2146#06" # # This phone is Hearing Aid compatible. If an icon appears at the end of a paragraph, go to the box on that Your phone complies with Part 68 of FCC Rules. You must, page with the corresponding icon for pertinent information. upon request, provide the FCC registration number and the REN to your telephone company. Both numbers are on the — Warning — Important # Rý bottom of the phone. . . . . — Caution ± — Note You must not connect your phone to: • coin-operate
ページ3に含まれる内容の要旨
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase
ページ4に含まれる内容の要旨
plugged in to maintain the Caller ID and speed dialing memories. "9#40+0) " ý R R If you do not replace the batteries promptly, your Caller ID Dispose of old batteries promptly and telephone memory information may be lost. and properly. Do not burn or bury Rý them. 5'.'%6+0)"#".1%#6+10 Select a location for your telephone that is: • Near a telephone jack • Not in the way of normal activities in the area Your telephone connects directly to a modular telephone line jack. If your telephone wi
ページ5に含まれる内容の要旨
4. Plug the cord’s other end into the wall plate jack, then align the base’s keyhole slots with the wall plate studs and slide the phone downward to secure it. Keyhole Slots Wall Plate Studs Mounting Bracket To mount the phone directly on a wall, in addition to the preceding steps, you need two screws (not supplied) with heads that fit into the keyhole slot on the bottom of the base. 1. Drill two holes 83mm apart (vertically). Then thread a screw into each hole, letting the heads extend abo
ページ6に含まれる内容の要旨
4. Press UP or DOWN to select the first digit of the area code. Press DELETE to confirm the selection. The second U U U U flashes. 5. Repeat steps 1 through 4 to set the second and the third digit. Once you have confirmed the third digit of the area code, ;;;;D DD DJ;H J;H J;H J;HýJ?C ýJ?C ýJ?C ýJ?C;;;;ýýýý:7J; :7J; :7J; :7J; appears, and the hour digit flashes. 6. Press UP or DOWN to select the desired hour. FC FC FC FC appears for a PM hour. 7. Press DELETE to confirm. 8. Repeat steps 6
ページ7に含まれる内容の要旨
• If the dial tone continues, you have pulse service. Set TONE/PULSE to PULSE. 75+0)"610'"5'48+%'5 Some computer services, such as alternate long distance and bank-by-phone, require tone signals for communications. If you have pulse service, you can still use tone service. 1. Connect to the special service using pulse dialing. 2. When the special service answers, press to * temporarily switch to tone dialing. 3. When you complete the call and hang up the handset, the unit automatically re
ページ8に含まれる内容の要旨
75+0)"/76' To talk to someone on your end of the phone without the caller hearing your conversation, hold down MUTE. Release MUTE to resume your conversation. 75+0)"(.#5* FLASH performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting. For example, if you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press FLASH again to return to the first call.± ±"016'"±" 75+0)"4'&+#. Using Flash Pick up the
ページ9に含まれる内容の要旨
press an emergency memory icon (see the illustration on page 1). To store the number in a standard memory location, press a number key (0-9). %12;+0)"#"07/$'4"(41/"6*'"%#..'4" +&"+061"/'/14; 1. Lift the handset. 2. Press Up or DOWN until the desired number appears. 3. Press STORE twice. IJEH IJEH IJEH IJEH;;;; and C; C; C; C;C C C C appear on the display. 4. Press a memory location (0 to 9 on the keypad) to store the number in standard memory, or press any one of the three direct memory key
ページ10に含まれる内容の要旨
To review the records from newest to oldest, repeatedly press DOWN button. After you review all the records in memory, ;D ;D ;D ;D:ýE<ýB :ýE<ýB :ýE<ýB :ýE<ýB?IJ ?IJ ?IJ ?IJ appears. If an incorrect, invalid or incomplete Caller ID signal is received, the display shows BBBB????D D D D; ;; ;ý;HH ý;HH ý;HH ý;HHEH EH EH EH. If the name and number are not available due to the caller’s restriction, the display shows FH?L FH?L FH?L FH?L7J;ý97B 7J;ý97B 7J;ý97B 7J;ý97BBBBB. If the name and number are
ページ11に含まれる内容の要旨
2. Press CALL BACK again to confirm and dial the seven- digit number. Your telephone company may require a different format for making out-of area (toll) calls within your area code. When your telephone company requires you to dial more than a seven-digit number (same area code) to make toll calls within your area code, or an 11-digit number (different area code) use one of the 4 options below for Caller ID call back. Option 1 1 + Area Code + 7-digit number (11 digits) Option 2 1+7-digit n
ページ12に含まれる内容の要旨
To delete all of the call records at once, at the normal Limited One-Year Warranty display, hold down DELETE for about three seconds. ;H7I;ý ;H7I;ý ;H7I;ý ;H7I;ý This product is warranted by RadioShack against 7B 7B 7B 7BBý9 Bý9 Bý9 Bý97 77 7BBBBBBBBI II I appears. manufacturing defects in material and workman- ship under normal use for one (1) year from the date of purchase from RadioShack company- Press DELETE. The system deletes all call records. DE DEýý997BBI 7BBI DE DEýý997BBI 7BBI owned
