ページ1に含まれる内容の要旨
Oricom eco50 Series
DECT Digital Cordless Phone
USER GUIDE
Keep this user guide for future reference.
ページ2に含まれる内容の要旨
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 GETTING STARTED 2 BASIC Op ERATION 6 CALLER ID Op ERATION 9 LNR Fu NCTION (LAST Nu MBER REDIAL) 11 p h ONEBOOk 12 CORDLESS hANDSET Op ERATION 13 App ENDIx 16 Cu STOMER Supp ORT 21
ページ3に含まれる内容の要旨
WARNINGS AND SAFETY INFORMATION 1 recommended that you position the base unit at least IMPORTANT one metre from such appliances. • Avoid exposure of this telephone to moisture or liquid. • This telephone complies with applicable safety requirements for exposure to radio waves (EMR). • To prevent electric shock, do not open the handset or The mean power of this telephone does not exceed base cabinet. 20mW limit at which point testing is required. • Avoid metallic contact (e.g. metal clips,
ページ4に含まれる内容の要旨
2 GETTING STARTED Installation and Charger WARNING 1. Connect the mains adaptor (supplied) DO NOT USE STANDARD/ALKALINE BATTERIES IN ! THIS PRODUCT, AS THERE IS A RISK OF EXPLOSION to the socket on the back of the base AND/OR INJURY. USE ONLY NI-MH RECHARGEABLE unit and to the wall mains supply. BATTERIES AS SPECIFIED IN THIS USER GUIDE. 2. Connect the telephone cord to the CONTACT ORICOM FOR REPLACEMENT BATTERIES. phone socket on the back of the base RISK OF EXPLOSION IF BATTERY IS REPLA
ページ5に含まれる内容の要旨
GETTING STARTED 3 Pack contents Purchasing additional handsets Depending on the model you have purchased this pack You may expand your eco50 by adding more handsets should contain the following items: (eco5050WH). These can be purchased separately from the retailer where you purchased the product, or directly If any of these are missing, please contact Oricom directly. from Oricom (Australia). The eco50 can accommodate a total of 5 cordless handsets. eco50-1 eco50-2 Base units 1 1 Important:
ページ6に含まれる内容の要旨
GETTING STARTED Your cordless handset 1 Talk 2 Left / Recall / Dial mode 3 Handsfree 4 Phonebook 5 Right / CID (Caller ID) 1 6 Intercom 2 5 7 Delete / Mute 3 6 4 7 8 Numeric keys / Ringer Off (On) 9 * 8 10 Ringer Melody / Ringer Volume / Receiver Volume 11 # / Keypad lock 11 9 12 LNR (Last Number Redial) / Pause /Long (Short) 10 12 flash
ページ7に含まれる内容の要旨
GETTING STARTED Understanding the cordless handset display Left Arrow / Phonebook records are being reviewed Battery level (3 bars fully charged) Ringer is turned off Speakerphone on Keypad lock Connected to telephone line Flashes when there is an incoming call X appears: microphone muted Caller display Antenna in range / out of range Intercom call to another handset Right Arrow / Message waiting
ページ8に含まれる内容の要旨
6 BASIC Op ERATION During standby Answering an incoming call When there is an incoming call, the phone rings and flashes Note: on the display. If a CID record is received, flashes and the If the power is not connected to the base unit. caller information is displayed. The cordless handset CANNOT operate. 1. Press [ ] key to answer the call. 2. Press [ ] key again to end the call. Cordless handset's LCD display Making an external call HANDSET 1 : Handset number : Current battery leve
ページ9に含まれる内容の要旨
BASIC Op ERATION Mute feature Checking the signal strength Place a call on hold so that the caller will NOT be able to The signal icon displays the link status between your hear you but you can still hear the caller. handset and the base unit. A steady icon means your handset and the base unit are linked. A flashing icon During talking mode, means your handset and the base unit are not linked. 1. Press [ ] key on the handset to mute the call, is If you move too far away from the base un
ページ10に含まれる内容の要旨
BASIC Op ERATION Recall selection Handsfree mode You can use the Recall button on your telephone when using During talking or standby mode, your network operator's services such as call waiting etc. 1. Press [ ] key to switch to speakerphone mode. A subscription may apply for these services. Contact your 2. Press [ ] key again to cancel this feature. network operator for more information. If this is not working correctly, change the setting using the instruction below: Volume adjustment S
ページ11に含まれる内容の要旨
CALLER ID Op ERATION 9 If you subscribe to your telephone operators service 1. Press [ R/ ] key. You will hear a dial tone. (charges may apply), numbers of the incoming calls will be 2. Press [ 2 ] to put the current call on hold and talk with displayed on the screen and stored in the call log (please the second caller. consult your telephone service provider for details). 3. Repeat steps 1-2 to swap between the two callers. The eco50 series can store the last 20 calls including: the recor
