ページ1に含まれる内容の要旨
ACD
SUPERVISOR / SENIOR SUPERVISOR
User Guide for the Superset™ 4150 Telephone
ページ2に含まれる内容の要旨
DUE TO THE DYNAMIC NATURE OF THE PRODUCT DESIGN, THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. MITEL CORPORATION, ITS AFFILIATES, AND/OR ITS SUBSIDIARIES ASSUME NO RESPONSIBILITY FOR ERRORS AND OMISSIONS CONTAINED IN THIS INFORMATION.
Copyright 2004, MITEL Corporation. All rights reserved.
ページ3に含まれる内容の要旨
Contents GETTING STARTED Introduction..........................................................................................5 Using a Headset ..................................................................................6 Logging In / Out ...................................................................................9 QUEUE STATUS Queue Status at a Glance..................................................................13 Displaying a Group’s Queue Status .............................
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
GETTING STARTED
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
Introduction This guide provides instructions for using ACD supervisor and senior supervisor features on SUPERSET 4150 telephones. Refer to your SUPERSET 4150 User Guide for a description of your telephone, and non-ACD features. Some of the personal keys on your telephone are programmed as QUEUE STATUS keys or AGENT STATUS keys, and one may be programmed as a SHIFT key. You use these keys to monitor the status of agents and agent groups. Supervisor or senior supervisor? Supervisors monitor agent
ページ8に含まれる内容の要旨
Using a Headset Note: Your system administrator may have enabled full-time headset operation on your telephone. Telephones with full-time headset operation enabled must be operated only with headsets. A headset can be used either in regular answer mode or with the Auto Answer feature programmed. Most headsets are installed using the same jack that the handset plugs into. MITEL’s Headset with Feature Control Switch plugs into the dedicated headset jack (the jack nearest the front of the telephone
ページ9に含まれる内容の要旨
To Install a Headset with Feature Control Switch IMPORTANT NOTE: MITEL’s Headset with Feature Control Switch must be installed in the dedicated headset jack (the jack nearest the front of the telephone). Installation will disable your handset microphone. Disconnecting the headset at the jack or at the quick-disconnect plug restores handset operation. To install the headset for your use, perform the following tasks: 1. When the telephone is not in use, lift the handset from the cradle and carefu
ページ10に含まれる内容の要旨
Handling Calls with a Headset (no Feature Control Switch): To answer a call (when Auto Answer is disabled): • Press the flashing Line Select key. To hang up: • Press the Hang-Up softkey. Handling Calls with a Headset with Feature Control Switch: To answer a call (when Auto Answer is disabled): • Quickly press and release the Control Switch. To mute the headset microphone (Headset with Feature Control Switch only): • Press and hold the Control Switch. To hang up: • Quickly press and release the C
ページ11に含まれる内容の要旨
Logging In / Out Your system administrator should have assigned you an identification number. Your identification number allows you to access the ACD system. Check with your system administrator if you don’t have an identification number. Note that you can’t program your telephone’s personal keys while you’re logged in. To log in: 1. Enter the Login/Logout access code. 2. Enter your identification number. If you’ve logged in successfully, you hear dial tone and ACD LOGIN appears in your telephon
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
QUEUE STATUS
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
Queue Status at a Glance The indicator beside a QUEUE STATUS key shows the current status of the call waiting queue for the associated agent group. Refer to Table 5 in the Reports and Indicators section for information on how to interpret the queue status indicator flash rates. Displaying a Group’s Queue Status A QUEUE STATUS key allows you to display an agent group’s queue status. 1. Press a QUEUE STATUS key. The following information is displayed: a) the agent group number and NAME b) the NUMB
ページ16に含まれる内容の要旨
Displaying Reports You can display queue status reports for your agent group. Refer to Table 3 in the Reports and Indicators section for a list of the available queue status reports. If you’re responsible for more than one agent group, you can also access agent status reports using the Agent softkey. Refer to Table 4 in the Reports and Indicators section for a list of the available agent status reports. To display queue status reports: 1. Press a QUEUE STATUS key. 2. Press a key on the dial pad.
ページ17に含まれる内容の要旨
Scrolling Through Reports You can also scroll through queue status reports and agent status reports. To scroll through group status reports: 1. Press a QUEUE STATUS key. The number and name of the group associated with the report data appears in the top line of the display. 2. Press a key on the dial pad. The report associated with that key is displayed. 3. Press the Next Report or Previous Report softkey to scroll through the queue status reports. To scroll through agent status reports: 1. Pres
ページ18に含まれる内容の要旨
About the SHIFT Key If you’re responsible for more agent groups than there are QUEUE STATUS keys on your telephone, you must use the SHIFT key to access the other agent groups. The SHIFT key allows you to access more than one agent group from a single QUEUE STATUS key. The status indicator beside the SHIFT key turns on when the shift function is activated. An example: If you’re supervising nine agent groups, but only have four QUEUE STATUS keys programmed on your telephone, you can press the SHI
ページ19に含まれる内容の要旨
Table 1 further illustrates this example: Table 1: SHIFT Key Operation for Queue Status Key Number With No Shift After 1st Shift After 2nd Shift After 3rd Shift 1 Agent Group 1 Agent Group 5 Agent Group 9 Agent Group 1 2 Agent Group 2 Agent Group 6 none Agent Group 2 3 Agent Group 3 Agent Group 7 none Agent Group 3 4 Agent Group 4 Agent Group 8 none Agent Group 4 Need a reminder? If you forget how many times you have pressed the SHIFT key: 1. Press SUPERKEY. 2. Press SHIFT. The shift count ap
ページ20に含まれる内容の要旨
