ページ1に含まれる内容の要旨
®
term
D Analog Cordless
User’s Guide
ページ2に含まれる内容の要旨
Controls and Functions 1 memory – Enters or recalls numbers in mem- ory. 2 talk – Answers or places calls. 3 tone – Switches to tone dialing in pulse dial mode. 4 redial – Redials the last number. 5 pause – Adds a timed pause in a memory dialing sequence. 6 talk/battery low – An LED that indicates when the phone is in use or the battery is low. 7 mute – Turns off the handset microphone while you are using the telephone. 8 flash – Accesses call waiting (if available), transfer and confe
ページ3に含まれる内容の要旨
Connecting the Base Unit 1. Connect the telephone line cord to the “TEL LINE” jack on the base unit and to a telephone outlet. 2. Connect the AC adapter to the DC IN 9V jack and to a standard 120 V AC wall outlet. 3. Set the base unit on a desk or tabletop and place the handset on the base unit. 4. Raise the antenna to a vertical position. Before plugging the telephone line into your new telephone, the rechargeable nickel-cadmium battery pack must be fully charged. Charge the battery fo
ページ4に含まれる内容の要旨
Receiver, Ringer Tone and Volume Control The telephone has two ringer tones and each tone has two volume levels. While the telephone is idle, continue to press volume until you hear the ringer tone and volume level you want. The telephone has four receiver volume levels: Low, Medium, High, Maximum. While on a call, continue to press volume until you hear the volume level you want. (When you hang up, the telephone retains the last volume setting selected.) Muting the Handset The handset micro
ページ5に含まれる内容の要旨
Storing Mixed Tone/Pulse Numbers If the telephone is set up for pulse dialing, mixed mode numbers can be stored to easily access long distance services. 1. Remove the handset from the base unit. 2. Press memory. (The talk/battery low LED flashes and a beep is heard.) 3. Enter the number(s) to be dialed in pulse mode. 4. Press tone on the handset to enter a pause. (This also counts as one digit.) 5. Enter the number(s) to be dialed in tone mode. 6. Press memory and enter the memory location (0
ページ6に含まれる内容の要旨
Replacing a Stored Number When you enter the memory location number, any number previously stored for the memory location is replaced. Erasing a Stored Number 1. Remove the handset from the base unit. 2. Press memory twice. 3. Enter the memory location number (0~9) you want to erase. (You will hear a long beep confirming the number has been erased.) Selecting a Different Channel You can manually change the telephone channel for clearer operation. There are 30 factory-set channels from which
ページ7に含まれる内容の要旨
Headset Installation Your telephone may be used with an optional headset. To use this feature, simply plug the headset into the headset jack on the handset. Your telephone is ready for handsfree conversation. Setting the Dial Mode Switch Place the switch in the “Tone” position for tone dialing, or the “Pulse” position for pulse dialing. The ability to pulse dial is dependent upon the telephone system and/or the outside lines to which term the D Analog Cordless is connected. Charging the Ba
ページ8に含まれる内容の要旨
Beltclip Installation 1. Insert the beltclip into the holes on each side of the handset. 2. Press down firmly until it clicks into the holes. If you have wall mounted the base, you cannot place the handset with the keypad facing inside. Pull both sides of the beltclip out of the holes to remove. term D Analog Cordless is hearing aid compatible. 7
ページ9に含まれる内容の要旨
Optional Available Parts Part Description Stock Number Headset with Foam Covered Ear and Microphone 730616 Replacement AC Adapter for Base Unit 760625 Replacement String-Type Beltclip 730624 Replacement Wall Mount Unit 730623 8
ページ10に含まれる内容の要旨
© 2001 NEC America, Inc. Document Revision 1 The material contained herein is subject to change without prior notice at the sole discretion of NEC America, For more information contact: Inc. NEC America, Inc. 6555 N State Highway 161 term® Irving, TX 75039-2402 D is a registered trademark of NEC Corporation. AutoTalk, AutoStandby, Random Code, UltraClear Plus, www.cng.nec.com and AutoSecure are trademarks of Uniden America Corporation. 750229-0