ページ12に含まれる内容の要旨
10 CALLER ID Op ERATION Store a CID number Delete CID record(s) You can save a CID record into the Phonebook/Direct While you are viewing the CID record that you wish to memory provided that it contains a valid phone number and delete, the Phonebook/Direct memory is not full. Press and hold [ ] key for about 3 seconds. While you are viewing the CID record that you wish to save, Note: 1. Press and hold [ ] key for about 2 seconds. The If there are no more CID records, a message “NO” is fol
ページ13に含まれる内容の要旨
LNR Fu NCTION (LAST Nu MBER REDIAL) 11 2. The space after the last digit of the Redial number will Redial the last number blink, and you can press numeric keys to edit the Redial number. Then press [ ] key to confirm. Your cordless handset stores the last 3 external numbers dialled, up to 24 digits per number. If the number exceeds 3. Press the numeric keys to edit the memory location 24 digits, the last 24 digits will be stored to memory. (0-9) where you want to store the number. If you
ページ14に含まれる内容の要旨
12 p h ONEBOOk Add new records Review / Edit / Dial stored Phonebook records You can store up to 10 phonebook records in each handset. Each record can contain up to 24 digits per number. During standby mode, During standby mode, 1. Press [ ] key. The following will appear on the display. 1. Press and hold [ ] key until the icon appears on the display. 2. Press the numeric keys to enter the telephone number. If you made a mistake, press [ ] key to edit it. Press and hold [ ] key to dele
ページ15に含まれる内容の要旨
CORDLESS hANDSET Op ERATION 13 1. Press and hold [ ] key. Voicemail indication – network service 2. Press [ R/ ] or [ \ ] key to select the melody option (1 to 9 for adjustment). Note: 3. Press [ ] key to confirm. Volcemail Indication Service. Requires subscription with Handset ringer volume your netwok service provider. During standby mode, Voicemail indication is a visual voicemail alert. On this 1. Press [ ] key. Display shows the current volume level. phone, you will see an envelope
ページ16に含まれる内容の要旨
1 CORDLESS hANDSET Op ERATION 2. Key the handset number (1, 2, 3, or 4) you wish to Multi-handset Operation transfer. Your eco50 series phone can have up to 5 handsets 3. Press [ ] key to exit Intercom mode and return to registered to the base unit. Each handset has its own number standby mode. HS-1, HS-2, HS-3, HS-4 and HS-5, shown on the left-hand side of the display. With 2 or more handsets you can: Conference calls This function allows 3 parties (yourself + external call + • Make in
ページ17に含まれる内容の要旨
CORDLESS hANDSET Op ERATION 1 3. Enter the base pin code (0000). If the pin is wrong, the Note: handset will restart searching for the base. When the keypad is locked, [ ] key and [ INT ] key can 4. When the handset is registered, it will show “HS” be used to answer an external or intercom call. followed by the handset number. Note: Registration If the base is full and cannot add any more handsets, you will hear a tone. See the next section to remove a handset. Register new handsets on the
ページ18に含まれる内容の要旨
16 App ENDIx Troubleshooting Problem Possible cause(s) Solution(s) No dial tone on the 1. The base unit is not proper ly connected. 1. Chec k CONNECTION to power and telephone line. cordless handset. 2. T oo far from the base unit. 2. Mo ve handset CLOSER to base unit. 3. Batter y charge is low. 3. CHARGE batter y. 4. Incorrect batter y polarity. 4. RE-INSER T batteries and check + and . 5. Re-register handset. 5. Handset not registered. Antenna symbol is 1. The handset is not registered. If
ページ19に含まれる内容の要旨
App ENDIx 1 Problem Possible cause(s) Solution(s) No symbol on the 1. Battery is empty. 1. CHARGE batter y. display. 2. The product is not proper ly connected. 2. Mak e sure your product is properly PLUGGED-IN. Bad audio quality 1. I nterference from nearby electrical appliance. 1. Try a different connection point, one that is away from (crackles,echo, etc.). other electrical appliances. 2. Base unit is installed in a room with thic k walls. 2. Install the base unit in a DIFFERENT room OR u
ページ20に含まれる内容の要旨
1 App ENDIx Problem Possible cause(s) Solution(s) Cannot make/answer a 2nd call service can be activated. Check with your service provider. Check the recall 2nd call selection is correct. Note: If none of the above solutions help, reset your phone by disconnecting the mains power from the base and removing batteries from handset/s. Reconnect after 15 minutes. Alternatively please contact Customer Service on 1300 889 785.
